N5B飞机机身钢构架焊接架数字化设计与制造技术

详细阐述了在N5B飞机机身钢构架焊接架的设计与制造中运用数字化技术的先进性。     

航空发动机风扇转子叶片外物损伤I.鸟撞击试验研究(英文)

本文改进了叶片鸟撞击试验条件。对某型发动机风扇一级转子叶片进行了鸟撞击试验。通过对叶片的鸟撞击瞬态响应分析和撞击前后叶片叶型变化的分析,验证了风扇一级转子叶片的抗鸟撞击性能,为某型发动机风扇转子叶片的抗外物损伤设计提供了依据。     

金属薄板超声无损检测

介绍了金属薄板的缺陷类型，建立了超声喷水穿透C扫描系统和检测方法。检测试验结果表明：采用建立的系统和方法能够检测出厚度≤6mm金属薄板中的分层性缺陷。     

Foreign Object Damage to Fan Rotor Blades of Aeroengine Part Ⅱ： Numerical Simulation of Bird Impact

Bird impact is one of the most dangerous threats to flight safety. The consequences of bird impact can be severe and, therefore, the aircraft components have to be certified for a proven level of bird impact resistance before being put into service. The fan rotor blades of aeroengine are the components being easily impacted by birds. It is necessary to ensure that the fan rotor blades should have adequate resistance against the bird impact, to reduce the flying accidents caused by bird impacts. Using the contacting-impacting algorithm, the numerical simulation is carded out to simulate bird impact. A three-blade computational model is set up for the fan rotor blade having shrouds. The transient response curves of the points corresponding to measured points in experiments, displacements and equivalent stresses on the blades are obtained during the simulation. From the comparison of the transient response curves obtained from numerical simulation with that obtained from experiments, it can be found that the variations in measured points and the corresponding points of simulation are basically the same. The deforming process, the maximum displacements and the maximum equivalent stresses on blades are analyzed. The numerical simulation verifies and complements the experiment results.     

旋转机翼悬停气动特性研究

鸭式旋转机翼(CRW)是一种先进的高速直升机方案,旋翼同时也是机翼,是其最关键气动部件之一。采用结构分区拼接网格技术进行空间离散,分区建立参考系,通过求解多重参考系下的N-S方程来计算旋翼流场,首先以传统的Caradonna-Tung实验旋翼的亚、跨声速悬停流场分析为例验证该方法的可靠性,进而采用该方法对旋转机翼悬停流场进行了数值计算,旋翼拉力计算值和地面实验值吻合较好,结果分析表明旋转机翼的悬停流场有着不同于传统旋翼的流场特性。     

高焓激波风洞喷管流场非平衡特性研究

高焓激波风洞是开展高超声速流动研究的重要地面模拟设备,但其产生的高焓气流在喷管中的膨胀过程是一种典型的热化学非平衡流动,试验段特征参数通过直接实验测量难以完全确定。本文通过求解耦合双温度模型的轴对称Navier-Stokes方程,研究了高焓激波风洞中典型状态下气流的热化学非平衡流动特性,分析了焓值对非平衡特性的影响规律。结果表明,喷管出口自由流均匀区域达到出口截面直径的75%以上,能够为实验提供足够的空间;喷管出口自由流处于热化学非平衡状态,在喷管喉道后约1/5喷管长度处气流即已处于冻结流状态,组分浓度和振动温度随气流流动基本不变;焓值在8.4MJ/kg~19.5MJ/kg之间变化时,非平衡程度随着焓值的增加而增强,但是低焓值时非平衡程度的增强更加剧烈。     

Attitude control system design and on-orbit performance analysis of nano-satellite––‘‘Tian Tuo 1’’

‘‘Tian Tuo 1'(TT-1) nano-satellite is the first single-board nano-satellite that was successfully launched in China. The main objective of TT-1 is technology demonstration and scientific measurements. The satellite carries out the significant exploration of single-board architecture feasibility validation, and it is tailored to the low-cost philosophy by adopting numerous commercialoff-the-shelf(COTS) components. The satellite is featured with three-axis stabilization control capability. A pitch bias momentum wheel and three magnetic coils are adopted as control actuators.The sun sensors, magnetometers and a three-axis gyro are employed as the measurement sensors.The quaternion estimator(QUEST) and unscented Kalman filter(UKF) method are adopted for the nano-satellite attitude determination. On-orbit data received by ground station is conducted to analysis the performance of attitude determination and control system(ADCS). The results show that the design of ADCS for TT-1 is suitable, robust and feasible.     

基于响应面近似技术的平流层飞艇协同设计优化

针对平流层飞艇多学科设计优化问题,引入协同优化算法,分析基于响应面近似模型的协同优化方法CO/RSA的执行步骤和特点,并介绍响应面近似模型的构建方法;建立平流层飞艇各学科模型,并对学科间耦合关系进行分析;运用建立的气动/推进、结构、能源三个耦合子系统的学科分析模型和系统优化模型,以平流层飞艇总质量最小为优化目标,综合考虑浮重、推阻和能源平衡,采用CO/RSA方法对平流层飞艇进行设计优化.结果表明:所建立的平流层飞艇的MDO模型是合理的,CO/RSA算法应用于飞艇总体设计优化是有效的,研究结果可为平流层飞艇方案论证和方案设计提供参考.     

现代喷气战斗机的发动机安装设计

发动机安装设计是飞机设计的一项重要工作,战斗机的发动机安装设计工作尤为重要且任务复杂.本文在收集整理大量文献资料的基础上,概述现代战斗机发动机的安装设汁,重点剖析了国外八个型号战斗机的发动机安装设计实例,比较各型战机的发动机安装设计异同,包括安装形式设计和安装节等结构部件的细节设计等.通过实例剖析和异同比较,有助于深入理解发动机安装设计的特点和规律,发展我国有自身特色的发动机安装设计解决方案.     

重复固溶对Inconel 718合金组织性能的影响

以982℃固溶水冷状态的Inconel 718合金棒材为研究对象,分析该合金经重复固溶再时效处理后的组织性能,并与直接时效处理进行对比。结果表明:在941~1010℃范围内重复固溶,随着固溶温度的升高,晶粒无明显变化,但是δ相含量逐渐减少,主要强化相γ′′的析出量增多,使合金硬度、高温拉伸强度和高温持久寿命显著提高,高温拉伸塑性、高温持久塑性在982℃固溶时达到极大值。与直接进行时效处理相比,经982℃重复固溶再时效处理后的组织性能无明显变化,更低的重复固溶温度对性能不利,而更高的重复固溶温度则使性能提高。