一种减少失速保护虚警率的混合滤波方法

针对飞机失速保护设计过程中易出现虚警的情况,提出一种基于FIR和传统滤波器相结合的混合滤波方法。结合飞机本体的运动特征,对参与失速保护逻辑运算的两个重要参数,即侧向加速度和迎角信号进行频率分析,基于信号的特征设计混合滤波器,然后采用Simulink滤波工具箱设计滤波器对信号进行滤波处理。仿真结果表明该方法能够减少虚警率的发生,特别是大背景噪声下的虚警率能够得到较好抑制,验证了滤波器设计正确性,从而提高失速保护功能对适航条款符合性。该滤波器设计方法,不但可以有效解决本文提到的问题,对于其他涉及信号处理的系统设计同样具有借鉴意义。     

Numerical analysis and optimization of boundary layer suction on airfoils

Numerical approach of hybrid laminar flow control(HLFC) is investigated for the suction hole with a width between 0.5 mm and 7 mm. The accuracy of Menter and Langtry’s transition model applied for simulating the flow with boundary layer suction is validated. The experiment data are compared with the computational results. The solutions show that this transition model can predict the transition position with suction control accurately. A well designed laminar airfoil is selected in the present research. For suction control with a single hole, the physical mechanism of suction control, including the impact of suction coefficient and the width and position of the suction hole on control results, is analyzed. The single hole simulation results indicate that it is favorable for transition delay and drag reduction to increase the suction coefficient and set the hole position closer to the trailing edge properly. The modified radial basis function(RBF) neural network and the modified differential evolution algorithm are used to optimize the design for suction control with three holes. The design variables are suction coefficient, hole width, hole position and hole spacing. The optimization target is to obtain the minimum drag coefficient. After optimization,the transition delay can be up to 17% and the aerodynamic drag coefficient can decrease by 12.1%.     

Specific grinding energy and surface roughness of nanoparticle jet minimum quantity lubrication in grinding

Nanoparticles with the anti-wear and friction reducing features were applied as cooling lubricant in the grinding fluid. Dry grinding, flood grinding, minimal quantity of lubrication（MQL）, and nanoparticle jet MQL were used in the grinding experiments. The specific grinding energy of dry grinding, flood grinding and MQL were 84, 29.8, 45.5 J/mm³, respectively. The specific grinding energy significantly decreased to 32.7 J/mm³ in nanoparticle MQL. Compared with dry grinding, the surface roughness values of flood grinding, MQL, and nanoparticle jet MQL were significantly reduced with the surface topography profile values reduced by 11%, 2.5%, and 10%,respectively, and the ten point height of microcosmic unflatness values reduced by 1.5%, 0.5%,and 1.3%, respectively. These results verified the satisfactory lubrication effects of nanoparticle MQL. MoS₂, carbon nanotube（CNT）, and ZrO₂ nanoparticles were also added in the grinding fluid of nanoparticle jet MQL to analyze their grinding surface lubrication effects. The specific grinding energy of MoS₂ nanoparticle was only 32.7 J/mm³, which was 8.22% and 10.39% lower than those of the other two nanoparticles. Moreover, the surface roughness of workpiece was also smaller with MoS₂ nanoparticle, which indicated its remarkable lubrication effects. Furthermore,the role of MoS₂ particles in the grinding surface lubrication at different nanoparticle volume concentrations was analyzed. MoS₂ volume concentrations of 1%, 2%, and 3% were used.Experimental results revealed that the specific grinding energy and the workpiece surface roughness initially increased and then decreased as MoS₂ nanoparticle volume concentration increased.Satisfactory grinding surface lubrication effects were obtained with 2% MoS₂ nanoparticle volume concentration.     

FGH96/GH4169高温合金惯性摩擦焊微观组织及演变过程

对FGH96/GH4169异质高温合金惯性摩擦焊接头组织形貌及演变过程进行分析,测量了焊接过程的界面温度。结果表明,惯性摩擦焊近界面处最高温度超过1100℃,达到母材强化相固溶温度区间。摩擦初期GH4169侧率先产生磨损颗粒;摩擦过渡期磨损颗粒被细化,摩擦界面形成高温粘塑性金属,在顶锻压力作用下开始形成飞边,夹杂物随之被挤出;准平衡摩擦阶段界面处高温粘塑性金属被持续挤出,飞边增大。焊后于焊接界面处形成等轴细晶区,细晶区与母材间为热力影响区,产生明显的变形,形貌为拉长晶粒。     

采用排间界面静压约束伴随方法的多级压气机叶片优化

为解决伴随优化应用在多级压气机中出现的优化工况点漂移问题,在前期薄层N-S方程伴随方法基础上,对目标函数——出口熵增不仅施以质量流量、总压比约束,还添加排间界面静压展向分布作为新的约束条件.以某5级压气机为对象,对其中第1级转、静叶分别在首1.5级和全5级压气机环境下进行了优化.结果表明,施加排间界面静压展向分布约束能够显著解决优化工作点漂移问题,优化后5级压气机的效率提高0.4个百分点.      

