A comprehensive survey on the methods of angle of attack measurement and estimation in UAVs

Angle of Attack (AOA) is a crucial parameter which directly affects the aerodynamic forces of an aircraft. The measurement of AOA is required to ensure a safe flight within its designed flight envelop. This paper intends to summarise a comprehensive survey on the measurement techniques and estimation methods for AOA, specifically in Unmanned Aerial Vehicle (UAV) applications. In the case of UAVs, weight constraint plays a major role as far as sensor suites are concerned. This results in selecting a suitable estimation method to extract AOA using the available data from the autopilot. The most feasible and widely employed AOA measurement technique is by using the Multi-Hole Probes (MHPs). The MHP measures the AOA regarding the pressure variations between the ports. Due to the importance of MHP in AOA measurement, the calibration methods for the MHP are also included in this paper. This paper discusses the AOA measurement using virtual AOA sensors, their importance and the operation.     

Influence of thickness and initial groove angle in M–K model on limit strain of 7B04 by considering through-thickness stress

Marciniack–Kuczinski (M–K) model is widely used to predict material’s forming limit curve (FLC). The prediction of FLC traditionally neglected through-thickness normal stress. However, it cannot be neglected in some forming processes. Much work has been done to study the effect of through-thickness normal stress on FLC with constant through-thickness normal stress or constant ratio of through-thickness normal stress and maximum principal stress. In addition, based on Nakazima test process, the ratio of through-thickness normal stress and maximum principal stress has been derived, which was a function of instantaneous thickness and loading path. Here, initial groove angle in M–K model was not considered. In this paper, uniaxial tension tests and Nakazima tests were performed on 7B04 aluminum alloy. Based on Hill 48 yield criterion and M–K model, the prediction model of FLC was established. The increase of thickness can enhance FLC. Meanwhile, it is necessary to consider through-thickness normal stress and initial groove angle in prediction model. On the left side of FLC, the effect of initial groove angle on FLC is weakened by increasing sheet thickness. On the right side of FLC, the effect of initial groove angle on FLC is strengthened by increasing sheet thickness. On the right side of FLC, the relation between limit strain points with different thicknesses is linear under one certain loading path. Thickness has decisive effect on through-thickness normal stress level and the changing trendy of through-thickness normal stress during calculation is different under different stress condition.     

薄膜充气管充气展开特性试验

用展开导轨消除因重力产生的摩擦力,在不同充气速率与初始展开角条件下对薄膜材料充气管的充气展开特性进行了试验研究,获得了展开角,以及展开加速度和内气压的变化规律。试验及分析结果表明:充气管的充气膨胀与展开相互独立,充气膨胀过程近似为等压增容过程,折叠部位的气压变化特性与整体气压变化特性差异明显。     

求解含多个右端向量非对称线性方程组的自适应块拟最小残量IOM(q)算法

许多实际应用问题需要求解含多个右端向量的大型非对称线性方程组 ,通常是把原来方程组分成单独几个含一个右端向量的方程组 ,再用某种迭代法分别单个求解 ,而更加经济有效的方法是应用能同时产生几个迭代向量的块迭代法来直接求解。本文在 IOM(q)算法的基础上 ,提出一种求解此类方程组的块拟最小残量 IOM(q)算法 ,讨论了如何收缩掉已收敛的部分方程组以及如何从产生的块 Krylov序列中删除线性相关或几乎线性相关向量的自适应技术。数值试验表明 ,此新的自适应块算法比块 GMRES算法及其他相关算法具有更好的收敛行为、更少的计算量和 CPU计算时间 ,是求解此类方程组的一种更加经济有效的算法。     

卫星推进及控制装置准直测量方法研究

在传统的卫星推进及控制装置准直测量方法的基础上,提出两种新的测量方法,即小角度准直测量法和三维坐标准直测量法,并给出了相应的数据处理方法。所提出的方法测量精度高、测量速度快,无需转台整平,也不必对转台上的定位销进行精确准直。     

错位与缺失

性权利是人类自然权利和社会权利的集合体,大学生拥有性权利是无可辩驳的事实。分析部分大学生漠视性隐私权、性教育权,只关注性自由权、性快乐权和自主选择权的原因,会发现其性价值观的错位和义务观的缺失是主要根源,加之媒体的不当报道也起到了推波助澜的作用。这样的现实要求我们必须加强大学生性权利的伦理教育以及性权利与性义务的对等教育。     

基于分段常滑翔角的长航时纵向远程滑翔飞行方程近似解

提出用包含地球旋转效应的n个常滑翔角飞行段近似实际滑翔飞行轨迹的方法。基于该方法推导了长航时纵向远程滑翔飞行轨迹近似解，并给出了各段常滑翔角、滑翔时间的求解方法及整个滑翔轨迹近似计算步骤。文中算例结果表明，该近似求解方法计算得到的滑翔航程和滑翔时间与实际值相差很小，航程误差率约为0．7％，时间误差率约为0．6％，因此该方法在近似小初始滑翔角的长航时远程纵向滑翔飞行时是有效的、可行的，尤其针对航程在地球半圈以上的滑翔飞行轨迹。     

基于一维相控阵引信的起爆控制算法研究

工程上实现最佳引战配合要求导弹战斗部最大破片密度方向瞄准目标要害部位。基于一维相控阵引信的波束控制技术,推导了最佳起爆角和起爆延时算法,并研究了一种改进卡尔曼滤波方法在此算法中的应用。该滤波算法将球坐标系中导弹导引头的测量信息转换到直角坐标系下进行滤波,同时消除了由于坐标转换而引起的偏差。仿真结果表明,该滤波算法的应用能得到很高的最佳起爆角和起爆延时估计精度。     

多层RAM涂层对任意入射角电磁波的反射特性分析

为了解决结构型吸波材料的分析和设计中所遇到的反射系数计算问题，从电磁场理论出发，导出了电磁波以任意角入射时多层雷达吸波材料（RAM）涂层的反射系数公式，此法简单易行，为结构型吸波材料的计算机辅助分析和设计提供了基础，同时给出了计算曲线的例子，通过实例计算分析了电磁波的入射角，极化状态等对反射特性和隐身效果的影响。