A progressive approach to predict shot peening process parameters for forming integral panel of Al7050-T7451

In this paper, a progressive approach to predict the multiple shot peening process parameters for complex integral panel is proposed. Firstly, the invariable parameters in the forming process including shot size, mass flow, peening distance and peening angle are determined according to the empirical and machine type. Then, the optimal value of air pressure for the whole shot peening is selected by the experimental data. Finally, the feeding speed for every shot peening path is predicted by regression equation. The integral panel part with thickness from 2 mm to 5 mm and curvature radius from 3200 mm to 16000 mm is taken as a research object, and four experiments are conducted. In order to design specimens for acquiring the forming data, one experiment is conducted to compare the curvature radius of the plate and stringer-structural specimens, which were peened along the middle of the two stringers. The most striking finding of this experiment is that the outer shape error range is below 3.9%, so the plate specimens can be used in predicting feeding speed of the integral panel. The second experiment is performed and results show that when the coverage reaches the limit of 80%, the minimum feeding speed is 50 mm/s. By this feeding speed, the forming curvature radius of the specimens with different thickness from the third experiment is measured and compared with the research object, and the optimal air pressure is 0.15 MPa. Then, the plate specimens with thickness from 2 mm to 5 mm are peened in the fourth experiment, and the measured curvature radius data are used to calculate the feeding speed of different shot peening path by regressive analysis method. The algorithm is validated by forming a test part and the average deviation is 0.496 mm. It is shown that the approach can realize the forming of the integral panel precisely.     

Review and propositions for the sliding/impact wear behavior in a contact interface

A thermal-solid-liquid complex operational environment induces structural interface developing a typical coupling sliding/impact wear behavior. It results in contact damage until systems fail, which may cause significant economic losses and catastrophic consequences. The key point of solving this problem is to reveal the coupling damage mechanism of the sliding/impact behavior in typical systems and life characterization under a complicate evolving environment. This has been a hot topic in the area of mechanical reliability. The main work in this paper can be concluded as follows. Firstly, the main industries in which the “sliding/impact behavior” takes place have been introduced. Then, existing studies on the wear mechanism and degree analysis are presented, which includes surface morphology analysis, wear debris analysis, and wear degree measurement. Meanwhile, existing problems in theoretical modeling and experiments in current research are summarized, so as to point out a bright direction for future research on wear prediction. They include interface contact modeling, mathematic coupling mechanism modeling, wear equation establishment, and wear life characterization, which can provide some new ideas for improving the existing studies on the sliding/impact wear behavior.     

历经十年寿命试验的消旋天线机构轴承的可靠性分析

解决了一个计算可靠性问题的特例。分析了消旋天线机构轴承历经10年寿命试验的可靠性问题。并给出了轴承在不同可靠寿命要求下的可靠度(对应不同置信度)。     

复杂系统的可靠性分析方法研究

本文对未来的运载器的复杂控制系统的可靠性建模、分配和预计的一般方法和程序及综合分析方法进行了讨论和研究。并简述了复杂系统的计算机辅助可靠性分析。     

门限自回归模型参数的局部正交设计寻优法

在采用点值图确定门限区间个数的基础上，对门自回归模型中门限值、滞后步长、各门限区间模型阶数，利用正交设计方法寻优，计算工作量锐减，却可得到精度较高的预报模型。     

一种基于移步预测消除脉冲串扰的快速算法

以毫米波主被动复合探测器为工程应用背景,通过分析信号的特点,提出一种基于移步预测思想的快速算法来消除脉冲调制信号对被动通道信号的串扰。仿真分析和实验结果表明,该方法对改善信噪比效果明显,而且具有成本低、速度快和易于工程化实现的优点。     

正态分布可靠寿命经典近似限的改进

本文给出了正态分布可靠寿命的又一个经典近似下限，经验证，本文所给出的结果的精度比已有的结果精度要高，可提供给可靠性工程人员使用。     

电子设备可靠性预计参数综合分析方法研究

如何调整元器件的参数以满足可靠性要求并达到最佳的效费比?传统的方法是绘制故障率随单个预计参数变化的曲线，然后根据变化的趋势分别进行调整，但该方法很难直观地反映出多参数对故障率的综合影响，为了达到优化的目的，设计人员需要根据经验反复地调整各类参数。为此，本文结合电子产品可靠性预计软件，给出了直观分析各参数对电子设备可靠性预计结果综合影响的方法。     

多传感器数据融合与弹道落点的预报

为了更精确地对弹道落点进行预报，对多传感器数据融合技术进行了,分批人出了雷达、红外系统和光测系统与传感器融合子系统连用的实例，并得出结论：单传感器的精度是难以满足现代战争需要的，寻求一种较好的融合方法来提高落点预报精度虽是一个难题，但仍是可行的。     

遥测系统可靠性模型及评定方法

本文根据遥测系统的实际背景和特点,认为遥测系统适合采用K/N(G)模型。并就由指数寿命型不同元件组成的K/N(G)模型,应用并推广了R.G.Easterling方法,使遥测系统的可靠性分析与设计变得行之有效。