Partition method for improvement of piecewise linear model with full envelope covered

Since ambient conditions vary in a wide range within the full flight envelope, the existing piecewise linear model (PLM), which is based on sea-level static condition with use of corrected parameters for other points in the flight envelope, cannot meet the accuracy for replacing the nonlinear model. To obtain more accurate linear models, a method of partitioning the flight envelope over a grid of Mach number and altitude boxes was suggested. Then, a set of linear models for a given operating condition was selected by picking the nearest (Mach number, altitude) box in the flight envelope. Through the selected set of linear models, interpolating for power level based on a weighted sum of corrected rotor speeds can obtain a linear model with acceptable accuracy. Simulation results of different points within the full flight envelope showed that the maximum error between nonlinear model and the existing PLM was more than 50%, while the maximum error between nonlinear model and the improved PLM was within 8%. It is concluded that the improved PLM performs accurately, especially under the non-standard conditions. In addition, the improved PLM can satisfy the real-time requirement better than the existing PLM.      

钇对Ti-23Al-25Nb合金压缩性能的影响

采用SEM和XRD分析热处理后合金试样的显微组织及相组成,用TEM分析原始组织中钇的存在方式.结果表明,钇在原始组织中以Y2O3形式存在;钇增加O相衍射峰,提高Ti-23Al-25Nb合金压缩性能,如抗压强度、压缩率等,钇的强化作用是由于Y2O3第二相粒子强化和钇细化晶粒的晶界强化共同作用的结果.     

金属屑信号器壳体腐蚀修复技术研究

针对某型发动机金属屑信号器壳体腐蚀情况，分析了传统修复方法的缺陷，提出了机加胶接复合修复技术的新思路，确定了修复中所选用的金属和非金属材料，并介绍了修复工艺。     

502胶在常温应变电测中的应用

对在常温应变电测中,502胶影响测试精度的因素进行了分析;结合基础试验研究,指出了在静、动态应变电测中使用502胶时的注意事项.     

俄罗斯的航空用胶和粘性材料

介绍了俄罗斯的各种航空用胶及粘性材料的研制和现状。     

复合材料孔边分层灌胶修理强度恢复能力研究

分层缺陷是复合材料常见的缺陷之一,对灌胶修理复合材料强度恢复进行研究。基于2DHashin失效 准则,以线性准则描述其损伤演化过程,利用ABAQUS/Standard模块进行非线性分析,研究碳纤维复合材料的孔边分层缺陷,采用灌胶修理后,对分层区域重新建立Cohensive单元,分析碳纤维复合材料强度恢复能力。结果表明:复合材料孔边分层对拉伸强度、压缩伸强度几乎无影响;随着钉载比的增大,拉伸极限载荷会有一定程度的降低;随着钉载比的增大,压缩极限载荷会有一定程度的降低;灌胶修理后,孔边分层的屈服载荷可恢复到无损状态;随着钉载比的增大,屈服极限载荷会有一定程度的增大。     

The solar-terrestrial event of 23 February 1956

The solar flare of 23 February 1956 and the resulting geophysical disturbance ranks as one of the most remarkable solar-terrestrial events of the twentieth century. It sparked many papers and has seldom been equalled. Fifty years after the International Geophysical Year, it seems timely to review the observations of the event from today’s perspective, and to draw on the recollections of scientists who were active at the time.     

应力对DD5单晶高温合金持久过程中析出相的影响

利用扫描电镜和透射电镜研究了DD5单晶高温合金在持久性能测试过程中试样不同位置析出相的析出规律,分析了应力对析出相析出行为的影响并鉴定了两种析出相的种类。研究结果表明该合金在1 038 ℃/172 MPa条件下随着局部拉应力的增大,枝晶间和枝晶干析出相数量都明显增加;合金在871 ℃/552 MPa条件下只在枝晶间区域析出少量粒状析出相,且随拉应力的增大,析出相数量有所增加;透射电镜分析表明合金的枝晶干区域的析出相主要为μ相,枝晶间析出粒状析出相主要为M₂₃C₆碳化物相。     

降低航炮后座力的必要性及可行性

航空射击武器的后座力对其载机有诸多不利影响,因此,必须设法减小这些影响。本文就JL8飞机航炮后座力过大对飞机的不利影响进行了分析,阐述了降低航炮后座力的必要性。同时还就如何解决航炮后座力过大问题进行了研究,提出了降低JL8飞机所装23－2航炮后座力的方法。     

稀土对高纯超高强度23CoNi钢组织与性能影响的初步探索

在23CoNi钢中添加稀土可改善δ5和ψ,抗拉强度σb和冲击值aku略有提高,而对KIC和σ0.2影响较小.添加稀土后钢中形成含S和Al稀土化合物.研究表明,稀土可阻碍钢的晶粒长大,并能细化板条马氏体的板条尺寸.