Hypervelocity impact induced shock acoustic emission waves for quantitative damage evaluation using in situ miniaturized piezoelectric sensor network

Manmade debris and natural meteoroids, travelling in the Low Earth Orbit at a speed of several kilometers per second, pose a severe safety concern to the spacecraft in service through the HyperVelocity Impact(HVI). To address this issue, an investigation of shock Acoustic Emission(AE) waves induced by HVI to a downscaled two-layer Whipple shielding structure is performed,to realize a quantitative damage evaluation. Firstly a hybrid numerical model integrating smoothparticle hydrodynamics and finite element is built to obtain the wave response. The projectiles, with various impact velocities and directions, are modelled to impact the shielding structure with different thicknesses. Then experimental validation is carried out with built-in miniaturized piezoelectric sensors to in situ sense the HVI-induced AE waves. A quantitative agreement is obtained between numerical and experimental results, demonstrating the correctness of the hybrid model and facilitating the explanation of obtained AE signals in experiment. Based on the understanding of HVI-induced wave components, assessment of the damage severity, i.e., whether the outer shielding layer is perforated or not, is performed using the energy ratio between the regions of ‘‘high frequency" and ‘‘low frequency" in the acquired AE signals. Lastly, the direct-arrival fundamentalsymmetric wave mode is isolated from each sensing signal to be input into an enhanced delay-andsum algorithm, which visualizes HVI spots accurately and instantaneously with different sensor network configuration. All these works demonstrate the potential of quantitative, in situ, and real time HVI monitoring using miniaturized piezoelectric sensor network.     

纵向波纹隔热屏气膜冷却特性实验

针对加力燃烧室纵向波纹隔热屏气膜冷却效果开展了细致的实验研究,利用红外热像仪测量了隔热屏壁面的温度分布,分析了隔热屏板型、吹风比、开孔率等参数对气膜冷却效率的影响。实验中板型选取了平板和纵向波纹隔热屏,吹风比变化范围是0.5~3.0,开孔率变化范围是1.4%~3.7%。结果表明:相比于平板隔热屏的气膜冷却效率沿程逐渐增加,纵向波纹隔热屏的气膜冷却效率随波纹板的起伏而起伏且大于平板隔热屏;随着吹风比的增加气膜冷却效率逐渐加大,在吹风比为3.0时达到最大值;气膜冷却效率在波峰处低,波谷处高,整体上随波纹板的起伏而波动,吹风比越小,气膜冷却效率随波纹板的起伏变化越明显;高吹风比(吹风比为2.0~3.0)下,气膜冷却效率沿程变化与增幅较为缓慢;整体上,随着开孔率的增加气膜冷却效率逐渐加大,小开孔率(开孔率为1.4%、2.7%)下的气膜冷却效率相差不大,但在次流背风侧,开孔率小的气膜冷却效率要小于开孔率大的气膜冷却效率。      

Behavior and functional modeling methods of doubly salient electromagnetic generators for aircraft electrical power system applications

The Doubly Salient Electromagnetic Generator(DSEG) is a promising candidate in aircraft generator application due to the simplicity, robustness and reliability. However, the field windings and the armature windings are strongly coupled, which makes the inductance characteristics non-linear and too complex to model. The complex model with low precision also leads to difficulties in modeling and analysis of the entire aircraft Electrical Power System(EPS). A behavior level modeling method based on modified inductance Support Vector Machine(SVM) is proposed. The Finite Element Analysis(FEA) inductance data are modified based on the experiment results to improve the precision. A functional level modeling method based on input–output characteristics SVM is also proposed. The two modeling methods are applied to a 9 kW DSEG prototype. The steady state and transient process precision of the proposed methods are proved by comparing with the experiment results. Meanwhile, the modeling time consumption, the application time consumption and the calculation resource demand are compared. The DSEG behavior and functional modeling methods provide precious results with high efficiency, which accelerates theoretical analysis and expands the application foreground of the DSEG in the aircraft EPS.     

应用于超级电容储能系统的双向DC/DC变换器混沌控制方法研究

超级电容储能系统(SCESS)主要通过对双向DC/DC变换器进行控制来快速平抑直流母线电压的波动。为了抑制控制过程中所产生的一些分岔和混沌现象,提出了一种应用于SCESS的混沌控制方法。分析了该方法的控制原理,并根据非线性动力学理论建立了双向DC/DC变换器的离散迭代模型;然后设计了一种能够自动调节补偿斜率的混沌控制信号;最后对该信号作用下的异步切换函数和同步切换映射式进行了数值求解,从而绘出系统分叉图。通过仿真和试验证明,该方法能够有效抑制SCESS的分岔和混沌现象,提高了系统的稳定工作范围和动态响应速度。     

Six sigma robust design optimization for thermal protection system of hypersonic vehicles based on successive response surface method

Lightweight design is important for the Thermal Protection System(TPS) of hypersonic vehicles in that it protects the inner structure from severe heating environment. However, due to the existence of uncertainties in material properties and geometry, it is imperative to incorporate uncertainty analysis into the design optimization to obtain reliable results. In this paper, a six sigma robust design optimization based on Successive Response Surface Method(SRSM) is established for the TPS to improve the reliability and robustness with considering the uncertainties. The uncertain parameters related to material properties and thicknesses of insulation layers are considered and characterized by random variables following normal distributions. By employing SRSM, the values of objective function and constraints are approximated by the response surfaces to reduce computational cost. The optimization is an iterative process with response surfaces updating to find the true optimal solution. The optimization of the nose cone of hypersonic vehicle cabin is provided as an example to illustrate the feasibility and effectiveness of the proposed method.     

