空气中微细电火花沉积铜合金工艺方法

提出了一种在空气中将工具电极丝黄铜材料沉积到工件上的新工艺方法。实现该方法的基本条件为:(1)工具电极接脉冲电源正极;(2)在空气中放电;(3)窄脉宽配合宽脉间。通过大量实验对微细电火花沉积加工的工艺规律进行了系统深入的研究,得出各主要工艺参数对沉积工艺效果的影响规律。最终以黄铜电极丝为工具电极,在高速钢工件表面上沉积出直径为0.19 mm、高度为7.35 mm的微小圆柱体。利用SEM、能谱分析和X射线衍射及显微硬度测试等方法对沉积物进行分析,得出该沉积物的组织结构、化学成分和硬度等方面的基本性质,为进一步研究三维沉积加工奠定了基础。     

典型电离层多普勒记录及其讨论

由于地面电离层多普勒频率偏移测量具有时间连续、设备相对简便等固有特征，它特别适合于扰监测。本文在整理北京大学电离层高频多普勒台站观测资料的基础上，给出了一些典型电离层多普勒效应观测现象，这些现象反映了多普勒的细致分析对电离层形态学研究有其特殊意义。利用IRI模型，对多普勒频移的太阳耀斑效应及电离层不规则结构对多普勒频移的影响进行了模拟计算，理论结果与观测基本一致，从而大体上解释了这些响应的物理机制。论文最后对观测到的一种特殊的记录类型－－S型描迹的具体成因作了详细的分析和讨论，指出在一定条件下，以一定相位速度水平传播的声重波可以产生这类记录，给出了相位速度和振幅等声重波参数与记录描迹形状的关系，这对从多普勒频移记录推演电离层中的波动特征有一定的帮助。     

MONITORING OF ENERGETIC PARTICLE ENVIRONMENT INSIDE THE CHINA-BRAZIL EARTH RESOURCE SATELLITE

On 14 October 1999, the Chinese-Brazil earth resource satellite (CBERS-1) was launched in China. On board of the satellite there was an instrument designed at Peking University to detect the energetic particle radiation inside the satellite so the radiation fluxes of energetic particles in the cabin can be monitored continuously. Inside a satellite cabin, radiation environment consists of ether penetrated energetic particles or secondary radiation from satellite materials due to the interactions with primary cosmic rays.Purpose of the detectors are twofold, to monitor the particle radiation in the cabin and also to study the space radiation environment The data can be used to study the radiation environment and their effects on the electronics inside the satelhte cabin. On the other hand, the data are useful in study of geo-space energetic particle events such as solar proton events, particle precipitation and variations of the radiation belt since there should be some correlation between the radiation situation inside and outside the satellite.The instrument consists of two semi-conductor detectors for protons and electrons respectively. Each detector has two channels of energy ranges. They are 0.5-2MeV and ≥2MeV for electrons and 5-30MeV and 30-60MeV for protons. Counting rate for all channels are up to 104/(cm2@s)and power consumption is about 2.5 W. There are also the additional functions of CMOS TID (total integrated dose) effect and direct SEU monitoring. The data of CBMC was first sent back on Oct. 17 1999 and it's almost three years from then on. The detector has been working normally and the quality of data is good.The preliminary results of data analysis of CBMC not only reveal the effects of polar particle precipitation and radiation belt on radiation environment inside a satellite, but also show some important features of the geo-space energetic particle radiation.As one of the most important parameters of space weather, the energetic charged particles have great influences on space activities and ground tech nology. CBMC is perhaps the first long-term on-board special equipment to monitor the energetic particle radiation environment inside the satellite and the data it accnmulated are very useful in both satellite designing and space research.     

