带轴对称台阶的圆锥高超声速边界层转捩试验

在Ma 6风洞内,通过高频脉动压力测试技术和基于纳米粒子示踪的平面激光散射(NPLS)技术,分别对带前向、后向轴对称台阶的圆锥高超声速边界层转捩进行了试验研究。采用功率谱密度分析和互相关计算等方法对脉动压力数据进行分析,得到了边界层中扰动波的发展规律,定量分析了第二模态波的相关参数。结果显示：两种模型中第二模态波在沿流向向下游发展的过程中,其幅值均先增大再衰减、特征频率均逐渐减小;特征频率和传播速度整体上均随雷诺数的增大而增加(后台阶模型中特征频率由100 kHz增至196 kHz,前台阶中则由 97 kHz 增至174 kHz)、波长变化规律则与之相反(后台阶中由6.35 mm降至4.54 mm,前台阶由7.35 mm降至 4.66 mm );后台阶模型中第二模态波初次出现位置比前台阶中更靠近上游,边界层转捩位置较前台阶前移。将NPLS结果与高频脉动压力测试结果进行对比,两者吻合较好。     

战术导弹中小型固体发动机技术的发展

通过对战术导弹中小型固体发动机具体发展需求的分析,明确了高能化、轻质化、可控化和低易损4个主要的中小型固体发动机发展方向。可以从提高推进剂黏合剂密度和燃烧室工作压强来实现高能化;采用轻质高性能金属壳体、纤维缠绕复合材料壳体以及提高绝热层性能以实现轻质化;可控化需要在高功率密度的驱动装置、高精度的控制算法等方面获得突破和支撑;低易损则可以从钝感推进剂、主动扩稳、防护材料等途径开展工作。通过对这4个技术方向上国内外研究现状和发展趋势进行梳理,明确提出未来研究需要突破推进剂和热防护原材料、新型装药工艺、可调燃气阀门、压力闭环控制和有效扩稳等关键技术,加速工程化进程,为我国战术导弹的跨越式发展提供支撑。     

Experiment on Boiling Heat Transfer of Refrigerant R134a in Mini-channels

The flow boiling heat transfer characteristics of refrigerant R134 a flowing inside two different kinds of minichannels are investigated. One channel is multi-port extruded with the hydraulic diameter of 0.63 mm,and the other one is rectangular with offset fins and a hydraulic diameter of 1.28 mm. The experiments are performed with a mass flow rate between 68 and 630 kg/(m~2·s),a heat flux between 9 and 64 kW/m~2,and a saturation pressure between 0.24 and 0.63 MPa,under the constant heat flux heating mode. It is found that the effect of mass flow rate on boiling heat transfer is related to heat flux,and that with the increase of heat flux,the effect can only be efficient in higher vapor quality region. The effects of heat flux and saturation pressure on boiling heat transfer are related to a threshold vapor quality,and the value will gradually decrease with the increase of heat flux or saturation pressure. Based on these analyses,a new correlation is proposed to predict the boiling heat transfer coefficient of refrigerant R134 a in the mini-channels under the experimental conditions.     

Rotation Control of a 3-DOF Parallel Mechanism Driven by Pneumatic Muscle Actuators

The pneumatic muscle actuator(PMA) has many advantages,such as good flexibility,high power/weight ratio,but its nonlinearity makes it difficult to build a static mathematical model with high precision. A new method is proposed to establish the model of PMA. The concept of hybrid elastic modulus which is related to the static characteristic of PMA is put forward,and the energy conservation law is used to achieve the expression of the hybrid elastic modulus,which can be fitted out based on experimental data,and the model of PMA can be derived from this expression. At the same time,a 3-DOF parallel mechanism(a new bionic shoulder joint)driven by five PMAs is designed. This bionic shoulder joint adopts the structure of two antagonistic PMAs actualizing a rotation control and three PMAs controlling another two rotations to get better rotation characteristics. The kinematic and dynamic characteristics of the mechanism are analyzed and a new static model of PMA is used to control it.Experimental results demonstrate the effectiveness of this new static model.     

自动铺丝最小间隙路径规划与复合材料锥壳结构制造

自动铺丝技术（AFP）是提高复合材料构件制造效率和降低其制造成本的关键技术和重要手段。铺放轨迹的设计是控制自动铺丝工艺质量的关键。对于复杂的结构形式,合理的铺丝路径对保证可制造性及铺贴质量至关重要。本文针对简化后的后机身锥壳特征结构,研究了基于固定角法、测地线法和变角度法的自动铺丝轨迹算法设计,解决了铺放复杂曲面满覆盖问题;总结对比获得了不同铺丝轨迹方法的特点和适用范围。以保证工艺性并满足结构设计铺层方向为原则,选用了带宽为6.35 mm的自动铺丝预浸料完成工艺验证件制造,并通过有限元分析评估了自动铺丝轨迹算法的合理性。结果表明：该结构宜采用测地线法铺放0°方向铺层以减少褶皱;采用固定角法铺放90°方向铺层能够保证连续铺放;采用结合预浸窄带侧弯试验结果的变角度轨迹规划方法铺放此锥类构件±45°方向铺层能够保持最小间隙。铺丝间隙使锥壳结构单层等效模量下降约30%,整体强度下降约10%。因而在结构优化设计时需考虑自动铺丝工艺对安全裕度影响的因素。     