超燃冲压发动机燃烧模态转换直连式实验研究

为获得燃烧模态转换过程对超燃冲压发动机工作特性的影响,在直连式实验台上,通过液态煤油流量的线性变化,开展了飞行马赫数4.5条件下燃烧室不同工作模态的转换实验。通过对特征位置和参数的监测,实现了燃烧模态的实时判别,获得了燃烧模态转换过程对发动机性能的影响规律。实验结果表明,在燃烧模态转换过程中滞环现象明显,燃烧室压力和发动机推力性能存在突变。在燃油流量以相同的速率增加和减小过程中发生模态转换时刻的燃油当量比存在差异,分别为0.55和0.488,两个转换点燃烧室比推相差8.05%。在滞环区间内,对于同一当量比,会存在两个不同燃烧模态,对应不同的发动机推力性能。     

高速进气道出口快速撤锥再起动特性研究

为了探寻出口快速撤锥过程对高速进气道起动性能的影响,对二元高速进气道出口快速撤锥过程开展了非定常数值仿真研究。对比了进气道在一个喘振周期中从不同状态点处进行快速撤锥所表现出的起动性能的差异。研究表明,当来流马赫数低于进气道的加速自起动马赫数时,对于高速进气道因出口堵锥节流所引起的不起动流态(喘振),从不同喘振状态开始撤锥,进气道表现出不同的起动特性,而进气道最终能否顺利建立起动流态与快速撤锥时机的选取有关。     

真实气体效应对Ma10级进气道流动的影响

为了探究高马赫数超燃冲压发动机高速飞行时真实气体效应对进气道流场的影响,仿真获得了不同气体模型下Ma10级进气道流场结构和性能。结果表明:进气道主流流场温度较低,不足以触发空气的离解反应,反应仅发生在边界层内,但反应程度较低,远未达到化学平衡状态,除了边界层温度及热载荷特性,其流场结果则更为贴近冻结流流场,因而化学非平衡模型与热完全气体模型的进气道通流流场结构和性能基本一致。而真实气体效应导致边界层特性的不同,对进气道起动特性产生影响,吸热离解反应通过对进口分离包的抑制和增大进口马赫数将进气道的再起动马赫数从9.8降低到9.4。在对进气道在宽速域应用中的钝化设计研究发现,真实气体效应虽然对前缘钝化进气道流场的压力分布和性能无明显影响,但是其能起到整体降低壁面热流的作用,不仅钝头处的热流降低了1MW/m2,通道内的热流也整体降低了0.1MW/m2。     

等离子体助燃下超燃支板燃烧室燃烧特性数值研究

为了将支板喷注器与等离子体射流这两种促进超声速燃烧室燃烧的方式结合起来,设计了一种带有等离子体射流喷孔的支板燃烧室,并在超声速来流的条件下,针对燃料喷注总压、燃料喷注位置、等离子体射流介质、等离子体射流总压对燃烧室燃烧性能的影响进行了三维数值模拟。研究发现:增大燃料的喷注总压,燃烧室的燃烧范围明显增大,燃烧效率呈现出先增大后减小的趋势,在燃料喷注总压为2.0MPa时,燃烧效率达到最大值90.4%;不同的燃料喷注位置对燃烧室的燃烧范围影响较小;等离子体射流介质为O2时,燃烧效率最高,燃烧范围最广;提高等离子体射流的喷注总压,能够提升凹腔剪切层高度,有效促进燃烧,但同时也带来了更高的总压损失。     

导流锥结构参数对燃气弹射筒内压力冲击平滑效果影响研究

针对导流锥结构参数对内弹道流场耦合影响问题,基于动态分层动网格技术,构建了含导弹运动和二次燃烧的内弹道数值模型,并验证了模型可靠性。解耦分析了导流锥半径、高度及冲击高度对内弹道流场特性和载荷的影响。结果表明：导流锥的结构直接决定燃气飞溅现象的产生和流场结构的紊乱程度,导流锥的半径、高度和冲击高度的改变会对燃气反射点的位置、二次燃烧的区域以及剧烈程度产生影响;结构优化后的导流锥,较大程度地缓解了冲击现象,获得了较好的平滑效果,筒底压力较实验装置降低了24.5%。