全文获取类型
收费全文 | 775篇 |
免费 | 312篇 |
国内免费 | 23篇 |
专业分类
航空 | 688篇 |
航天技术 | 82篇 |
综合类 | 26篇 |
航天 | 314篇 |
出版年
2024年 | 11篇 |
2023年 | 19篇 |
2022年 | 26篇 |
2021年 | 31篇 |
2020年 | 22篇 |
2019年 | 36篇 |
2018年 | 23篇 |
2017年 | 23篇 |
2016年 | 29篇 |
2015年 | 21篇 |
2014年 | 25篇 |
2013年 | 30篇 |
2012年 | 49篇 |
2011年 | 40篇 |
2010年 | 35篇 |
2009年 | 34篇 |
2008年 | 44篇 |
2007年 | 33篇 |
2006年 | 28篇 |
2005年 | 24篇 |
2004年 | 26篇 |
2003年 | 25篇 |
2002年 | 24篇 |
2001年 | 35篇 |
2000年 | 29篇 |
1999年 | 31篇 |
1998年 | 44篇 |
1997年 | 27篇 |
1996年 | 40篇 |
1995年 | 36篇 |
1994年 | 27篇 |
1993年 | 26篇 |
1992年 | 24篇 |
1991年 | 34篇 |
1990年 | 21篇 |
1989年 | 20篇 |
1988年 | 18篇 |
1987年 | 14篇 |
1986年 | 7篇 |
1985年 | 5篇 |
1984年 | 4篇 |
1983年 | 3篇 |
1982年 | 4篇 |
1981年 | 1篇 |
1980年 | 2篇 |
排序方式: 共有1110条查询结果,搜索用时 46 毫秒
71.
以超临界压力正癸烷为工质,在内径2mm的竖直圆管内进行了不同工况条件下的流动与换热不稳定性实验研究。实验发现两种原理的不稳定性现象。转捩型是由于流动状态由层流向湍流转变引起,多为随机的小幅震荡,约在Re=5000左右出现;物性型由准临界温度附近剧烈变化物性所致,具有较大振幅和固定周期,约8~15s。增强系统稳定性的方法主要包括提高进口流体温度、升高压力或者采用向下流动方式。实验还发现在振荡区间内存在稳定区间现象。 相似文献
72.
73.
高超声速飞行在广义上可泛指在大气层中马赫数大于5的飞行。在这个意义上,飞船、航天飞机(包括美国的X-37B)、导弹的再入段,都有一段是高超声速飞行,包括它们的上升段,也有一段是高超声速飞行,但它们都没有进行高超声速巡航,遇到的问题相对简单。在本文中我们着重讨论用吸气式发动机在大气层中进行高超声速巡航的飞行器,以及用火箭助推到高空然后滑翔 相似文献
74.
详细介绍了制定行星际探测中途修正策略的Breakwell间距比法,给出了在燃料最优条件下,终端误差精度和制导能力与中途修正设计次数和时刻之间的解析关系。一般而言,终端误差精度每提高3倍,修正次数就需要增加1次,制导能力每提升3倍,修正次数就可以减少1次。在具体使用上,应首先根据精度要求和制导能力确定最后一次修正时刻,然后向前递推,使得前一次修正后误差传播量与后一次修正后误差传播量成公比为1/3的等比数列,以此确定其余修正时刻,从而保证在达到终端精度前提下,整体燃料消耗最少。以火星探测为例,给出探测器于2018年5月出发12月达到火星的算例,仿真结果表明了理论分析的正确性。 相似文献
75.
76.
今年1月6日,美国航空环境公司研制的"全球观察者"(Global Observer)无人机在爱德华空军基地成功地完成了以氢燃料为动力的首次飞行,标志着"联合能力技术验证"(JCTD)计划的验证与使用功效阶段工作的正式启动.该公司凭借在液氢燃料关键技术方面所取得的突破,放弃了长期探索的太阳能动力方案,转而采用氢燃料动力... 相似文献
77.
78.
月面远程运输飞行轨迹优化设计 总被引:1,自引:0,他引:1
针对月球表面不同区域之间的载人或载货运输问题,设计了一种基于上升-巡航-下降模式的燃料最省飞行轨迹。首先通过求解不同飞行时间的Lambert问题确定了最佳飞行时间,并获得了对应的双脉冲解,然后利用有限推力替代两次速度脉冲,建立了非线性规划问题,求解得到了有限推力燃料最省飞行轨迹。优化设计过程中主要研究了两个主要难点:bang-bang控制与飞行高度约束。这两个问题通过推力加速度与飞行时间的数值延拓得以解决,同时揭示了月面飞行的基本原理。最后给出了3种不同应用场景的仿真算例,仿真结果表明,当飞行时间为小时量级时,上升-巡航-下降飞行模式下的优化解即为燃料最优解,如果飞行距离较远,则还需要适当增加飞行时间从而满足飞行高度约束。 相似文献
79.
LUO Cheng LIU Hua YANG Jia-ling LIU Kai-xin 《中国航空学报》2007,20(3):230-235
Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks. 相似文献
80.
Wu Xianyu Li Xiaoshan Ding Meng Liu Weidong Wang Zhenguo 《中国航空学报》2007,20(6):488-494
In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances. 相似文献