基于概率统计的DS/FH系统干扰检测算法

基于时频分布的干扰检测算法是DS/FH（Direct Sequence/Frequency Hopping,直接序列扩频/跳频扩频）系统干扰检测的传统手段,针对其运算量大、实时性差,以及无法检测某些特殊干扰信号等问题,提出一种基于概率统计的干扰检测算法.通过统计DS/FH系统频谱图中各频率的幅值出现位置,以DS/FH信号与干扰信号频谱分布规律的差别为判决依据,完成DS/FH系统中干扰信号的检测.分析和仿真结果表明：该检测算法能够有效识别DS/FH系统中的典型干扰信号,与传统基于时频分布的检测算法相比,能够实现某些特殊干扰信号的有效检测;同时,由于该算法不需要进行复杂的时频联合分析,其运算复杂度大大降低,能够实现DS/FH系统干扰信号的快速检测.     

无线电高度表信号模拟器射频信号延时/衰减模块设计

无线电高度表程控信号模拟器是无线电高度表自动测试系统（ATE,ATS）的重要组成部分,而射频信号延时/衰减模块则是无线电高度表程控信号模拟器3个功能模块组件中的核心模块。研制了一种采用声表面波（SAW）延迟线作为射频信号延时器件、射频衰减器作为射频信号功率衰减器件,通过程控射频开关控制不同声表面波延迟线的切换,包含射频信号变频、放大等结构电路的无线电高度表信号模拟器射频信号延时/衰减模块。经无线电高度表自动测试系统的实际工程应用表明,该无线电高度表射频信号延时/衰减模块对C波段（4.2～4.4 GHz）射频调制信号的延时精度高、衰减范围大,体小、质轻,适合置于无线电高度表测试适配器内部使用,具有较高的工程应用价值。     

基于EFFD方法的自然层流短舱优化设计

采用extended free-form deformation(EFFD)方法研究了自然层流(natural laminar flow,NLF)短舱的气动外形优化设计方法.使用基于Bernstein基函数的EFFD方法完成了NLF短舱剖面的参数化,利用基于k-εSST(shear stress transport)两方程湍流模型的γ-θ转捩模型进行自然转捩预测,结合EFFD、一种混合动网格方法、Kriging代理模型和改进的粒子群算法(particle swarm optimization,PSO)建立了针对NLF短舱气动外形的优化设计框架.采用该框架分别对通气NLF短舱和带动力NLF短舱进行优化设计.单独通气NLF短舱优化结果的外表面实现48%的层流,阻力系数比初始通气NLF短舱减小了0.0003.带动力NLF短舱的优化结果外表面保持了41%的层流.这些结果表明采用相关技术建立的优化设计框架在NLF短舱设计中具有一定应用价值.     

温度条件对碳纤维上浆剂与双马树脂反应及其复合材料界面粘结的影响

为了研究工艺温度对复合材料界面的调控作用,设计采用三阶段固化工艺(即扩散、固化和后固化),考察了不同温度制度下3种碳纤维/双马树脂(BMI)复合材料界面粘结性能的变化规律。采用原子力显微镜(AFM)和傅里叶变换红外光谱(FTIR)深入分析了上浆剂对纤维表面粗糙度和化学特性的影响,研究了上浆剂的反应活性及其与双马树脂的反应性,采用微珠脱粘方法测试了碳纤维/树脂的界面剪切强度(IFSSs)。结果表明,200℃处理2h后3种碳纤维上浆剂均发生部分反应,并且170℃,2h后上浆剂均与双马树脂发生化学反应。对比不同温度条件可以发现后固化阶段对碳纤维/双马体系的界面剪切强度影响显著,未经后固化的复合材料界面性能最低;110℃和140℃恒温扩散阶段对碳纤维/双马体系的界面剪切强度的影响不明显。同种温度条件下,CF1和CF3上浆剂与双马树脂的反应程度高于CF2,相应的CF1和CF3与双马树脂的界面剪切强度较高,表明上浆剂与双马树脂间的化学反应程度是影响其界面粘结性能的主要因素。该研究结果对我国碳纤维上浆剂的研制具有参考价值。     

X射线脉冲星导航硬件脉冲轮廓累积研究

为了在X射线脉冲星地面实验系统仿真源模拟产生X射线的基础上,能够快速稳定地得到脉冲轮廓,采用硬件历元叠加的方法获得脉冲轮廓。研究了用硬件实现历元叠加及其数据整合的算法,该算法首先在MATLAB现场可编程逻辑阵列(FPGA)中实现,再通过MATLAB硬件描述语言(HDL)代码生成模块把算法转换成HDL,经编译后获得配置硬件的Bit文件,最终在开发板FPGA上实现数据处理的硬件模块。一段时间内的光子到达时间数据通过MATLAB算法得到的脉冲轮廓数据与通过硬件模块处理后得到的数据结果存在误差,在单个时间窗口内误差最大值为2个光子数,误差平均值占光子数统计平均值的0.084%;两组统计的脉冲轮廓数据中不同数据占总数据个数的9.481%,这样的误差不影响后端模拟导航模块的导航。利用硬件实现的历元叠加及其数据整合模块具有处理速度快、设备紧凑、功耗低的特点,为航天器利用X射线脉冲星导航提供了一种可行的硬件数据处理技术上的支持。