涡扇发动机低压部件通流耦合计算

为了研究各部件匹配与过渡段几何参数对发动机总体性能的影响,针对某涡扇发动机风扇、低压涡轮、内外涵道、掺混段和尾喷管等部件,基于周向平均Navier-St okes通流控制方程,采用时间推进有限体积法进行了部件耦合计算求解,将沿程各部件性能计算参数与试验做了对比,结果表明:在设计状态下发动机沿程各截面计算特征参数与试验值最大误差不超过5.0%,说明该通流耦合计算方法能够快速预估发动机总体性能,完善各部件匹配关系,在发动机总体设计初期有一定工程应用价值。     

多电飞机主发电机供电条件模拟装置设计

多电飞机主发电机要接入电网向电网供电,须要满足很多条件。首先要使准备接通的发电机励磁,然后当发电机转速正常,发电机电压达到要求后,并在外电源已经断开的条件下,接通发电机接触器,使发电机向电网供电。设计基于C8051单片机及外围电路的装置,对多电飞机主发电机接入电网的控制条件进行模拟,并将结果显示在装置的LCD(Liquid Crystal Display,简称LCD)显示屏上。该装置的设计包括硬件电路设计和软件程序编写。最后对装置进行调试与验证,实验结果能够达到设计初衷。     

民机电传飞控系统CCAR 25.672符合性验证思路研究

首先阐述民机电传飞控系统适航符合性验证的定义,然后详细介绍了民机电传飞控系统适航符合性方法和选用原则,最后以国内某型民用客机为研究对象,开展了针对CCAR25.672条款的符合性验证思路的分析与研究。     

基于直升机舰面起降动态仿真的风限图计算

建立了基于直升机舰面起降动态仿真的风限图（WOD）计算方法,综合计入舰船尾流、直升机运动和驾驶员操控等多因素的作用提升风限图计算的准确度。基于耦合舰船非定常尾流的飞行动力学模型,发展了适于直升机多轴协同操控的驾驶员模型,建立了舰面起降轨迹的数学描述和生成方法,形成计入舰船尾流、直升机运动和驾驶员操控等多因素综合作用的直升机舰面起降动态仿真方法。在此基础上,总结风限图计算判据,建立风限图计算方法。计算结果表明,某些风况下直升机在舰面起飞和降落过程中受到舰船尾流的干扰远大于在甲板上方悬停时受到的作用。本文方法能够捕捉到不同起降点和起降方式导致舰船尾流时空变化的干扰,与传统计算方法相比,显著提升了风限图计算的准确度。     

计及弹射滑车质量的某舰载无人机弹射动态响应分析

舰载无人机是未来海上作战的关键装备,其弹射动态性能严重影响起飞安全。弹射滑车与舰载机起落架弹射杆相连,在牵制杆突卸弹射滑跑过程中共同组成一个耦合动力学系统。目前,国内外尚缺乏对此耦合系统动力学特性的研究。以由某无人机改造的弹射型为研究对象,建立了包含弹射滑车质量的弹射动力学模型,并开展了拖拽弹射过程的动态响应分析,结果表明：弹射滑车的惯性力会沿着弹射杆传递到前起落架上,拖拽弹射过程中前起落架载荷波动幅度增大,前起落架撑杆、弹射杆以及前轮垂向载荷峰值分别增加了23.4%、21.6%和14.0%;前起落架缓冲器压缩量变化范围扩大了30.4%;前起落架纵向和垂向的载荷振荡频率分别从90.9 Hz和5.2 Hz降到26.3 Hz和4.4 Hz。     

径向磁气组合轴承系统的动态性能

为探究磁轴承失效时能否减轻转子跌落带来的损害,将人字槽径向动压气体轴承引入磁轴承转子系统,研究磁气组合轴承对系统动态性能的影响和动压气体轴承的支承特性。采用有限差分法和小扰动法求解气膜厚度方程和雷诺方程,研究动压气体轴承的静动态特性。对磁轴承电磁力进行了分析,采用磁轴承不完全微分PID（比例-积分-微分）控制策略,对系统进行了理论模态分析和试验模态分析,完成了系统高速旋转试验,测试了动压气体轴承在不同偏心率和转速下的承载力。结果表明,引入动压气体轴承可提高系统的动态性能,在磁轴承失效造成高速转子跌落瞬间,偏心率趋近于1,两个径向动压气体轴承能够产生较大承载力,减轻转子跌落造成的损害。      

