民用飞机燃油箱系统闪电防护分析方法研究

民机燃油箱系统的闪电防护是燃油箱安全的重要研究范畴,本文依据FAA的25-146号修正案和咨询通告AC25.954-1,介绍了民用飞机燃油箱系统闪电防护分析方法。在点火源防护分析思路的基础上,针对闪电引起的点火源,在明确飞机闪电分区后,可通过容错类设计或非容错类设计分别开展分析。针对容错类设计,可仅通过证明防护设计特征有效且可靠来表明符合性,无需进一步分析失效概率。针对非容错类设计,通过定性和定量分析法进行评估。在定性分析时,需评估非容错特征失效且引起点火源的概率小于1E-5。在定量分析中,可结合燃油箱可燃性、关键闪电和防护特征失效概率确保闪电引起燃油蒸气点燃的概率为极不可能。同时,根据闪电环境定义的电流振幅和波形对防护设计特征进行有效性验证。     

碳纤维热导率与其微观结构参数的关系

碳纤维具有多晶多相特性,为了研究微晶结构特性对热导率的影响,本文通过XRD对碳纤维的微观特征结构参数的表征,对导热性能与微观特征结构的关联性进行了研究。研究结果表明,碳纤维热导率随着石墨微晶的基面宽度（L_a）、堆砌厚度（L_c）和平均堆垛层数（N）的增大而增大,随着孔隙率（V_p）的增大而降低。基于Raman图谱的分峰拟合信息,对碳纤维的石墨化度进行分析。结果显示,碳纤维的石墨化度越大,热导率越高。     

多芯片组件（MCM）用金锡焊带材料电阻率及热导率温度特性研究

对牌号为Au₈₀Sn₂₀的金锡焊带材料在208~423 K的电阻率及热导率与温度的函数关系进行了研究,并对其在多芯片组件（MCM）中的传热效果进行了评估。分别对材料在208~423 K中5个温度点的电阻率及4个温度点的热导率进行了测试,基于理论模型建立电阻率/热导率随温度变化的函数关系,最终采用模拟热扩散数值方法评估材料在高温下的传热能力。结果表明,采用修正函数模型后,金锡焊带材料在208~423 K下热导率与电阻率的关系符合测试结果,随芯片表面温度的边界条件从208 K升高至423 K,采用变温热导率模型得到的热流密度模拟计算结果相比理想化恒定热导率模型的差异性逐渐升高至5.5%。综上,金锡焊带材料热导率与电阻率的关系符合Wiedemann-Franz法则修正后的Smith-Palmer方程,在该材料传热设计时应考虑其热导率温度效应。     

可编程约瑟夫森电压标准低温探杆的设计

由于约瑟夫森电压标准的关键器件——约瑟夫森结需要工作在4.2 K的低温环境中[1],而标准使用的其它仪器则工作在室温环境中,因此需要设计一种沟通低温环境和室温环境的测试探杆,即可以将偏置电流和75 GHz微波传送到约瑟夫森结上,又可以将约瑟夫森结产生的量子电压输出到校准所需的仪器上。本文对可编程约瑟夫森电压标准的低温探杆的绝热设计、精密电测设计和微波传输设计做了介绍。     

GRACE gravity field modeling with an investigation on correlation between nuisance parameters and gravity field coefficients

