A review of long drop tubes as a supplement/alternative to space experiments

The 100 meter high drop tube at the Marshall Space Flight Center has proven to be a viable facility for studies of containerless solidification. Advantages are that experiments are inexpensive and large numbers of specimens can be processed rapidly. It would not be unusual to run ten specimens in a day. Another significant advantage is that the undercooling behavior can be followed with sufficient sensitivity to easily detect the onset of recalescence and subsequent events.Disadvantages are the restrictions on specimen sizes and types of alloys that can be run in a microgravity environment. Practical specimen sizes range between 50 mg and 500 mg depending on the type of furnace being used. Refractory alloys can be processed in a vacuum (about 10^?5 torr) and therefore at microgravity. Non-refractory alloys demand an atmosphere (about 200 torr) to obtain appreciable undercooling before impact at the bottom of the tube. Under these conditions significant g forces result.Because of the present limitations of the 100 meter drop tube, the most definitive work has been done on niobium based alloys. Large amounts of undercooling have been observed routinely and the effects of undercooling on microstructure have been characterized in detail. X-ray diffraction, scanning electron microscopy, and transmission electron microscopy have been used to determine types of phases, amounts of phases, and compositions of phases. It is clear, as would be expected, that the results bear some resemblance to rapid solidification processing by quenching. However, there are dissimilarities due to the uniqueness of solidification by deep undercooling without quenching in long drop tubes and accompanying recalescence effects.     

IR-spectroscopy of ionosphere from stratospheric balloons

The radiation spectra of the ionosphere in the 4–5 μm region have been determined from stratospheric balloons by means of the specially elaborated method of the registration of angular and spectral distribution of the radiation. The radiation bands of 4.4 μm and 4.8 μm which have 0.1–0.2 erg cm^?2 sr^?1s^?1. brightness obtained in two flights, are identified with the vibration-rotation transitions of the ion NO⁺ (0 - 1) and the molecules N¹⁴N¹⁵ (0 - 1) and CO (0 - 1) and (3 - 2) from altitudes between 120 and 500 km.     

ELF radio signals produced in the auroral ionosphere by non-linear demodulation of signals from high-power amplitude-modulated transmitters

ELF and VLF radio signals were recorded in the afternoon to early morning (local time) between 24 March and 4 April 1979, in Northern Scandinavia. Apart from signals of natural origin, timing signals, i.e. six pips of equal duration of 105 ± 8 ms, at 1 kHz ± 0.5 Hz, were observed on the hour UT. Such signals only occur on days of relatively high geomagnetic activity during enhanced auroral electrojet activity. They are believed to be generated by non-linear demodulation (self-detection) of signals from two or more amplitude modulated transmitters in the USSR, operating at 173, 200, 236, 263 and 657 kHz. The simplest explanation for the observations is provided by the three transmitters operating at 173 kHz.     

Stimulation of plasma waves in the magnetosphere using satellite JIKIKEN (EXOS-B)

The stimulated plasma wave experiment (SPW) has been successfully carried out in the plasmasphere and the magnetosphere along the JIKIKEN (EXOS-B) satellite orbit where the plasma parameters indicate wide variety of the combination of the electron number density, ranging from 1/cc to 10⁴/cc, and the electron cyclotron frequency, ranging from 6 kHz to 200 kHz.The upper hybrid resonances F_UHR usually persists for long periods up to 125 msec and the electron cyclotron resonances nF_H are stimulated at frequencies with the very high harmonic number n; sometimes, the nF_H resonance takes place for n=47.All the features of the resonances including F_On reflect the characteristics of the magnetospheric plasma that contains the energetic and non-Maxwellian components of the particles. The measurement of the plasma resonance contributes to the detection of the local electron density and the magnetic field intensity. The mode of the propagating radio waves is also determined being compared with the observed local plasma resonance frequency F_p.     

Gravitational influence on binary alloy melt equilibria

Micro- and macrosegregation, the nonuniform redistribution of solute during solidification, are common to both casting and welding, processes of fundamental importance in materials engineering. In multicomponent crystal growth where solid/liquid density differences are appreciable gravity-induced separation can lead to significant spatial variations in resulting ingot composition. In fact, this phenomenon is also operative in liquid/liquid systems such as monotectic alloys exhibiting a liquid miscibility gap, where buoyancy-driven flows can result in a sometimes unwanted separation of phases upon cooling through the miscibility dome.     

Knowledge Acquisition for ATE Diagnosis

An applied intelligence program for ATE fault diagnosis shows promise as an effective method to reduce mean time to repair (MTTR). The types of knowledge required by an intelligent diagnostic for VLSI test systems, the resources needed to derive that knowledge, the approach implemented to organize it, and the final form of the knowledge representations which resulted from our work are discussed in this paper.     

Application of remote sensing techniques in mineral resources survey — a case study pertaining to Singhbhum Shear Zone,Bihar, India

Geological analysis and evaluation of digitally processed and enhanced LANDSAT MSS data products for three test areas of Singhbhum Shear Zone, India has led to certain significant results regarding optimisation and utility of such techniques for geological studies and obtaining additional/new information regarding lithology and structure. Three band-to-band ratio images are found to give best results. Lithologic formations could be subdivided into a number of units. The Westward and southeastward extension of the shear zone could be delineated thereby indicating scope of mineralisation in these parts.     

Ralicon anodes fabricated by electron beam lithography for image photon counting detectors

The Anger wedge and strip anode event location system developed for microchannel plate image photon detectors at the Space Sciences Laboratory of the University of California, Berkeley, has been extended in the present work by the use of electron beam lithography (EBL). Computer-aided design methods have been used to develop several types of RALICON ($\text{R}$eadout $\text{A}$nodes of $\text{Lit}$hographic $\text{Con}$struction) for use in photon counting microchannel plate imaging detectors. These anodes are suitable for linear, two dimensional or radial position measurements and they incorporate novel design features made possible by the EBL fabrication technique which significantly extend their application relative to published wedge-strip anode designs.     

Electromagnetic containerless undercooling facility and experiments for the shuttle

An electromagnetic furnace is being prepared for flights aboard the space shuttle. This apparatus is capable of melting metals and alloys up to 1400°C melting point by induction heating with subsequent solidification of the freely levitated melt without contact with any container. The solidification can be carried out with greatly reduced fields resulting in minimal heating and stirring of the free melt. Sequential specimens can be processed during flight. Several experiments are planned for a series of flights, beginning in 1985 with an undercooling experiment on NiSn alloys. These will be interspersed with detailed studies of fluid flow caused by low and high field levels in order to quantify the corresponding effect upon the solidification process.