矩形截面管道气流中横向运动颗粒的碰壁条件

分析了矩形截面管道气流中横向运动颗粒的运动轨迹及碰壁条件,研究表明颗粒飞出的临界速度随着颗粒直径的增大而减小,当颗粒直径较小时受来流密度、马赫数影响较大,总趋势是来流密度、马赫数越大,颗粒越不容易与上壁面碰撞。但随着颗粒直径的增大,来流条件对颗粒是否碰壁的影响逐渐减弱,决定因素是颗粒直径的大小和颗粒的喷射速度。     

Experimental research on rotating detonation with liquid hypergolic propellants

This paper describes experimental research into the initiation and propagation of rotating detonation for liquid Nitrogen TetrOxide (NTO) and liquid MonoMethylHydrazine (MMH). An annular rocket-type combustor without nozzle was designed to investigate detonation combustion. The propellants were injected through unlike impingement injectors. The combustion flame fronts and pressure waves were detected using optical diagnostics and dynamic pressure sensors, respectively. The propagation of rotating detonation was established spontaneously by increasing the mass flow rate of propellants. The velocity of propagation of the flame fronts and pressure waves was nearly equal and reaches supersonic speed. Two different detonation combustion patterns are present, single wave mode and double waves mode. And in double waves mode, the two detonation waves are always counter-rotating. The possibility of rotating detonation initiation in a combustor with nozzle was also checked. Stable rotating detonation can be initialized and sustained at similar operating conditions.     

基于卷积门控循环网络的滚动轴承故障诊断

针对许多基于深度学习的滚动轴承故障诊断方法在小样本数据集下诊断性能下降的问题,提出一种基于卷积门控循环神经网络的轴承故障诊断模型。该模型使用两层的卷积网络来从输入信号中提取特征,同时使用tanh函数作为激活函数,且池化层使用大池化核来进行重叠下采样。将所提取得到的高层特征连接到双向门控循环网络。合并循环网络正向和逆向的最后一个状态,并连接一层全连接层进行输出。选用凯斯西储大学的轴承故障数据集来验证模型在小样本数据集下的诊断性能,实验结果表明,相比于其他类型的模型,该模型在仅有20个训练样本的情况下依然保持97%的识别准确率。      

民用飞机复合材料舱门优化设计

复合材料因其具有比刚度大、比强度高、可设计性强等特点而被广泛应用到民用飞机结构上。针对宽体复合材料舱门设计方案,建立有限元模型进行初步分析,然后以刚度设计要求和强度设计要求为约束条件,对复合材料舱门结构的铺层比例进行了优化,达到了复合材料舱门的减重目的。优化后复合材料舱门的重量降低了10%以上,并且满足所有刚度和强度设计要求。本文所做研究为复合材料气密舱门减重提供了一种有效的方法,并且为类似结构的设计提出了参考建议,在工程上具有一定的指导意义。     

基于STM32F429的全向运动平台的运动控制

全向运动平台系统是可以实现人体在各个方位行走的2D运动平台。针对实现人体在全向运动平台稳定行走的运动控制,采用加入观测器的一阶控制算法对平台运动控制进行探究。先通过MATLAB软件进行算法的仿真,验证方法的可行性;再通过现场测试,验证控制算法的有效性。最终试验表明,加入观测器的一阶控制算法可对全向运动平台实现有效的运动控制。此运动控制策略的探究为全向运动平台的运动控制提供了一种可行的控制思路和方案。     

Numerical investigation of flow mechanisms of tandem impeller inside a centrifugal compressor

