基于CFAR检测的SAR噪声干扰效果评估方法

在研究美国林肯实验室的SAR恒虚警(CFAR)自动目标检测方法的基础上,分析了CFAR目标检测技术在不同噪声干扰强度下检测概率的变化情况,并结合图像相关性分析得出一种改进的基于CFAR检测技术的SAR噪声干扰效果评估方法.     

电大目标等离子体隐身的矩量法优化设计

根据高频散射特征,提出典型几何散射中心替代法,用于解决矩量法（MOM）用于电大目标等离子体隐身时的优化设计问题。以某典型电大目标为例,通过仿真分析了该方法的可行性。结果显示,电大目标覆盖利用该方法得到最优参数的等离子体后,不仅目标整体的单站RCS平均缩减与典型几何散射体的单站RCS缩减相当,且任意方向上RCS基本都有10dB左右的缩减,表明用该方法得到用于电大目标隐身的等离子体参数是可行的。     

大直径铝合金铆钉以铆代螺可行性试验研究

针对双层铝合金板铆接结构,通过电磁铆接工艺试验,分析Φ10mm-2A10铝合金铆钉镦头的微观组织,与钢质螺栓连接接头对比评价了铆接接头的力学性能。研究发现,随放电电压的增加,铆钉镦头直径逐渐增加、高度逐渐降低。铆钉镦头以绝热剪切为主要变形模式。铆接接头的最大剪切和拉脱载荷分别为23.3k N和35.0k N,均高于钢质螺栓连接接头,并且相对于螺接接头可减重15.8%。     

磁轴承控制器的设计及仿真研究

介绍了磁轴承系统的组成,对控制器性能的基本要求及控制方案的选择,分析了典型ＰＩＤ控制器存在的两个弊端,提出了磁轴承控制器的四种模型。通过对这四种模型的仿真研究,分析了各模型中比例系数、积分时间常数、微分时间常数及局部反馈系数对系统性能的影响,并给出了各参数较为理想的参考值及阶跃响应曲线,仿真结果对制作模拟控制器及数字控制器有一定的借鉴作用。     

卫星通信干扰样式研究

综述通信对抗干扰的分类方式,分析了部分文献中对干扰样式划分的不合理性.根据卫星通信对抗的特点将通信对抗干扰样式进行分类,并从与压制式干扰相区别的角度对欺骗式干扰做出研究分析.     

高速BPSK相干光通信系统对激光器线宽要求

文章概述了激光器相位噪声对零差相干检测光通信系统性能的影响，对特定的基于平衡探测的科斯塔斯（Costas）环路接收系统相位误差进行了详细的理论分析，最后获得了不同传输码速率下的零差相干检测光通信系统对激光器线宽的具体要求。     

Measurements of heat transfer and pressure in a trailing edge cavity of a turbine blade

 An experimental investigation is conducted to obtain the heat transfer and pressure drop data for an integral trailing edge cavity test section that simulates a novel turbine blade's internal cooling passage with bleed holes. Local heat transfer is measured on both the suction and pressure sides by a transient liquid crystal technique, while pressures at six positions are recorded by pressure calibrators. Moreover, flow characteristic and its effect on heat transfer are analyzed for conditions with or without bleed flow. The experimental results show that, in the cases with bleed flow, local heat transfer on the pressure side exceeds that on the suction side in the first and second channels. In the cases without bleed flow, in the first and third channels, local heat transfer on the suction side weakens whilst it increases significantly on the pressure side. For the second channel, non-bleed condition leads to a more balanced heat transfer distribution between the upstream and downstream channel. Besides, after the bleed holes are blocked, heat transfer in the first bend region on the suction side declines sharply, while the opposite phenomenon occurs for the second bend region on the pressure side. In both bleed and non-bleed cases, the total pressure of six measurement positions decreases continuously along the channel at the same Reynolds number and it promotes for higher Reynolds number. Among all the measurement points, under the same flow rate condition, the highest speed occurs at Position 5, which also shows the maximum difference between the total and static pressures. When the bleed holes are blocked, the total pressure at each measurement position appears to increase.     

关于进行程序管制一体化模拟练习的设想

在程序管制模拟练习中，存在着塔台管制服务、进近管制服务和区域管制服务互不衔接，不能系统地模拟整个管制过程的问题。针对这一情况提出了程序管制一体化模拟练习和程序和管制一体化模拟机的结构设计。     

Characteristics of low-latitude whistlers and their relation with f0F2 and magnetic activity

Some results obtained from the characteristics of low-latitude whistlers received at Wuchang (Geomag. Lat. 19.2°N), Zhanjiang (9.8°N) and Yulin (6.4°N) are presented. The observations cover three years at Wuchang, two years at Zhanjiang, one year at Yulin.     

光学基片表面软质抛光胶体粒子的激光清洗

介绍了光学基片表面软质抛光胶体粒子激光清洗的基本方法、原理和实验装置,并通过对含有污染微粒的基片表面进行激光清洗,获得了高洁净表面的光学基片.