MEMS陀螺零偏温度补偿模型研究

针对MEMS陀螺工作易受温度变化影响、角速度测量输出误差大、预热时间长的问题,通过大量实验数据分析、总结规律,建立了零偏温度补偿模型,并结合最小二乘法利用多元线性回归技术对模型参数进行了辨识。对比零偏温度补偿前后的试验结果表明,经过补偿后的MEMS陀螺不但测量精度得到提高,其工程应用稳定性也得到增强。     

TC21钛合金的微观组织对力学性能的影响

研究了两相钛合金TC21关于两种不同微观组织(片状组织和网篮组织)的拉伸性能、断裂韧性和疲劳裂纹扩展性能.结果显示:片状组织相比网篮组织有相近的拉伸强度,但塑性较差;两者的韧性相差不大,但增韧机理不同;网篮组织在中低速扩展区的扩展速率和片状组织几乎相同,但在较高速扩展区显示略低的扩展速率;加载方向对两种组织的疲劳裂纹扩展速率基本无影响;和其他钛合金类似,TC21在Paris区存在转折.     

涡流管结构参数对其性能的影响

用实验方法研究了热端管管长、分离室直径、冷孔板孔径等主要结构参数对涡流管的制冷制热性能的影响。实验中以空气为介质分别对不同结构参数涡流管的性能进行了研究,得出了热端管管长、分离室直径以及冷孔板孔径等参数对涡流管制冷制热性能的影响规律。研究结果表明:在一定范围内增加热端管长度有利于涡流管的能量分离;在大冷流率下,大直径涡流管的制冷性能优于小直径涡流管;冷孔板孔径愈小,涡流管的制冷制热效应都愈好,在冷孔板孔径与热端管内径之比为50%时,取得最佳的制冷制热效应。      

旋转条件下半封闭空间内多孔冲击平均换热特性实验

通过实验研究了冲击雷诺数Rej、旋转雷诺数Reω、以及冲击孔的排列方式、冲击孔到靶板之间的距离等参数,对旋转条件下半封闭空间内多孔冲击平均换热特性的影响.实验结果表明:随着冲击雷诺数的增大,多孔冲击的平均Nu数显著提高;随着旋转雷诺数的增大,平均Nu数稍有提高,但变化幅度不大;冲击孔的排列方式对平均换热效果也有一定的影响,叉排式稍优于顺排式;并且实验得出,冲击孔到靶板之间的距离为4倍冲击孔直径时多孔冲击平均换热效果最佳.     

智能化多传感器管理系统的设计和仿真

根据机载多传感器管理需求,提出了基于机载多传感器数据融合技术的智能化多传感器管理系统体系结构,并阐述了该系统的功能、系统设计原则和方法。采用商用货价产品技术(COTS)构建原型仿真平台,对提出的多传感器管理系统体系结构进行原型仿真,验证了该设计的有效性。     

航空发动机机匣摆线粗加工轨迹规划方法

针对机匣零件粗加工过程中凸台多、加工余量大、材料难切削、刀具磨损快、加工周期长等特点,提出了一种机匣摆线粗加工刀具轨迹规划方法,该方法能有效控制切削过程中刀具负载的变化,改善刀具切削过程中的加热-冷却循环,减缓刀具的磨损,提高机匣粗加工效率。首先,通过对两种摆线模型的分析,建立了摆线铣数学模型,并分析了摆线铣的优缺点;其次,结合机匣零件特点,将模型在精度范围内离散为点模型,利用圆锥将模型展开并建立展开模型与原始模型间的映射关系。通过对可加工区域的划分和平面逼近,生成了适用于机匣零件的摆线粗加工刀具轨迹。最后,分别通过摆线铣刀具磨损实验、平面型腔摆线铣实验和机匣摆线铣实验,验证了摆线铣在降低刀具磨损、延长刀具寿命方面的有效性,以及本文轨迹生成算法在航空发动机机匣实际加工中的正确性和高效性。研究成果能有效缩短加工周期、降低加工成本,提升机匣零件的粗加工效率。     

基于直升机舰面起降动态仿真的风限图计算

建立了基于直升机舰面起降动态仿真的风限图（WOD）计算方法,综合计入舰船尾流、直升机运动和驾驶员操控等多因素的作用提升风限图计算的准确度。基于耦合舰船非定常尾流的飞行动力学模型,发展了适于直升机多轴协同操控的驾驶员模型,建立了舰面起降轨迹的数学描述和生成方法,形成计入舰船尾流、直升机运动和驾驶员操控等多因素综合作用的直升机舰面起降动态仿真方法。在此基础上,总结风限图计算判据,建立风限图计算方法。计算结果表明,某些风况下直升机在舰面起飞和降落过程中受到舰船尾流的干扰远大于在甲板上方悬停时受到的作用。本文方法能够捕捉到不同起降点和起降方式导致舰船尾流时空变化的干扰,与传统计算方法相比,显著提升了风限图计算的准确度。     

Effects of yaw-roll coupling ratio on lateral-directional aerodynamic characteristics

Experimental investigation of large amplitude yaw-roll coupled oscillations was conducted in a low-speed wind tunnel using an aircraft configuration model. A special test rig was designed and constructed to provide different coupled motions from low to high angles of attack.A parameter ‘‘coupling ratio" was introduced to indicate the extent of yaw-roll coupling. At each pitch angle, seven coupling ratios were designed to study the yaw-roll coupling effects on the lateraldirectional aerodynamic characteristics systematically. At high angles of attack, the damping characteristics of yawing and rolling moments drastically varied with coupling ratios. In the coupled motions with the rotation taking place about the wind axis, the lateral-directional aerodynamic moments exhibited unsteady characteristics and were different from the ‘‘quasi-steady" results of the rotary balance tests. The calculated results of the traditional aerodynamic derivative method were also compared with the experimental data. At low and very high angles of attack, the aerodynamic derivative method was applicative. However, within a wide range of angles of attack, the calculated results of aerodynamic derivative method were inconsistent with the experimental data, due to the drastic changes of damping characteristics of lateral-directional aerodynamic moments with yaw-roll coupling ratios.     

A two-step weighted least-squares method for joint estimation of source and sensor locations: A general framework

It is well known that the Two-step Weighted Least-Squares(TWLS) is a widely used method for source localization and sensor position refinement. For this reason, we propose a unified framework of the TWLS method for joint estimation of multiple disjoint sources and sensor locations in this paper. Unlike some existing works, the presented method is based on more general measurement model, and therefore it can be applied to many different localization scenarios.Besides, it does not have the initialization and local convergence problem. The closed-form expression for the covariance matrix of the proposed TWLS estimator is also derived by exploiting the first-order perturbation analysis. Moreover, the estimation accuracy of the TWLS method is shown analytically to achieve the Cramér-Rao Bound(CRB) before the threshold effect takes place. The theoretical analysis is also performed in a common mathematical framework, rather than aiming at some specific signal metrics. Finally, two numerical experiments are performed to support the theoretical development in this paper.     

浅析民用飞机研制总体参数优化

分析了在概念设计阶段民用飞机总体设计工作内容和工作流程,并结合时下国外在用软件优缺点,构思了民用飞机总体设计参数综合优化的技术方案,包括优化设计架构、分析模型和优化算法等,为形成具有自主知识产权的民机总体设计综合分析和优化程序打下基础。