This study numerically investigated a single stage centrifugal compressor ‘‘Radiver’’ with a wedge diffuser and several tandem-designed impellers to explore the flow phenomena within the tandem impeller and the potential to enhance compressor performance. The results demonstrate that tandem design and clocking fraction (λ_s) significantly affects the compressor performance. The compressor stage with tandem impellers of Series A of boundary layer growth interruption alone are observed to have a widely operating range but efficiency and total pressure ratio penalty compared with that of conventional impeller. The tandem impeller with at least the same impeller efficiency as the conventional design is considered as a critical design criteria so that further modification process based on the flow characteristic of tandem impeller is necessary. In order to restrain the inducer wake and exducer shock losses, parameters modification of blade angle and thickness distributions are necessary and the modified tandem impeller of Series B is obtained. The modified tandem impeller with 25% clocking arrangement shows an 8.45% stall margin increase and maintains the total pressure ratio and efficiency as the conventional design, which proves the potential of tandem impeller to improve compressor stage performance. It is noteworthy that the tandem impellers of Radiver have not shown obviously balanced exit flow field and the fundamental mechanism of stall margin extending of tandem impeller lies on the improved impeller/diffuser matching performance resulting from the incidence angle variation at diffuser inlet.     

Real-time object tracking via least squares transformation in spatial and Fourier domains for unmanned aerial vehicles

This paper addresses the problem of real-time object tracking for unmanned aerial vehicles. We consider the task of object tracking as a classification problem. Training a good classifier always needs a huge number of samples, which is always time-consuming and not suitable for realtime applications. In this paper, we transform the large-scale least-squares problem in the spatial domain to a series of small-scale least-squares problems with constraints in the Fourier domain using the correlation filter technique. Then, this problem is efficiently solved by two stages. In the first stage, a fast method based on recursive least squares is used to solve the correlation filter problem without constraints in the Fourier domain. In the second stage, a weight matrix is constructed to prune the solution attained in the first stage to approach the constraints in the spatial domain. Then, the pruned classifier is used for tracking. To evaluate proposed tracker's performance, comprehensive experiments are conducted on challenging aerial sequences in the UAV123 dataset. Experimental results demonstrate that proposed approach achieves a state-ofthe-art tracking performance in aerial sequences and operates at a mean speed of beyond 40 frames/s. For further analysis of proposed tracker's robustness, extensive experiments are also performed on recent benchmarks OTB50, OTB100, and VOT2016.     

惯导系统旋转机构轴承动力学建模方法研究

旋转机构是旋转调制捷联惯导系统的关键部件之一。为了精确模拟旋转机构的动力学特性,研究了支撑旋转轴系的双列球轴承的动力学建模方法,提出了使用Bushing单元来建立同时具有径向移动刚度、轴向移动刚度和径向角刚度的三向刚度轴承动力学模型的方法。利用有限元数值仿真方法计算了三向刚度数值,并利用轴承手册上的经验公式进行了验证。在此基础上,建立了含弹性轴承支撑的旋转调制捷联惯导系统旋转机构的结构动力学有限元模型,分析比较了轴承有无角刚度两种状态下的固有模态。分析结果表明:对于旋转调制捷联惯导系统旋转机构来说,轴承模型角刚度对计算精度的影响较大,角刚度已知的模型更接近真实情况。     

基于参数化分析的柔性后缘优化设计

介绍了一种自适应柔性机翼后缘变形控制优化设计方法,该方法采用了由单个驱动器驱动的单块式分布柔性结构。该方法的关键在于设计一种合适的柔性后缘结构拓扑形式,使该自适应柔性机翼后缘能够达到精确的变形。阐明了柔性结构拓扑优化设计的数学模型,针对自适应柔性机翼后缘概念设计提出了基于参数化分析的拓扑优化设计方案,并进行了工程化圆整和尺寸优化。最终,通过非线性有限元分析和功能测试,验证了本文提出的柔性后缘优化设计方法的合理性。     

Nutation instability of spinning solid rocket motor spacecraft

The variation of mass,and moment of inertia of a spin-stabilized spacecraft leads to concern about the nutation instability.Here a careful analysis on the nutation instability is performed on a spacecraft propelled by solid rocket booster (SRB).The influences of specific solid propellant designs on transversal angular velocity are discussed.The results show that the typical SRB of End Burn suppresses the non-principal axial angular velocity.On the contrary,the frequently used SRB of Radial Burn could amplify the transversal angular velocity.The nutation instability caused by a design of Radial Burn could be remedied by the addition of End Burn at the same time based on the study of the combination design of both End Burn and Radial Burn.The analysis of the results proposes the design conception of how to control the nutation motion.The method is suitable to resolve the nutation instability of solid rocket motor with complex propellant patterns.