Time delay compensation in lateral-directional flight control systems at high angles of attack

The previous studies of time delay compensation in flight control systems are all based on the conventional aerodynamic derivative model and conducted in longitudinal motions at low angles of attack. In this investigation, the effects of time delay on the lateral-directional stability augmentation system in high-α regime are discussed based on the $\dot{\beta }$ model, which is proposed in our previous work and proved as a more accurate aerodynamic model to reveal the lateral-directional unsteady aerodynamic characteristics at high angles of attack. Both the $\dot{\beta }$ model and the quasi-steady model are used for simulating the effects of time delay on the flying qualities in high-α maneuvers. The comparison between the simulation results shows that the flying qualities are much more sensitive to the mismatch of feedback gains than the state errors caused by time delay. Then a typical adaptive controller based on the conventional dynamic derivative model and a gain-prediction compensator based on $\dot{\beta }$ model are designed to address the time delay in different maneuvers. The simulation results show that the gain-prediction compensator is much simpler and more efficient at high angles of attack. Finally, the gain-prediction compensator is combined with a linearized $\dot{\beta }$ model reference adaptive controller to compensate the adverse effects of very large time delay, which exhibits excellent performance when addressing the extreme conditions at high angles of attack.     

Inertial parameter estimation and control of non-cooperative target with unilateral contact constraint

In this paper, the relative sliding motion between the target and the manipulator’s end-effector is considered and characterized as a unilateral contact constraint. A new possible solution is presented to estimate the inertial parameters of a non-cooperative target while the relative sliding motion exists. First, the detailed analysis of the dynamical model is presented, and a parameter-explicit linear time-varying model is obtained. Then, an extended state observer is constructed based on the new model, which can effectively estimate the unknown inertial parameters of the target when relative sliding motion exists. As the modified reactionless controller requires the knowledge of inertial parameters, a hybrid post-capture control scheme is also established based on the switch law between different controllers. The correctness and efficiency of the proposed algorithm are validated by numerical simulation, which proves a potential framework for the non-cooperative target post-capture operation.     

Modeling and experiment of grinding wheel axial profiles based on gear hobs

Hobbing is one of the crucial gear manufacturing processes with high precision and high efficiency. In order to improve the accuracy of hobbing and hob relief grinding, more precise grinding wheels are demanded for relief grinding in the production of gear hobs. In this paper, a new and accurate mathematical method for calculating the axial profile of grinding wheel based on the corresponding gear hob to be ground is proposed. Considering that most researches have been conducted to focus on the optimization of hob geometric feature and only can be applied to a specific type of hand of helix and rake angle of gear hobs. The method in this paper can be served as a general algorithm for generating axial profile of grinding wheels on the basis of the spatial envelope theory, the principle of coordinate system transformation, and studies on normal profile of single-tooth. The accuracy of grinding hobs is based on applying the approach in practical manufacturing. Taking two typical different kinds of pre-grinding gear hobs as examples for calculation and experiment, the results of tooth profile errors strengthen the position that the validity and feasibility of this method, it can be employed for gear hob design and grinding processing.     

扇翼飞行器的研究进展与应用前景

随着科学技术的迅猛发展,飞机无论在构型还是性能方面都获得了飞速发展,但是新原理飞机的研制却进展不大。扇翼飞行器是近期发展起来的低速大载荷新型飞行器,它是不同于现有固定翼、旋翼飞行器的新构型、新原理飞行器。而国内对于该飞行器的研究才刚刚起步,可参考的文献资料很少。因此,本文通过国内外扇翼飞行器发展状况的研究,对扇翼飞行器研究进展进行总结分析。首先介绍了扇翼飞行器的飞行原理;其次系统地回顾了扇翼飞行器的提出,并总结了其在国内外研究的进展情况;接着根据扇翼飞行器近期的发展动态,对该飞行器的应用前景作出分析;最后总结了扇翼飞行器发展中亟待解决的关键技术,以及其未来发展的难点和趋势。