利用MF雷达对耀斑期间电离层D区电子密度的观测研究

利用MF雷达观测资料对X级别耀斑爆发期间在66-80km高度之间的电子密度进行了研究，观测到了耀斑爆发期间电子密度的突然增加，在较低高度上的电子密度的时间变化趋势与耀斑的软X射线辐射通量相关．电子密度的变化强度依赖于具体的耀斑参数，有些耀斑引起的电子密度增加高达400cm^-3，有些仅为100cm^-3左右．但耀斑期间在这一高度区间增加的总电子含量增量仅占耀斑辐射引起的整个电离层总电子含量增量的千分之一左右．最后，利用恢复阶段电子密度的时间变化过程估算了1997年11月4日耀斑期间部分高度上的有效复合系数．     

钛合金胶接点焊接头的性能检测

研究了不同焊接电流下钛合金板胶接点焊接头的A扫描信号和C扫描图像特征,并进行了拉伸-剪切试验。结果表明:通过观察C扫描图像的特征与A扫描信号的变化,能够划分胶接点焊接头的胶层区、热影响区、熔合区、熔核区以及焊接缺陷;随着电流(7~10 k A)的逐渐增大,接头熔核直径呈递增趋势,相应的失效载荷从7 231.5增加到10 939.0 N;当电流为7 k A时,在C扫描图像上反映出飞溅缺陷,此时接头失效载荷远小于没有出现飞溅的接头,可见飞溅降低了胶接点焊接头的拉剪载荷。     

新媒体视域下系统构建“三位一体”公寓管理模式

随着科技日益进步和5G时代的即将到来,在治理体系上越来越注重管理与哲学教育相结合,高校作为接收新事物、新思维的前沿阵地。学生公寓成为大学生思想政治教育的又一个重要的阵地,因此创新公寓管理体系并努力做到使之与哲学相结合也成为了一项重大任务,高校辅导员、公寓辅导员、高校后勤管理人员结合新媒体创新学生公寓的管理方式对新时代大学生的教育、管理、服务掌控和开展思想政治教育工作至关重要。     

A comprehensive study of the 2016 Mw 6.0 Italy earthquake based on high-rate (10 Hz) GPS data

The 2016 M_w 6.0 Italy earthquake is successfully recorded by the near-field 10?Hz GPS and 200?Hz Strong Motion (SM) stations, providing valuable data for this study. A comprehensive study of this earthquake is carried out based on GPS data, which contains coseismic deformations analysis, noise analysis, seismic wave picking, and magnitude determination. The noise of most GPS-derived displacement waveforms can be described as a combination of white noise, flicker noise, and random walk noise after the earthquake occurrence, and the spectral indices vary significantly for most stations, implying that the seismic signals have affected the noise characteristic of GPS-derived displacement waveforms. S-transform is employed to assess the GPS capability to detect the seismic arrival time. The SM station AMT and the GPS station AMAT are in good agreement in seismic wave picking, and the difference is only 1.2?s in the north component, suggesting that the outcome of seismic wave picking using GPS data is reliable. Then, a classic empirical formula is employed to determine the moment magnitude. A robust moment magnitude (Mw 5.90) can be estimated by the nine GPS stations with about 23.9?s. If four GPS stations near the epicenter is chosen to determine the magnitude, it only take 13.0?s to retrieve a reliable preliminary (Mw 5.82) magnitude, which is 5.4?s ahead of nine stations. In addition, Cross Wavelet Transform (XWT) is adopted to measuring the correlation and phase relationship between GPS and SM records. The result of XWT analysis indicates 10?Hz GPS is capable of capturing reliable and accurate coseismic dynamic deformations, as evidenced by the XWT-based semblance being close to 1 between GPS and SM records. The above results confirm the capability of 10?Hz GPS to capture coseismic dynamic deformations, detect seismic arrival time, and determine earthquake magnitude. Moreover, rapid magnitude determination based on 10?Hz GPS data can be regarded as an important supplement to Earthquake Early Warning (EEW).     

新一代战斗机非定常流动数值研究综述

新一代战斗机强调超机动能力和强隐身性，其中大攻角下的静态失速、动态失速及内埋弹仓绕流是与高机动和强隐身密切相关的、极具挑战的几类典型的非定常流动，它们对数值方法提出了极高的要求。为了高精度地仿真流场、清楚地揭示流动机理，有效地控制非定常流动，非常有必要发展高精度且高效率的RANS-LES混合方法体系，包含RANS-LES混合方法本身、与RANS-LES混合方法匹配的高精度自适应耗散格式、基准湍流模式、高质量计算网格、高精度时间推进方法、非定常量的统计方法等，具有极强的紧迫性。提出、发展、验证并应用该类方法数值仿真新一代战斗机（包括单独部件、组合体、甚至全机）的非定常流动，数值预测结果与风洞实验数据吻合良好；此类方法可为新型战斗机设计提供理论依据和分析手段。