Review of flow control mechanisms of leading-edge vortices

Vortex control concepts employed for slender and nonslender delta wings were reviewed. Important aspects of flow control include flow separation, vortex formation, flow reattachment, vortex breakdown, and vortex instabilities. The occurrence and relative importance of these phenomena strongly depend on the wing sweep angle. Various flow control methods were discussed: multiple vortices, control surfaces, blowing and suction, low-frequency and high-frequency excitation, feedback control, passive control with wing flexibility, and plasma actuators. For slender delta wings, control of vortex breakdown is achieved by modifications to swirl level and external pressure gradient acting on the vortex core. Effects of flow control methods on these two parameters were discussed, and their effectiveness was compared whenever possible. With the high-frequency excitation of the separated shear layer, reattachment and lift enhancement in the post-stall region is observed, which is orders of magnitude more effective than steady blowing. This effect is more pronounced for nonslender wings. Re-formation of vortices is possible with sufficient amplitude of forcing at the optimum frequency. Passive lift enhancement on flexible wings is due to the self-excited wing vibrations, which occur when the frequency of wing vibrations is close to the frequency of the shear layer instabilities, and promote flow reattachment.     

新型高残碳酚醛树脂的研究I.高残碳酚醛树脂的合成及其残碳率

合成了DA系列树脂改性剂和芳基改性酚醛树脂 ,并以DA改性剂改性芳基酚醛树脂。用热重、电子顺磁共振等方法研究了改性酚醛树脂的残碳率。研究表明 ,用DA改性剂来改性酚醛树脂是提高残碳率的有效方法 ,改性酚醛树脂的残碳率可达 6 9.87%。     

焊接残余应力盲孔测量精度的三维模拟

基于三维有限元分析方法,研究了应变释放系数与孔深、主应力和应变花方向夹角以及双轴比之间的关系.采用三维有限元方法对应变释放系数进行了修正,并通过修正系数对焊接残余应力进行了修正,修正后的残余应力分布更趋于合理.     

Digital Aircraft Sheet Metal Part Manufacturing System and Its Key Technology

The architecture of digital sheet metal manufacturing system is proposed based on the classification of sheet metal manufacturing information.The essence of digital manufacturing is the definition,management and transfer of information,and the key technologies are brought forward and described.It is pointed out that knowledge-based manufacturing elements design is necessary to make digital technology efficient.The management of all kinds of sheet metal manufacturing element information is to build single source of manufacturing data.Multi-state model-based digital transfer and coordination method is designed to provide a foundation for digital manufacturing of aircraft sheet metal part.The application of digital sheet metal manufacturing is exemplified with an aircraft sheet metal part.The application result is compared to that of the traditional analog transfer technology.It is shown that the developed technology can improve part quality,shorten manufacturing time and lower manufacturing cost.     

Phased array of large reflectors for deep-space communication

In this paper the problem of uplink array calibration for deep-space communication is considered. A phased array of many modest-size reflectors antennas is used to drastically improve the uplink effective isotropic radiated power of a ground station. A radar calibration procedure for the array phase distribution is presented using a number of in-orbit targets. Design of optimal orbit and the number of calibration targets is investigated for providing frequent calibration opportunities needed for compensating array elements phase center movements as the array tracks a spacecraft. Array far-field focusing based on the near-filed in-orbit (low Earth orbit (LEO)) calibration targets is also presented and array gain degradation analysis based on the position error of the array elements and in-orbit targets has been carried out. It is shown that errors in the in-orbit targets positions significantly degrade the far-field array gain while the errors in array elements positions are not very important. Analysis of phase errors caused by thermal noise, system instability, and atmospheric effects show insignificant array gain degradation by these factors     

污水处理装置在冶金行业中的应用

对污水处理装置的技术参数、技术要求及设计方案的选择、工作原理做了进一步的阐述。对工业循环冷却水的处理有实际指导意义。     

基于DCOM技术构建分布式数控故障诊断系统

简要介绍DCOM技术的特点,对利用DCOM技术构建分布式数控故障诊断系统进行了研究,并提出了系统的组件模型结构。     

新型精密狭缝的设计

介绍了一种基于弹性铰链的精密狭缝的设计，加工工艺要求和性能测试结果。根据实际需要，狭缝可以采用水冷结构。     

接触焊机理的探索

探讨了接触焊的机理，提出了以电位差选择电极材料的原则，以及焊接处的接触电阻和母材内阻在焊接中有一定作用，而且焊接处的总热能是各种能量产生的热量之和，焊接的总热量也应包括通电加热产生的热量和断电后（锻压时）产生的热量。     

一种改进的数字式波束形成的快速自适应算法

提出了一种改进的数字式波束形成的快速自适应算法,即具有严格约束最小功率的抽样矩阵梯度算法(CSMG)。它综合了传统抽样矩阵梯度、算法和具有严格约束的最小功率自适应算法的优点。计算机模拟表明,此算法波束方向随约束角度而变,自适应调零能力较强,收敛速度也较快。