The OSIRIS-REx Thermal Emission Spectrometer (OTES) Instrument

The OSIRIS-REx Thermal Emission Spectrometer (OTES) will provide remote measurements of mineralogy and thermophysical properties of Bennu to map its surface, help select the OSIRIS-REx sampling site, and investigate the Yarkovsky effect. OTES is a Fourier Transform spectrometer covering the spectral range 5.71–100 μm (\(1750\mbox{--}100~\mbox{cm}^{-1}\)) with a spectral sample interval of \(8.66~\mbox{cm}^{-1}\) and a 6.5-mrad field of view. The OTES telescope is a 15.2-cm diameter Cassegrain telescope that feeds a flat-plate Michelson moving mirror mounted on a linear voice-coil motor assembly. A single uncooled deuterated l-alanine doped triglycine sulfate (DLATGS) pyroelectric detector is used to sample the interferogram every two seconds. Redundant ～0.855 μm laser diodes are used in a metrology interferometer to provide precise moving mirror control and IR sampling at 772 Hz. The beamsplitter is a 38-mm diameter, 1-mm thick chemical vapor deposited diamond with an antireflection microstructure to minimize surface reflection. An internal calibration cone blackbody target provides radiometric calibration. The radiometric precision in a single spectrum is \(\leq2.2 \times 10^{-8}~\mbox{W}\,\mbox{cm}^{-2}\,\mbox{sr} ^{-1}/\mbox{cm}^{-1}\) between 300 and \(1350~\mbox{cm}^{-1}\). The absolute integrated radiance error is \(<1\%\) for scene temperatures ranging from 150 to 380 K. The overall OTES envelope size is \(37.5 \times 28.9 \times 52.2~\mbox{cm}\), and the mass is 6.27 kg. The power consumption is 10.8 W average. OTES was developed by Arizona State University with Moog Broad Reach developing the electronics. OTES was integrated, tested, and radiometrically calibrated on the Arizona State University campus in Tempe, AZ.     

A linear stability analysis of large-Prandtl-number thermocapillary liquid bridges

A linear stability analysis is applied to determine the onset of oscillatory thermocapillary convection in cylindrical liquid bridges of large Prandtl numbers (4  Pr  50). We focus on the relationships between the critical Reynolds number Re_c, the azimuthal wave number m, the aspect ratio Γ and the Prandtl number Pr. A detailed Re_c–Pr stability diagram is given for liquid bridges with various Γ. In the region of Pr > 1, which has been less studied previously and where Re_c has been usually believed to decrease with the increase of Pr, we found Re_c exhibits an early increase for liquid bridges with Γ around one. From the computed surface temperature gradient, it is concluded that the boundary layers developed at both solid ends of liquid bridges strengthen the stability of basic axisymmetric thermocapillary convection at large Prandtl number, and that the stability property of the basic flow is determined by the “effective” part of liquid bridge.     

A detailed FLUKA-2005 Monte-Carlo simulation for the ATIC detector

We have performed a detailed Monte-Carlo (MC) simulation for the Advanced Thin Ionization Calorimeter (ATIC) detector using the MC code FLUKA-2005 which is capable of simulating particles up to 10 PeV. The ATIC detector has completed two successful balloon flights from McMurdo, Antarctica lasting a total of more than 35 days. ATIC is designed as a multiple, long duration balloon flight, investigation of the cosmic ray spectra from below 50 GeV to near 100 TeV total energy; using a fully active Bismuth Germanate (BGO) calorimeter. It is equipped with a large mosaic of silicon detector pixels capable of charge identification, and, for particle tracking, three projective layers of x–y scintillator hodoscopes, located above, in the middle and below a 0.75 nuclear interaction length graphite target. Our simulations are part of an analysis package of both nuclear (A) and energy dependences for different nuclei interacting in the ATIC detector. The MC simulates the response of different components of the detector such as the Si-matrix, the scintillator hodoscopes and the BGO calorimeter to various nuclei. We present comparisons of the FLUKA-2005 MC calculations with GEANT calculations and with the ATIC CERN data.     

Gamma-ray detector on board lunar mission Chang’E-1

Gamma-ray spectrometer (GRS) is included in the payload of Chinese first lunar mission Chang’E-1 that will be launched in 2007. Specific objectives of the GRS are to map abundance of O, Si, Fe, Ti, U, Th, K, and perhaps, Mg, Al, and Ca to depths of about 20 cm. There are remarkable advantages for GRS application to remote sensing elemental materials over the entire lunar surface: large effective area and good ability for background rejection. We will describe the design of GRS and present its performance in this paper. Moreover, the GRS calibration will also be introduced.     

Temperature effects in the ATIC BGO calorimeter

The Advanced Thin Ionization Calorimeter (ATIC) Balloon Experiment had a successful test flight and a science flight in 2000–01 and 2002–03 and an unsuccessful launch in 2005–06 from McMurdo, Antarctica, returning 16 and 19 days of flight data. ATIC is designed to measure the spectra of cosmic rays (protons to iron). The instrument is composed of a Silicon matrix detector followed by a carbon target interleaved with scintillator tracking layers and a segmented BGO calorimeter composed of 320 individual crystals totaling 18 radiation lengths to determine the particle energy. BGO (Bismuth Germanate) is an inorganic scintillation crystal and its light output depends not only on the energy deposited by particles but also on the temperature of the crystal. The temperature of balloon instruments during flight is not constant due to sun angle variations as well as differences in albedo from the ground. The change in output for a given energy deposit in the crystals in response to temperature variations was determined.     

Comments, with reply, on `Status of CR-like lower bounds fornonlinear filtering' by T.H. Kerr

The commenters object to criticisms of their work that appeared in the above-titled paper (ibid., vol.25, no.5, p.590-601, Sept. 1989) and provide a defense of their results. The author presents further arguments to buttress his claims     

A fusion and learning algorithm for landing aircraft tracking:compensating for exhaust plume disturbance

An algorithm is presented for tracking a landing aircraft using fusion of two different passive sensors, a laser range finder (LRF) and a forward-looking infrared (FLIR) camera. The main feature of this algorithm is its ability to identify and compensate for an exhaust plume disturbance. The algorithm is based on the extended Kalman filter (EKF) and the filtering confidence function (FCF) which introduces a learning approach to the tracking problem. The results of a simulation using the learning tracking algorithm and the EKF alone are presented and compared     

Dust hazard near Halley Comet in case of the VEGA project

The motion of dust particles near Halley Comet is studied and the probability of dust impacts with the spacecraft in case of the VEGA (Venus-Halley)- project is determined. The formation of a crater due to a particle impact with the dust shield is considered and the necessity for using a dual-sheet bumper shield is substantiated. The thickness of a front sheet that plays a role of the particle evaporator is estimated theoretically. The numerical experiment is carried out that simulates the dynamics of collision and evaporation of a particle. Three factors causing perforations of the rear sheet are discussed, i.e. dust penetrated through holes in the front sheet, gas jets and spall fragments of the front-sheet. The consideration of these factors makes it possible to estimate basic parameters of the dual-sheet bumper shield. Flexural vibrations of the front sheet under action of the reverse gaseous jet from the rear sheet are discussed that can affect essentially the shield strength. The perturbing effect of the dust and gas fluxes on the spacecraft is studied.     

New progress on space solar telescope

The design of the Space Solar Telescope (phase B) has been completed. The telescope system has been manufactured (phase C) since the beginning of 1999, and it will be assembled by the end of 2000. In this paper, mainly the optical design, technique and manufacture will be described. The launch is planned for the summer of 2004.