The influence of microgravity on invasive growth in Saccharomyces cerevisiae

This study investigates the effects of microgravity on colony growth and the morphological transition from single cells to short invasive filaments in the model eukaryotic organism Saccharomyces cerevisiae. Two-dimensional spreading of the yeast colonies grown on semi-solid agar medium was reduced under microgravity in the Σ1278b laboratory strain but not in the CMBSESA1 industrial strain. This was supported by the Σ1278b proteome map under microgravity conditions, which revealed upregulation of proteins linked to anaerobic conditions. The Σ1278b strain showed a reduced invasive growth in the center of the yeast colony. Bud scar distribution was slightly affected, with a switch toward more random budding. Together, microgravity conditions disturb spatially programmed budding patterns and generate strain-dependent growth differences in yeast colonies on semi-solid medium.     

Exploration and protection of Europa's biosphere: implications of permeable ice

Europa has become a high-priority objective for exploration because it may harbor life. Strategic planning for its exploration has been predicated on an extreme model in which the expected oceanic biosphere lies under a thick ice crust, buried too deep to be reached in the foreseeable future, which would beg the question of whether other active satellites might be more realistic objectives. However, Europa's ice may in fact be permeable, with very different implications for the possibilities for life and for mission planning. A biosphere may extend up to near the surface, making life far more readily accessible to exploration while at the same time making it vulnerable to contamination. The chances of finding life on Europa are substantially improved while the need for planetary protection becomes essential. The new National Research Council planetary protection study will need to go beyond its current mandate if meaningful standards are to be put in place.     

高密度航空电子设备的液冷方法

新一代飞机将要求航空电子设备能以更小的体积提供更为优越的系统性能。这一要求导致在各级电子包装上产生高的功率密度。由于没有新的热管理方法，元件结温将显著升高，从而导致可靠性的严重下降，在某些情况下，甚至导致元件功能的失效。为满足改进热管理的要求，已开发出一种液冷方法来代替高功率场合的常规空气冷却法。已经研制出液冷机架和液流通过模块，使结温限制到可以接受的程度。液冷也延长了冷却液损失后应急工作的时间，这对飞行关键设备而言是需要的。目前的活动着重子开发液冷机架和模块，这对综合航空电子系统联合工作组（ＪＩＡＷＧ）管理的国防部（ＤＯＤ）两级维护的创立是个有力的支持。     

带加速度修正的极坐标系α-β滤波器

有时使用极坐标系对跟踪计算很有利。但因匀速目标的位置量不再象直角坐标系中一样是时间的线性函数而带来了复杂。然而这可以通过使用在预报方程中加伪加速度修正因子来近似修正系统动态的方法而解决,代价是增加了系统的噪声。对于α-β滤波器,加入这些修正因子,滤波器的稳态误差性能降低极小,同时又可大大减小偏倚误差。     

用于冷、热杂波综合抑制的最佳降秩三维空时自适应处理

本文提出了一种新的信号处理策略，它采用最佳的与信号有关的降秩来解决三维STAP（空时自适应处理）冷、热杂波抑制问题。虽然只采用空间（角度）PRI时间（多普勒）自由度，常规的二维STAP也能抑制单站（“冷”）杂波和直接路径干扰，然而，要抑制由干扰源地形散射干扰造成的所谓“热”杂波，还需要附加“快时间”自由度（在接收机带宽的倒数量级上）。引入了三维旁瓣对消器（Wiener滤波器）的多级分解，以评估降秩的理论性能限，并验证采用这种方法获得紧密干扰压缩的可能性比主分量方法获得的可能性最大。采用基于DTED测量的高保真模拟数据集合说明了3D STAP的多级Wiener滤波方法的功效。     

孔、轮廓和表面(十一)

第七章座标镗床的运行操作(二) 尺寸测量——工件对机床运动方向的方位一经找正,下一步则要求建立工件相对于机床测量系统及主轴轴线的尺寸关系。调整刻度盘或者工作台时,应该总是沿着刻度盘上箭头所示方向运动,以免产生间隙。如需再次回到调整位置,必须首先退离该处千分之几英寸(约百分之几毫米),然后再按照     

航天飞机时频传递实验

一、引言 1.背景美国航空航天局(NASA)的空间和地面应用处正在考虑一项航天飞机实验,用来验证几种比对全球高精密时钟和原始频标的技术。该实验准备在航天飞机上装一台氢脉泽时钟,利用微波和激光脉冲信号比对航天飞机上的空间时钟与地面站上的时钟。提出该项实验的目的是验证几种时间传递技术,这些技术能以1毫微秒以上的精度比对时钟时间,以10~(-14)以上的精度比对时钟频率。能以10~(-14)的精度比对频率这种能力是本项实验的独到之处。目     

玻璃碳断裂性能的一些研究

本文简要介绍用“声共振法”测材料的杨氏模量,用“控制裂纹法”测材料的断裂韧性以及材料的极限应变能释放率的计算。对三种玻璃碳的室温-1023°K的杨氏模量和断裂韧性进行了测定,用电子扫描显微镜对玻璃碳的断裂、氧化和加工表面进行研究观察,分析了玻璃碳的极限应变能释放率并与多晶石墨及碳-碳复合材料进行比较。     

电子束淬火（续二）

这是本课题三篇系列论文的最后一篇,概述了电子束淬火的效能和优点。对电子束淬火在工程技术领域内的实际应用,也作了详尽的阐述。 本文的前两部分分别刊登于本刊91年第2期和第3期。     

MArs Neutron Energy Spectrometer (MANES): an instrument for the Mars 2003 Lander

We describe the instrument design and detector development for MANES which has been selected to fly on the Mars 2003 Lander. Section 1 explains the need for the spectrometer in determining the increased risk of carcinogenesis for astronauts. Section 2 presents the instrument design including an outline drawing, a cross-sectional view and a detailed block diagram. Sections 3 and 4 describe the low and high energy detector components of the spectrometer and present responses to monoenergetic neutron beams. Sections 5 and 6 explain the design approaches to charged particle discrimination and instrument transfer function modeling.