匀速及加速行驶直背式轿车气动噪声

应用计算流体力学软件FLUENT对简化直背式轿车外部流场及车外某接收点处气动噪声进行了数值计算和分析.脉动流场计算采用大涡模拟湍流模型,动量方程的离散格式采用有限中心差分格式.分别对两种匀速运动情况和一种加速运动进行了计算,由此研究不同车速、匀速和加速运动对接收点处脉动流场和气动噪声的影响.对于匀速运动,车速越大,接收点处流速越大,压力越小,在每个频率上所对应的声压级基本上越大,总声压级也越大;在同一行驶速度下,加速运动比匀速运动在接收点处的流速要大,压力要小,在每个频率上所对应的声压级基本上要大,总声压级要大,声压级随频率的变化情况与匀速运动一样.      

ZSGA?2型重力敏感器关键技术分析与试验验证

与国外主流海洋重力仪相比,国产海洋重力仪的分辨率低一个数量级,这制约了国产海洋重力仪的应用。针对国产海洋重力仪亟需提高分辨技术的需求,根据ZSGA-2型重力敏感器的工作原理,建立了弹性系统的力学模型,并开展了样机的静态性能测试。测试结果表明,经零位漂移和大地固体潮汐修正后的静态精度达到了0.03mGal,样机随重力仪进行楼层高差测量的重复性为0.15mGal。该型重力敏感器的分辨率已经达到了国外同类产品的技术水平,并具备了一定的动态适应性,为该型高分辨率零长弹簧重力敏感器开展高动态环境适应性技术研究奠定了坚实基础。     

合理运用SI技术快速收敛高速数字电路设计

随着数字电路集成度和工作频率的不断提高,信号完整性(Signal Integrity, SI)问题在产品研制过程中越来越突出。以惯导系统中的某导航计算机为例,针对故障信号回路,使用仿真软件对其SDRAM时钟信号进行信号完整性仿真,并进行优化设计。通过对比优化前和优化后的仿真与测量结果,验证了由于端接参数不匹配造成SDRAM时钟信号的非单调性畸变问题。仿真与测量结果表明,在产品研制流程中加入信号完整性仿真环节有利于设计快速收敛,提前规避风险,缩短研发周期,降低设计成本,提高电路产品的可靠性和电磁兼容性。     

涡轴发动机发展与技术趋势

首先,对美国20世纪70年代以来各时期涡轴发动机发展规划及其性能演变过程进行了梳理,并分析了不同循环类型及循环参数的选择,进行了性能统计分析。然后,介绍了直升机/发动机一体化设计理论的基础与方法。最后本文提出新一代超低排放涡轴发动机的概念,指出降低总耗油量的同时提高功重比,才能实现超低排放。     

碳纤维加筋板的超声相控阵C扫描检测可靠性研究

碳纤维加筋板结构在现代航空器中被大量应用,超声波相控阵C扫描技术是这类结构在役环境下的有效检测手段之一,被广泛应用。对于同一个损伤,在实际检测中会出现从不同的方向检测结果不一致的现象;这种现象在传统单点超声波C扫描检测中是不会发生的。本文从试验件表面曲率、缺陷特性等方面对这种不一致性进行了分析和探讨,并给出了避免这一类不确定性发生的建议。     

电连接器接点焊接工艺研究

针对航天产品电连接器接点焊点与引线断裂失效问题,分析了焊接过程中助焊剂、焊料、焊接工具和防护套等对接点焊接质量的影响。结合实践经验,提出相关工作参数和材料的选取原则,确定了生产中焊接技术的质量控制点。     

侧风环境下行驶的直背式轿车气动力计算

分别对直背式简化轿车模型在无侧风、稳态侧风、非稳态侧风三种条件下汽车周围流场进行了数值模拟,并对汽车受到的气动力进行了计算.结果表明,定常侧风会产生较大侧向力,阻力和升力也有一定增加;在非定常侧风作用下,气动力变化趋势与侧风速率变化趋势基本相同.阻力增大幅度较为平缓,侧向力增大较为显著,升力处于两者之间.当侧风增大到一定速率后,车外流场会发生较大变化,尾涡会转变为侧向涡.      

Numerical Study of Parachute-Payload Land Site Distribution with Randomize Wind Gust Model

A parachute-payload model with randomize wind gust is developed to study the landing accuracy of the parachute decelerator system,which can be exactly described by the landing site distribution.The research focuses on the steady descent phase of the parachute descent process,so the parachute and the payload suspension formulation during the phase are mainly discussed.In addition,since the wind effects have a significant impact on the land site distribution of the passive decelerator system and it is difficult to obtain the exact wind profile in practice,major features of parachute-payload system are studied via the randomized wind gust formulation.As the randomized wind gust formulation is adopted,the wind effect can be considered without the exact wind gust profile and the parachute aerodynamic simulation can be fulfilled with uncertainties.Finally,the model is validated and discussed,and the parachute land site distributions with different wind randomize profiles are presented for comparison.The results show that when parachute is less stable,the land site tends to have a larger variance.     

一种基于元路径拥塞模式挖掘的移动对象位置预测方法

路网上移动对象位置预测是许多位置相关服务的基础。目前移动对象位置预测方法没有充分考虑到轨迹数据中所蕴含的道路拥塞信息,而路网上的道路拥塞状态对移动对象的位置更新会产生巨大影响。提出基于元路径拥塞模式挖掘的方法(Meta-congestion-pattern mining,MCPM)。在离线挖掘阶段,从历史轨迹的频繁路径(元路径)的紧集中挖掘当地的拥塞模式,并对运动模式进行建模,其中采用基于k均值的聚类算法解决数据稀疏性问题。在线预测阶段根据挖掘的拥塞模式和运动模式依概率进行预测。最后通过理论分析和实验验证得出了算法的有效性,与相同条件下的精度预测(WhereNext,WN)方法相比,平均预测准确性提高了近20%,预测时间平均缩短了近50%。     

PARAMETER ANALYSIS ON CIRCULATION CONTROLLED CIRCULAR CYLINDER FOR NOTARTM TAIL BOOM

Lift on circulation control （CC） circular cylinder is calculated via numerical simulations based on 2D real- izable k-e epsilon viscous model and compared with experimental data. The simulation result shows an acceptable agreement with tested data. With the proved grid and simulation method, series of simulations are conducted to study the effect of parameters on lift. Single slotted tail booms under different clown wash velocities are optimized with the principle of generating maximum total moment around the main rotor shaft with same total power con- sumption. The results show that larger jet flow velocity, or smaller blow angle, or larger diameter of the cross section can help generating larger lift while enhancing the attachment of both the jet flow and down wash flow. Multiple slotted tail boom is better because it increases lift with same total slot width, and can increase lift by in- creasing total slot width without causing separation, also it helps generating high steady lift at a big rank of slot at- tack angles. To mount a guide vane （GV） at the exit of the slot, or shape the upper slot wall like a smooth-GV, or design the slot with an edge fillet is not recommended because it reduces the velocity of both the jet flow and the upstream of the attached downwash flow. Compared with other shapes of the slots, arcs-profiled slot performs better because of larger jet flow velocity and smaller blow angle. In order to generate the largest moment with same total power consumed by the entire NOTARTM system, total width of the slots and slot attack angle should be optimized according to velocity of down wash flow.