脉动背压离心压气机动态特性及稳定性

试验研究了脉动背压对离心压气机动态响应及喘振特性的影响规律。结果表明:脉动背压条件时压气机性能存在明显非定常特征,高频大幅脉动背压和陡峭的压比流量特性均可强化该非定常特征。基于试验结果,提出了脉动背压压气机非定常性能与脉冲特性及运行工况的关联模型。脉动背压导致压气机喘振边界左移,稳定运行范围最高拓宽12.3%。压气机向小流量工况趋近时,脉动背压引起的流场振荡减弱,但喘振所致的流场振荡逐步强化,致使流场振荡强度呈V型变化特征,表明了脉动背压与压气机气动稳定性之间存在耦合关系。研究探明了脉动背压条件对压气机动态响应和喘振特性的影响规律,对帮助真实运行环境压气机设计理论的发展具有重要意义。      

Advanced flight management system human interface

Alternative Flight Management System (FMS) human interface concepts are becoming increasingly important to investigate as the complexities of understanding and operating this equipment continue to burden and confuse an already inundated pilot. Rockwell Collins, Inc. has designed an advanced FMS display/interface that will significantly reduce and/or eliminate human interface problems between users and the FMS. Results from human factors investigations for a limited set of FMS functions reveal statistically significant findings at the 95th level of confidence favoring the Advanced FMS Interface display format. The Advanced FMS Interface display format produced quicker reaction times and lower levels of mental workload than the a conventional Control Display Unit (CDU) type FMS.Furthermore, statistically significant findings at the 98th level of confidence for three subjective measures, Usability, Learnability, and Overall Attitude lean in favor of this type of FMS display format. These statistically significant findings lead us to believe that this Advanced FMS Interface display format has great potential for significantly reducing and/or eliminating human interface problems between users and the FMS while at the same time reducing pilot mental workload.     

The demography of massive galactic black holes

This review describes dynamical evidence for massive black holes (BHs) at the centers of galaxies. BHs appear to be a common if not ubiquitous feature of local galactic spheroids, with a mean mass that is roughly 0.5% of the parent stellar spheroid mass. This mass is large enough that the formation and evolution of central BHs has had a significant influence on the inner stellar density profile. For example, low-density, core-type profiles may have been created by the scouring action of binary BH pairs, whose orbital decay ejects stars from the center of the galaxy. Or, BHs may have grown substantially by gas accretion, pulling in surrounding stars and creating the cuspy cores and power laws that are seen in spheroids. If BHs are ubiquitous in galactic spheroids at the above mass ratio, their total local mass density is comparable to that implied by the energy density of QSO photons, suggesting that these local BHs are the long-sought fossil BHs of QSO central engines. However, QSOs are much rarer per unit co-moving volume than local BHs, unless one equates them to just the massive BHs found in rare and massive local spheroids. The resultant BH masses exceed typical QSO BH mass estimates by nearly a factor of 10, suggesting that BHs have grown in mass by roughly that factor since the QSO era. At least some of that growth might have occurred as protogalaxies grew in mass by mergers, and their BHs also merged and grew apace.     

Impulsive plasma waves observed by DE-1 in the magnetosphere

Impulsive plasma waves (1–9 kHz) with durations less than 100 msec have been found in DE-1 wide-band electric field data (650 Hz – 40 kHz) received at Kashima, Japan. The waves are associated with a strong narrow-band ELF hiss, and were observed at geocentric distances from 3.1 to 4.9 Re (earth's radius) in the low-latitude nightside magnetosphere. Local electron densities and plasmapause locations estimated suggest that the waves were observed outside the nightside plasmapause. The waves are discussed in terms of Landau resonant trapping of magnetospheric electrons by the associated whistler-mode ELF hiss.     