某航天器输氢管道系统结构完整性评估

为保障某航天器在服役年限内不发生事故,针对航天器上采用插入焊接技术的精密管道系统进行结构完整性评估。在考虑到系统存在整圈的环形未焊透缺陷基础上,结合工程实践,假设在焊接区域存在更危险的平面缺陷。首先,开展高压气相热充氢试验下的标准拉伸和三点弯试验得到管道系统材料"J-75"在临氢环境下应力应变曲线和断裂韧性。其次,采用有限元程序计算系统在内压、惯性载荷与离面位移作用下的应力分布,考虑到间隙配合中的不确定性,改变模型中的最大间隙多次模拟计算,发现最大应力位置基本不变,以此区域作为假想缺陷的具体萌生区域。最后,采用失效评估图（FAD）方法对存在4种缺陷模式的系统分别进行结构完整性评估。通过引入安全裕度的概念,发现系统在含有初始尺寸（0.15 mm）的4种平面缺陷时,均处于安全状态,并且安全裕度都在2倍以上;通过工程临界分析（ECA）发现随着缺陷尺寸的增大,系统中含有缺陷2（位于管道焊接区域最大应力处的轴对称平面且沿焊深方向扩展的缺陷）时最为危险,且当缺陷深度超过0.61 mm时将断裂失效;考虑到测试数据的弥散性,针对系统最危险的模式,以安全裕度为可靠性指标,将失效评估图方法与可靠性评价相结合,得到系统在含有尺寸为0.15 mm的缺陷2情况下保有足够安全裕度的可靠性下限值超过0.999 5。     

弹用“X”,型倒置二元进气道方案与常规正置方案的气动性能对比

为提高来流马赫数范围为2~4的“X”型进气系统大攻角下的稳定裕度,设计并研究了一种倒置二元进气道设计方案,并将其与正置方案进行了比较。结果表明:来流马赫数为2.3~3.5,攻角范围为0°~6°时,倒置布局设计方案总体性能较优,未出现明显激波/附面层干扰问题,能够满足设计要求。在采用相同的进气道设计方案时,倒置布局其迎风与背风进气道结尾激波位置及总体性能参数差异更小;0°攻角时倒置布局临界总压恢复系数与正置布局相当,4°攻角时倒置布局比正置布局高2%~3%,8°攻角时普遍高19%以上,且来流马赫数越高提升幅度越明显,8°攻角下倒置布局总流量系数较正置布局高6%左右。研究还发现,当来流马赫数较低时倒置布局总阻力低于正置布局, 4°攻角时低1.7%;而来流马赫数较高时倒置布局总阻力高于正置布局,4°攻角时高2.0%。      

基于改进粒子群优化模糊控制的MPPT算法研究

在光照强度和温度变化时,常规的最大功率点跟踪(MPPT)算法难以快速准确地跟踪光伏系统最大功率点。针对此问题,设计了一种改进粒子群优化算法(PSO)的模糊控制器。首先,依据常规MPPT特性,设计了一种带调整因子的模糊控制算法以快速收敛到最大功率点;然后,采用参数自适应PSO对设计的模糊控制器调整因子进行动态优化。仿真结果表明:所设计的参数自适应PSO优化模糊控制器能快速准确地跟踪最大功率点,保证了MPPT的动态响应速度和稳态精度,提高了光伏系统的工作效率。     

基于定子电阻自适应辨识的感应电机死区补偿

电压源型逆变器由于死区效应,导致输出发生非标准化、畸变化,影响感应电机的控制精确度,特别是无速度传感器矢量控制,同时造成电网侧能量的流失。为了减小死区效应产生的影响,列出误差计算公式,求得总延时时间。另外,对定子电阻进行自适应辨识,增加所求延时时间精确度的同时可以运用到电机矢量控制中。经过补偿误差电压,提高了控制性能,降低了对控制系统的影响。结果表明所提补偿策略对电流波形、总谐波失真具有改善作用。     

Behavior and functional modeling methods of doubly salient electromagnetic generators for aircraft electrical power system applications

The Doubly Salient Electromagnetic Generator(DSEG) is a promising candidate in aircraft generator application due to the simplicity, robustness and reliability. However, the field windings and the armature windings are strongly coupled, which makes the inductance characteristics non-linear and too complex to model. The complex model with low precision also leads to difficulties in modeling and analysis of the entire aircraft Electrical Power System(EPS). A behavior level modeling method based on modified inductance Support Vector Machine(SVM) is proposed. The Finite Element Analysis(FEA) inductance data are modified based on the experiment results to improve the precision. A functional level modeling method based on input–output characteristics SVM is also proposed. The two modeling methods are applied to a 9 kW DSEG prototype. The steady state and transient process precision of the proposed methods are proved by comparing with the experiment results. Meanwhile, the modeling time consumption, the application time consumption and the calculation resource demand are compared. The DSEG behavior and functional modeling methods provide precious results with high efficiency, which accelerates theoretical analysis and expands the application foreground of the DSEG in the aircraft EPS.