舰载无人机拦阻着舰中机身冲击响应分析

针对某舰载无人机拦阻着舰过程中的机体强度问题,以其中机身结构为主要研究对象,首次设计了包括中机身结构与前后机身、机翼假件以及拦阻钩等构件的地面拦阻模拟试验方案,并搭建了相应装置,采用地面试验和刚柔耦合仿真模拟2种方法,对拦阻着舰过程中拦阻力冲击下中机身结构的动态响应特性进行了全面分析。试验与仿真结果表明：中机身最大航向过载沿两条主传力路径自后机身到前机身方向衰减,下传递路径点的过载峰值明显大于上传递路径点的峰值;发现最大过载点位于拦阻接头处,应变危险点位于机腹梁前段处;中机身结构上各测点的试验和仿真过载误差均在5%以内,应变误差均在8%以内,验证了试验结果的有效性和刚柔耦合数值仿真方法的可行性。地面拦阻试验及数值仿真的联合分析可为舰载无人机机身结构强度设计提供重要参考,并为后续舰载无人机的拦阻着舰分析以及机身结构响应预测提供依据。     

Experimental investigation on aero-heating of rudder shaft within laminar/turbulent hypersonic boundary layers

The aero-heating of the rudder shaft region of a hypersonic vehicle is very harsh, as the peak heat flux in this region can be even higher than that at the stagnation point. Therefore, studying the aero-heating of the rudder shaft is of great significance for designing the thermal protection system of the hypersonic vehicle. In the wind tunnel test of the aero-heating effect, we find that with the increase of the angle of attack of the lifting body model, the increasement of the heat flux of the rudder shaft is larger under laminar flow conditions than that under turbulent flow conditions. To understand this, we design a wind tunnel experiment to study the effect of laminar/turbulent hypersonic boundary layers on the heat flux of the rudder shaft under the same wind tunnel freestream conditions. The experiment is carried out in the ?2 m shock tunnel(FD-14 A) affiliated to the China Aerodynamics Research and Development Center(CARDC). The laminar boundary layer on the model is triggered to a turbulent one by using vortex generators, which are 2 mm-high diamonds. The aero-heating of the rudder shaft(with the rudder) and the protuberance(without the rudder) are studied in both hypersonic laminar and turbulent boundary layers under the same freestream condition. The nominal Mach numbers are 10 and 12, and the unit Reynolds numbers are2.4 × 10~6 m~(-1) and 2.1 × 10~6 m-1. The angle of attack of the model is 20°, and the deflection angle of the rudder and the protuberance is 10°. The heat flux on the model surface is measured by thin film heat flux sensors, and the heat flux distribution along the center line of the lifting body model suggests that forced transition is achieved in the upstream of the rudder. The test results of the rudder shaft and the protuberance show that the heat flux of the rudder shaft is lower in the turbulent flow than that in the laminar flow, but the heat flux of the protuberance is the other way around,i.e., lower in the laminar flow than in the turbulent flow. The wind tunnel test results is also validated by numerical simulations. Our analysis suggests that this phenomenon is due to the difference of boundary layer velocities caused by different thickness of boundary layer between laminar and turbulent flows, as well as the restricted flow within the rudder gap. When the turbulent boundary layer is more than three times thicker than that of the laminar boundary layer, the heat flux of the rudder shaft under the laminar flow condition is higher than that under the turbulent flow condition. Discovery of this phenomenon has great importance for guiding the design of the thermal protection system for the rudder shaft of hypersonic vehicles.     

Robust adaptive compensation control for unmanned autonomous helicopter with input saturation and actuator faults

This paper studies a robust adaptive compensation Fault Tolerant Control(FTC) for the medium-scale Unmanned Autonomous Helicopter(UAH) in the presence of external disturbances,actuator faults and input saturation.To improve the disturbance rejection capacity of the UAH system in actuator healthy case, an adaptive control method is adopted to cope with the external disturbances and a nominal controller is proposed to stabilize the system.Meanwhile, compensation control inputs are designed to reduce the negative effects derived from actuator faults and input saturation.Based on the backstepping control and inner-outer loop control technologies, a robust adaptive FTC scheme is developed to guarantee the tracking errors convergence.Under the presented FTC controller, the uniform ultimate boundedness of all closed-loop signals is ensured via Lyapunov stability analysis.Simulation results demonstrate the effectiveness of the proposed control algorithm.     

