褶皱对碳纤维复合材料层合板压缩性能的影响

为研究纤维褶皱对碳纤维复合材料层合板压缩性能的影响,参考ASTM D6641—2014完成了含纤维褶皱碳纤维层合板压缩性能试验;同时采用基于Hashin失效准则及性能逐渐退化的渐进损伤方法进行了有限元分析。结果表明：褶皱程度为30%的凹陷试验件压缩极限载荷相比完好试验件降低了58.48%;同等褶皱程度下凹陷试验件比凸起试验件抗压强度更低;褶皱程度为30%的凹陷试验件刚度相比完好试验件降低了35.80%;有限元分析结果与试验吻合良好,试验件的损伤最初为基体损伤,经过扩展导致试验件在褶皱处断裂。     

高超声速钝锥模型及其尾迹红外辐射实验研究

介绍了利用InSb红外辐射计在弹道靶上测量底部直径为10mm、半锥角和头部半径分别为9°、2.2mm(模型A),8°、0.6mm(模型B)的两种非烧蚀钝锥模型及其尾迹的红外辐射.模型速度大于6km/s,飞行环境压力约4.8kPa,红外辐射测量波段为1~3μm、3~5μm.结果表明:非烧蚀钝锥模型头身部红外辐射远大于尾迹红外辐射,在相同飞行速度和环境压力条件下,模型A产生的红外辐射比模型B产生的红外辐射强.     

钛合金胶接点焊接头的性能检测

研究了不同焊接电流下钛合金板胶接点焊接头的A扫描信号和C扫描图像特征,并进行了拉伸-剪切试验。结果表明:通过观察C扫描图像的特征与A扫描信号的变化,能够划分胶接点焊接头的胶层区、热影响区、熔合区、熔核区以及焊接缺陷;随着电流(7~10 k A)的逐渐增大,接头熔核直径呈递增趋势,相应的失效载荷从7 231.5增加到10 939.0 N;当电流为7 k A时,在C扫描图像上反映出飞溅缺陷,此时接头失效载荷远小于没有出现飞溅的接头,可见飞溅降低了胶接点焊接头的拉剪载荷。     

一种利用ILSP的同步DS-CDMA信号快速盲解扩算法

针对同步DS-CDMA信号的盲解扩问题，本文提出了一种基于迭代最小二乘投影算法(ILSP)的快速盲解扩算法。本算法首先通过对截获信号的协方差矩阵进行特征分解，估计出由各用户扩频序列张成的信号子空间，然后结合扩频码序列的有限符号集特性，利用ILSP算法消除由特征分解产生的酉矩阵模糊问题，得到扩频序列的精确估计，最后利用估计得到的扩频序列对截获信号解扩得到信息码序列，完成DS-CDMA信号的盲解扩。仿真结果表明本算法在低信噪比条件下具有良好的盲解扩性能，且相较传统算法本文提出算法大大降低了计算复杂度 。     

Crystal orientation and morphology of a lamellae in wrought titanium alloys: On the role of microstructure evolution in b processing

To obtain high-quality aviation forgings of titanium alloys, b forging is an essential processing step which must be considered throughout a production process. In this work, the effect of b forging on the crystal orientation and morphology of lamellar a was experimentally investigated in a two-phase titanium alloy. Strong dynamic recovery during b working resulted in the formation of low-angle grain boundary(LAGBb) inside b grains. The lamellar a can penetrate through the LAGBb, leading to similar intra a LAGBs on subgrain boundaries. Deformation banding occurs at high strain rates, and both diffusive and sharp boundaries of deformation bands can be observed.A continuous change of the b orientation in diffusive boundaries results in the formation of fine and disordered a lamellae without intra-lamellar boundary to hold the Burgers orientation relationship(OR). On sharp boundaries, it is prone to producing continuous grain boundary a(aGB) with a highly similar orientation along the boundaries. Meanwhile, there may exist several lower-angle boundaries within the grain boundary a for a smoother orientation change on the b grain boundary.     

A new dynamic pushback control method for reducing fuel-burn costs: Using predicted taxi-out time

Long departure-taxi-out time leads to significant airport surface congestion, fuel-burn costs, and excessive emissions of greenhouse gases. To reduce these undesirable effects, a Predicted taxi-out time-based Dynamic Pushback Control(PDPC) method is proposed. The implementation of this method requires two steps: first, the taxi-out times for aircraft are predicted by the leastsquares support-vector regression approach of which the parameters are optimized by an introduced improved Firefly algorithm. Then, a dynamic pushback control model equipped with a linear gate-hold penalty function is built, along with a proposed iterative taxiway queue-threshold optimization algorithm for solving the model. A case study with data obtained from Beijing International airport(PEK) is presented. The taxi-out time prediction model achieves predictive accuracy within 3 min and 5 min by 84.71% and 95.66%, respectively. The results of the proposed pushback method show that total operation cost and fuel-burn cost achieve a 14.0% and 21.1%reduction, respectively, as compared to the traditional K-control policy.(3) From the perspective of implementation, using PDPC policy can significantly reduce the queue length in taxiway and taxi-out time. The total operation cost and fuel-burn cost can be curtailed by 37.2% and 52.1%,respectively, as compared to the non-enforcement of any pushback control mechanism. These results show that the proposed pushback control model can reduce fuel-burn costs and airport surface congestion effectively.     

技术注释标准化管理研究

主要对技术注释标注的标准化、规范化进行探讨,提出利用数据库技术对技术注释进行标准化管理,并给出了实际可行的建库思路,指导了技术注释数据库系统的整个建设过程.     

液化天然气作为航空燃料的发展趋势及特点分析

为研究液化天然气(LNG)作为航空燃料的可行性,对LNG的特点、发展趋势及作为航空燃料存在的问题进行了分析.采用了横向比较的方法,将LNG与新的航空替代燃料和传统航空燃料进行了比较和计算分析.结果表明:与新的航空替代燃料相比,LNG具有来源广泛、经济性好、发动机适应性强等优点.与传统航空燃料相比,LNG的储量大,可使用100年以上;可燃极限宽、污染物排放低,NOx排放仅为航空煤油的1/4;单位质量能量密度高、成本低,其燃料成本仅为航空汽油的一半,航空煤油的1/3;同时还具有可用于发动机高温部件冷却用的冷能,是一种极富潜力的航空燃料.指出在LNG作为航空燃料方面急需开展动力系统与飞机结构的匹配、燃料相态的有效转化及不同燃料在燃烧室内的反应特性等方面的研究工作.      

基于人工地标的移动机器人定位与调整技术

在飞机大型构件测量领域,针对测量设备自动化转站时存在移动机器人无法准确到达站位的问题,提出了采用基于人工地标的移动机器人定位与调整技术实现转站时的精确定位。其次,设计了一种人工地标,给出使用激光跟踪仪的地标标定工装以及标定方法,通过该方法可得到地标在全局坐标系下的坐标。同时,介绍了地标的编码与位姿的解算方法,以及移动机器人位姿调整策略。最后,试验表明,人工地标测量的位置和角度误差均较小,移动机器人通过人工地标的定位与调整后的精度可以满足自动化转站的精度要求。