火箭发动机尾部结构优化研究

针对火箭发动机尾部壳体烧穿故障导致系统级失效的突出问题,运用贝叶斯网络模型推得影响系统可靠性的薄弱环节,结合试件性能与残骸分解数据,分析系统故障机理。采用有限元数值计算手段,由流场计算分析固定支架结构破坏后发动机内流场情况,进而明确系统结构优化方案。经结构优化考核试验,火箭发动机外壁温升降低62.17%,系统可靠性提高0.62%,实现可靠性增长的目的。     

CVD技术制备Ta/W层状复合材料

运用化学气相沉积(Chemical Vapor Deposition,CVD)技术制备了W体积分数分别10%,13%和18%的Ta/W两层层状复合材料,采用金相显微镜(OM)、扫描电镜(SEM)和室温拉伸实验对复合材料的性能进行分析。结果表明:运用CVD技术可以制备W体积分数不同,且密度优于理论密度99.4%的层状复合材料;复合材料中Ta,W层的晶粒均为柱状晶粒,离界面越近,晶粒越细;沉积态复合材料的力学性能优于纯CVD Ta和CVD W;1600℃×2 h的热处理后,复合材料的界面扩散层宽度显著增大,力学性能高于沉积态的力学性能,最高抗拉强度可达660 MPa。     

可折叠铍青铜弹性豆荚杆焊接成型工艺

可折叠铍青铜豆荚杆的焊接成型是该类豆荚杆研制的难点之一,本文对铍青铜豆荚杆的储能点焊工艺进行了研究,分析了工艺参数及热处理对焊接接头名义剪切强度的影响,给出了优选的工艺参数为焊接电压180 V、保压7 s。在最佳工艺条件下成型并经过340℃/2 h时效处理后,焊接接头的名义剪切强度由52 MPa提高到68 MPa。铍青铜焊接接头的名义剪切断口随着焊接电压的增大,从焊接接头区域向热影响区转移。     

基于DDPG-PID的机器人动态目标跟踪与避障控制研究

针对机器人在动态复杂环境下的操作问题,研究机械臂跟踪运动目标及避障的运动控制方法。采用传统PID控制方法与DDPG强化学习算法相结合的方式,利用PID控制使得机械臂的工作平面快速接近目标物并与之重合,再使用DDPG算法让机械臂在平面内自主学习追踪目标物投影同时避开障碍物投影,最终在三维空间中实现跟踪与避障。该方法将机械臂作为一个智能体,智能体通过感知目标物和障碍物的距离偏差来自主学习避障跟踪策略。将本方法用于多自由度机械臂路径规划与避障任务中,对比单纯使用DDPG算法将机械臂作为智能体在空间中进行决策控制,仿真结果显示本文所提出的方法收敛效果和控制性能更好,机械臂能在训练后实现目标物的稳定跟踪和障碍物的躲避。     

流动参数对发动机冷却用引射器性能的影响

为了探索引射器在航空发动机空气系统中的应用可行性,采用标准k-ω模型并求解雷诺平均Navier-Stokes方程组的数值方法,分析了流动参数对发动机冷却用引射器引射系数、压力损失系数及引射性能综合参数的影响.结果表明:膨胀比由9增大至10.1,引射系数增大了 66％;膨胀比由15.2增大至20.2,引射系数降低了 19...     

卫星通信干扰样式研究

综述通信对抗干扰的分类方式,分析了部分文献中对干扰样式划分的不合理性.根据卫星通信对抗的特点将通信对抗干扰样式进行分类,并从与压制式干扰相区别的角度对欺骗式干扰做出研究分析.     

高速BPSK相干光通信系统对激光器线宽要求

文章概述了激光器相位噪声对零差相干检测光通信系统性能的影响，对特定的基于平衡探测的科斯塔斯（Costas）环路接收系统相位误差进行了详细的理论分析，最后获得了不同传输码速率下的零差相干检测光通信系统对激光器线宽的具体要求。     

Measurements of heat transfer and pressure in a trailing edge cavity of a turbine blade

 An experimental investigation is conducted to obtain the heat transfer and pressure drop data for an integral trailing edge cavity test section that simulates a novel turbine blade's internal cooling passage with bleed holes. Local heat transfer is measured on both the suction and pressure sides by a transient liquid crystal technique, while pressures at six positions are recorded by pressure calibrators. Moreover, flow characteristic and its effect on heat transfer are analyzed for conditions with or without bleed flow. The experimental results show that, in the cases with bleed flow, local heat transfer on the pressure side exceeds that on the suction side in the first and second channels. In the cases without bleed flow, in the first and third channels, local heat transfer on the suction side weakens whilst it increases significantly on the pressure side. For the second channel, non-bleed condition leads to a more balanced heat transfer distribution between the upstream and downstream channel. Besides, after the bleed holes are blocked, heat transfer in the first bend region on the suction side declines sharply, while the opposite phenomenon occurs for the second bend region on the pressure side. In both bleed and non-bleed cases, the total pressure of six measurement positions decreases continuously along the channel at the same Reynolds number and it promotes for higher Reynolds number. Among all the measurement points, under the same flow rate condition, the highest speed occurs at Position 5, which also shows the maximum difference between the total and static pressures. When the bleed holes are blocked, the total pressure at each measurement position appears to increase.     

关于进行程序管制一体化模拟练习的设想

在程序管制模拟练习中，存在着塔台管制服务、进近管制服务和区域管制服务互不衔接，不能系统地模拟整个管制过程的问题。针对这一情况提出了程序管制一体化模拟练习和程序和管制一体化模拟机的结构设计。     

Fuel Savings in the WHECON Attitude Control System Using an Asymmetric Controller

This paper investigates the possibility of generating an on-off limit cycle mode in the WHECON attitude control system. lt is shown that, by eliminating the off set angle ? in the roll-actuated control torquer, the WHECON system can be reduced to the structure considered earlier by Mendel and, therefore, an on-off limit cycle can be generated simply by introducing an appropriate amount of asymmetry into the deadzone characteristic of the WHECON controller. Because with this mode of on-off limit cycle the thruster jets will fire only once in each cycle of the oscillation, it is claimed that a considerable amount of fuel can be saved by the proposed modifications to the original WHECON design. Dynamic simulation study was conducted with the actual nonlinear model of the WHECON system considered and the results indicate that, for both zero and nonzero values of the off set angle ?, substantial fuel savings can be achieved by using the asymmetric controller.