The GRACE (Gravity Recovery And Climate Experiment) monthly gravity models have been independently produced and published by several research institutions, such as Center for Space Research (CSR), GeoForschungsZentrum (GFZ), Jet Propulsion Laboratory (JPL), Centre National d’Etudes Spatiales (CNES) and Delft Institute of Earth Observation and Space Systems (DEOS). According to their processing standards, above institutions use the traditional variational approach except that the DEOS exploits the acceleration approach. The background force models employed are rather similar. The produced gravity field models generally agree with one another in the spatial pattern. However, there are some discrepancies in the gravity signal amplitude between solutions produced by different institutions. In particular, 10%–30% signal amplitude differences in some river basins can be observed. In this paper, we implemented a variant of the traditional variational approach and computed two sets of monthly gravity field solutions using the data from January 2005 to December 2006. The input data are K-band range-rates (KBRR) and kinematic orbits of GRACE satellites. The main difference in the production of our two types of models is how to deal with nuisance parameters. This type of parameters is necessary to absorb low-frequency errors in the data, which are mainly the aliasing and instrument errors. One way is to remove the nuisance parameters before estimating the geopotential coefficients, called NPARB approach in the paper. The other way is to estimate the nuisance parameters and geopotential coefficients simultaneously, called NPESS approach. These two types of solutions mainly differ in geopotential coefficients from degree 2 to 5. This can be explained by the fact that the nuisance parameters and the gravity field coefficients are highly correlated, particularly at low degrees. We compare these solutions with the official and published ones by means of spectral analysis. It is found that our solutions are, in general, consistent with others in the spatial pattern. The water storage variations of the Amazon, Chari and Ganges river basins have also been computed. The variations computed with the NPARB approach are closer to those produced by JPL and DEOS solutions, while the variations produced with the NPESS approach are in good agreement with those produced by the CSR and GFZ solutions. A simulation study is implemented with considering realistic noise and low-frequency error. The two approaches are used to recover the true model. The NPESS solution appears closer to the true one. Therefore we are inclined to estimate the nuisance parameters simultaneously with the geopential coefficients.     

Conceptual design of a bioregenerative life support system containing crops and silkworms

This article summarizes a conceptual design of a bioregenerative life support system for permanent lunar base or planetary exploration. The system consists of seven compartments – higher plants cultivation, animal rearing, human habitation, water recovery, waste treatment, atmosphere management, and storages. Fifteen kinds of crops, such as wheat, rice, soybean, lettuce, and mulberry, were selected as main life support contributors to provide the crew with air, water, and vegetable food. Silkworms fed by crop leaves were designated to produce partial animal nutrition for the crew. Various physical-chemical and biological methods were combined to reclaim wastewater and solid waste. Condensate collected from atmosphere was recycled into potable water through granular activated carbon adsorption, iodine sterilization, and trace element supplementation. All grey water was also purified though multifiltration and ultraviolet sterilization. Plant residue, human excrement, silkworm feces, etc. were decomposed into inorganic substances which were finally absorbed by higher plants. Some meat, ingredients, as well as nitrogen fertilizer were prestored and resupplied periodically. Meanwhile, the same amount and chemical composition of organic waste was dumped to maintain the steady state of the system. A nutritional balanced diet was developed by means of the linear programming method. It could provide 2721 kcal of energy, 375.5 g of carbohydrate, 99.47 g of protein, and 91.19 g of fat per capita per day. Silkworm powder covered 12.54% of total animal protein intakes. The balance of material flows between compartments was described by the system of stoichiometric equations. Basic life support requirements for crews including oxygen, food, potable and hygiene water summed up to 29.68 kg per capita per day. The coefficient of system material closure reached 99.40%.     

可靠性设计优化的球空间设计法

可靠性设计优化（RBDO）在航空航天等领域已经被广泛应用,具有显著提高可靠性的效果;然而它包含两个迭代循环-总体优化循环和可靠性分析循环,双循环求解方法效率低下甚至难以承受。本文提出一种可以提高可靠性设计优化求解效率的方法-球空间设计法,该方法可以方便地表达搜索区域,最大可能失效点可以从极值点处精确获取;同时,该方法可以将总体优化以及可靠性分析同步进行。本文所提出的球空间法的有效性将通过2个算例进行测试,测试结果表明该方法不仅精度与同类方法持平,求解效率有明显提升,它将会对提高航空航天装备如卫星、火箭、飞行器等产品的可靠性提供更为有效的方法和技术支持。