目标机动条件下的定点伴飞控制方法研究

对目标机动条件下的定点伴飞控制进行了研究。根据相对运动关系,建立适于伴飞模式的相对运动方程,将目标机动大小作为未知量加入相对运动方程,构建不确定系统。用LQR和Lyapunov法结合的方式设计相应定点伴飞控制律。理论证明了在目标机动时该控制律仍能实现系统的渐近稳定。仿真结果验证了该控制律的有效性。     

“汽电双驱”系统电机瞬态性能仿真研究

以上海电机厂有限公司“汽电双驱”项目中三相异步电动机/发电机为依据,基于以Ansoft软件,利用场路耦合法对系统中异步电机的瞬态性能进行分析。该电机为6 800 kW,750 r/min。针对其3种不同的工况,即空载起动、风机负载起动、大负载起动,分别进行分析计算,模拟系统中电机由电动机状态切换成发电机状态的过程,获得该三相异步电机在不同状态下的瞬时起动电流、电磁转矩、气隙磁密等电气参数,进而分析该异步电机的瞬态性能和相应的电磁场分布。     

Twistor-based synchronous sliding mode control of spacecraft attitude and position

A synchronous control of relative attitude and position is required in separated ultra-quiet spacecraft, such as drag-free, disturbance-free, and distributed spacecraft. Thus, a twistor-based synchronous sliding mode control is investigated in this paper to solve the control problem of relative attitude and position among separated spacecraft modules. The twistor-based control design and the stability proof are implemented using the Modified Rodrigues Parameter (MRP). To evaluate the effectiveness of the proposed control method, this paper presents a case study of separated spacecraft flying control considering the mass uncertainty and external disturbances. In addition, a simulation study of the Proportional-Derivative (PD) control is also presented for comparison. The results indicate that the twistor-based sliding mode controller can ensure global asymptotic stability. The states converge fast with ultra-precision and ultra-stability in both the attitude and position. Moreover, the proposed twistor-based sliding mode control system is robust to the mass uncertainty and external disturbances.     

Performance analysis and application on Ti-6Al-4V of micro-forging system

Micro-forging (MF) is a novel surface modification technology which is capable of smoothening and strengthening the workpiece surface simultaneously. Based on analysis of the mechanism and energy conversion of micro-forging process, an electromagnetically driven micro-forging system is developed. To further grasp the kinetic characteristic of the equipment, a simulation model is established and its accuracy is verified. With the help of simulation and experimental results, we propose an input voltage optimization method, which drives the micro-forging head moving in a uniform and stable way. In this study, the influence of MF on surface integrity of Ti-6Al-4V (TC4) is firstly reported. Experimental results show that MF treatment reduces surface roughness (R_a) and increases micro-hardness by 48% and 11.8% at most, respectively. Besides, a compressive stress layer with an amplitude of −1000 MPa and a depth of 0.8 mm is observed. This study analyzes the performance and reveals the potential of micro-forging technology, which lays a solid foundation for expanding its application in TC4 surface modification.     

镜像铣削加工奇异区域刀具路径优化

在大型薄壁件镜像铣削加工中,由奇异点引起的旋转轴运动不连续会影响加工质量,降低加工效率。针对此问题,分析了镜像铣削加工奇异点存在的原因,提出了一种奇异区域内的刀具路径优化方法。首先,针对镜像铣削系统的铣削头和支撑头分别建立了其旋转轴运动学变换模型,推导旋转轴微分运动关系,据此分析奇异点存在的原因及其对加工质量和效率的影响,定义了机床行程内的奇异区域范围。分析结果表明在镜像铣削系统行程范围内,仅铣削头存在奇异区域,而支撑头不存在奇异区域。然后,在镜像铣削加工刀路约束条件下,基于刀路光顺性指标建立了刀路优化模型。通过在加工曲面参数域内对跨越铣削头奇异区域的刀路进行调整,使得优化后的刀路更加光顺,以提高加工精度和表面质量,减少奇异区域附近的加工时间。最后,通过镜像铣削加工实验验证所提方法的有效性。