主流湍流度对涡轮导叶吸力面W型气膜孔冷却效率影响的实验研究

为了获得亚声速涡轮导叶吸力面不同位置处单排W型气膜孔的气膜冷却特性,在短周期跨声速风洞中实验研究了吹风比、主流湍流度对W型气膜孔冷却效率的影响。两列单排气膜孔分别布置在吸力面16%和21%相对弧长处,实验进口雷诺数范围为3.0×10⁵~9.0×10⁵,吹风比范围是0.5~2.0,叶栅出口等熵马赫数为0.8,高低湍流度分别为14.7% 和1.3%。实验结果表明：低湍流度时孔排1和孔排2下游的气膜冷却效率都随吹风比的增大先增大后减小,最佳吹风比分别为BR=1.2和BR=0.8。由于孔排1和孔排2所处位置的主流边界层状态不同,导致湍流度对于气膜冷却效率有不同的影响。对于孔排1,大吹风比时高湍流度使冷气核心向壁面移动,提高了气膜冷却效率;而小吹风比时,湍流度对冷却效率的影响随雷诺数升高而减弱。对于孔排2,大吹风比时高湍流度提高了孔附近区域的冷却效率,同时加快了冷却效率沿流向下降的速度,而在小吹风比时高湍流度显著降低了孔排下游气膜冷却效率。     

封严篦齿特征参数对其密封性能影响的数值分析

利用软件CFX对直通型篦齿的内部流动进行模拟,研究了直通型篦齿齿距、转速对其泄漏量的影响.计算结果表明:篦齿泄漏量随齿距的增大而减少,篦齿转速对篦齿泄漏量的影响很小.另外,本文提出一种变齿距直通型篦齿,研究变齿距对篦齿泄漏量的影响,并对变齿距齿形所处位置对泄漏量的影响进行研究.     

冶金法提纯多晶硅退火工艺优化的数学模型分析与试验验证

冶金法制备多晶硅过程中,通过对不同退火温控方案进行数学建模,探求优化的退火理论温度控制函数与曲线。数学模型表明,对硅铸锭直接进行保温,依靠自然热平衡退火,会使内部应力大于产生位错的临界应力;采用加热元件对硅铸锭适当加热保温可减缓降温速率。通过比较,选择较低的退火温度1 236℃和较短的退火时间8.52 ks作为试验退火温控方案。试验验证表明,该退火方案得到的多晶硅铸锭目视裂纹较少,少数载流子寿命与电阻率具有明显优势。     

某平台卫星发射及在轨力学环境测量与分析

为获取航天器准确的发射及在轨力学环境数据,设计了一套具有数据采集、存储和传输功能的星载测量系统。利用该系统对某大型平台卫星发射飞行过程进行了测量,获取了星箭界面及卫星结构典型位置在发射主动段的正弦振动响应、随机振动响应、冲击响应及在轨微振动的环境数据。将测量数据与星箭载荷耦合分析结果、地面力学试验结果进行了详细对比,结果表明:星箭载荷耦合分析的结果在星箭界面处横向相对准确,而纵向在有限频段准确,其他频段及星上分析结果均大于测量结果,即存在极大裕度;地面试验结果大于测量结果,意味着有较大的裁剪设计空间。测量数据对后续卫星模型修正、试验条件设计、相似平台卫星抗力学环境优化、部组件设计等均具有重要的参考价值。     

激光驱动典型几何形状碎片运动建模研究

在以往的激光烧蚀驱动移除空间碎片研究中,均假设激光光束覆盖整个所关注的空间碎片。文章提出了焦斑式激光辐照下球体、圆柱体和立方体碎片反喷冲量和运动姿态的计算模型,研究了激光辐照在3种形状碎片不同位置处所产生的反喷冲量和姿态变化规律。结果表明:碎片运动规律与碎片几何形状和激光作用位置有关,当反喷冲量过质心时,碎片获得平动冲量;不过质心时,则会改变碎片的角速度或姿态。研究结果可为激光移除空间碎片研究提供理论参考。     

基于ABAQUS的复合材料网格筒分层破坏分析

复合材料网格筒结构由于极优的高比强度及比刚度特性,在运载火箭、飞机、卫星等航空航天结构中得到广泛应用。采用ABAQUS对复合材料网格筒结构进行精细化建模,详细分析了复合材料网格筒中的应力分布、分层破坏形式,研究了网格分层破坏出现的位置及对其整体刚度的影响。对网格筒桁条交界处的应力进行详细分析,研究了工艺缺陷对其破坏模式的影响。根据整体分析结果及局部分析结果,设计了承载能力为3500kN,质量为30kg的复合材料网格筒结构。研究成果将为复合材料结构网格筒的分析及设计提供参考。     

多旋翼无人机飞行控制自动调参技术

目前,多旋翼无人机控制器设计问题中存在着大量的依靠经验的调参工作。为了使调参简单而又可靠,本文基于控制器参数与控制系统性能响应存在的对应关系,提出了自动调参思想。在满足控制器各项性能指标的前提下,利用粒子群算法(Particle swarm optimization,PSO)提炼出优化目标和约束条件。对被控对象进行建模并搭建非线性模型。然后,利用工程实践方法估算出参数范围,并利用粒子群快速优化特点自动寻找在约束条件下符合性能指标的控制器参数。最后,通过Matlab/Simulink对模型进行仿真验证。仿真结果分析表明,PSD可快速准确地对飞行控制进行自动调参。