钛合金表面抗激光涂层损伤特性及热效应影响研究

实验研究了钛合金和高反射型陶瓷涂层材料抗连续型激光烧蚀的损伤及温度分布特性，并从热效应影响角度对比分析了二者在抗激光损伤效果方面的差异性。研究结果表明：相比于钛合金，高反射型陶瓷涂层材料能有效增强钛合金基底抗激光损伤的能力；在同等激光功率密度辐照下，陶瓷涂层材料能有效提升钛合金基底耐受激光辐照的时间长度。实验结果表明该陶瓷涂层材料的激光损伤阈值比钛合金高约5.8倍。实验发现陶瓷涂层温升速率高于钛合金，但由于陶瓷材料具有较高的反射特性，以及良好的热吸收和热传导特性，因此能使由激光辐照产生的热量在其表面较快地扩散，而降低向基底方向传导的程度，最终提升陶瓷涂层的抗激光损伤阈值。     

A progressive approach to predict shot peening process parameters for forming integral panel of Al7050-T7451

In this paper, a progressive approach to predict the multiple shot peening process parameters for complex integral panel is proposed. Firstly, the invariable parameters in the forming process including shot size, mass flow, peening distance and peening angle are determined according to the empirical and machine type. Then, the optimal value of air pressure for the whole shot peening is selected by the experimental data. Finally, the feeding speed for every shot peening path is predicted by regression equation. The integral panel part with thickness from 2 mm to 5 mm and curvature radius from 3200 mm to 16000 mm is taken as a research object, and four experiments are conducted. In order to design specimens for acquiring the forming data, one experiment is conducted to compare the curvature radius of the plate and stringer-structural specimens, which were peened along the middle of the two stringers. The most striking finding of this experiment is that the outer shape error range is below 3.9%, so the plate specimens can be used in predicting feeding speed of the integral panel. The second experiment is performed and results show that when the coverage reaches the limit of 80%, the minimum feeding speed is 50 mm/s. By this feeding speed, the forming curvature radius of the specimens with different thickness from the third experiment is measured and compared with the research object, and the optimal air pressure is 0.15 MPa. Then, the plate specimens with thickness from 2 mm to 5 mm are peened in the fourth experiment, and the measured curvature radius data are used to calculate the feeding speed of different shot peening path by regressive analysis method. The algorithm is validated by forming a test part and the average deviation is 0.496 mm. It is shown that the approach can realize the forming of the integral panel precisely.     

固体推进剂燃烧中凝相粒子的激光全息测试

概述了测试凝相粒子尺寸的基本方法，较详细地阐述了研究燃烧场凝相粒子尺寸分布的激光全息测量方法和测试结果。     

空气压强对激光推进器冲量耦合系数影响

设计并加工了激光推进器实验模型,以空气为推进工质,利用脉冲式CO2激光器,研究了空气压强对激光推进器冲量耦合系数影响。实验结果表明,空气压强对激光推进器性能有显著影响。在文中实验条件下,当空气压强大于6 kPa时,激光推进器冲量耦合系数随压强减小而减少较慢;当空气压强小于6 kPa时,激光推进器冲量耦合系数随压强减小而减少很快。     

钛合金板材激光弯曲成形的研究

 对常温下钛合金板材进行了激光弯曲成形研究。分析了激光功率、扫描速度、光斑大小对板材弯曲变形的影响,获得理想工艺参数范围为:功率1 .0～1 .2 k W、扫描速度2～3 m/min、光斑直径6～7mm。同时分析了板材厚度、宽度及扫描次数对材料弯曲变形的影响,为钛合金板材弯曲成形提供了一种新途径。     

联合制导攻击武器六自由度系统仿真

重点分析了GPS/IN S复合制导系统及激光导引头的工作原理和建模方法,同时介绍了增程套件的原理,并设计了方案弹道。通过六自由度弹道仿真,比较了增加组件前后联合制导攻击武器的性能指标。研究结论对我国现有库存常规炸弹的制导化改进有一定的参考价值。     

激光陀螺及其误差补偿

 本文介绍国外研制环形激光陀螺(RLG)的经验和现状,把误差产生机理及其补偿方法作为研究重点,这是取得成果的基础。机械抖动偏频技术有优点,得到了广泛应用,但在精度上尚不能满足精密惯性导航的要求。近年来国外正在研究的速率偏置技术显著地降低了RLG的随机误差,并可补偿常值漂移。本文讨论了这一技术的优点。     

高能CO2激光腔镜高反介质薄膜的传输特性

为了获得适用于高能CO2激光器的高抗破坏阈值高反薄膜,以10.6μm高反膜ZnSe/YbF3,PbTe/BaF2膜系为例,数值模拟了激光在高反介质膜中的传输的场特性;给出了激光在多层介质膜中的场强分布、温度场分布及热应力分布。结果表明硅镜基体上的PbTe/BaF2膜系所需膜层厚度小、膜层数少,反射率可高达99.98%。     

测量透明位相物场的激光纹影-散斑干涉系统(英文)

本文给出了诊断相位场,如燃烧、对流、自由射流、超声速流场和等离子体等的一种激光纹影-散斑干涉系统。利用这套光学系统可在同一瞬时获得流场的散斑图和与之相应的剪切干涉图。作为实验,对一非定常波动的火焰(本生灯)进行了测试,实验表明用散斑照相术有可能得到密度波动的湍流场的定量结果;作为定量测试,对一沿竖直平板的自然对流,同时应用散斑照相和差纹影干涉术进行了定量分析,其结果的一致性很好。本文最后给出了散斑图的傅氏变换空间滤波的全场类似子纹影干涉图的流场显示照片。