Enhancing the ATIC charge resolution

The Advanced Thin Ionization Calorimeter (ATIC) experiment is designed to investigate the charge composition and energy spectra of primary cosmic rays over the energy range from about 10¹¹ to 10¹⁴ eV during Long Duration Balloon (LDB) flights from McMurdo, Antarctica. Currently, analysis from the ATIC-1 test flight and ATIC-2 science flight is underway and preparation for a second science flight is in progress. Charge identification of the incident cosmic ray is accomplished, primarily, by a pixilated Silicon Matrix detector located at the very top of the instrument. While it has been shown that the Silicon Matrix detector provides good charge identification even in the presence of electromagnetic shower backscatter from the calorimeter, the detector only measures the charge once. In this paper, we examine use of the top scintillator hodoscope detector to provide a second measure of the cosmic ray charge and, thus, improve the ATIC charge identification.     

CREAM: 70 days of flight from 2 launches in Antarctica

The Cosmic-Ray Energetics And Mass balloon-borne experiment has been launched twice in Antarctica, first in December 2004 and again in December 2005. It circumnavigated the South Pole three times during the first flight, which set a flight duration record of 42 days. A cumulative duration of 70 days within 13 months was achieved when the second flight completed 28 days during two circumnavigations of the Pole on 13 January 2006. Both the science instrument and support systems functioned extremely well, and a total 117 GB of data including 67 million science events were collected during these two flights. Preliminary analysis indicates that the data extend well above 100 TeV and follow reasonable power laws. The payload recovered from the first flight has been refurbished for the third flight in 2007, whereas the payload from the second flight is being refurbished to be ready for the fourth flight in 2008. Each flight will extend the reach of precise cosmic-ray composition measurements to energies not previously possible.     

Gamma-ray detector on board lunar mission Chang’E-1

Gamma-ray spectrometer (GRS) is included in the payload of Chinese first lunar mission Chang’E-1 that will be launched in 2007. Specific objectives of the GRS are to map abundance of O, Si, Fe, Ti, U, Th, K, and perhaps, Mg, Al, and Ca to depths of about 20 cm. There are remarkable advantages for GRS application to remote sensing elemental materials over the entire lunar surface: large effective area and good ability for background rejection. We will describe the design of GRS and present its performance in this paper. Moreover, the GRS calibration will also be introduced.     

Analysis of dynamics of a passive line-of-sight stabilization system with four-axis gimbal suspension

A mechanical model of the line-of-sight stabilization system for the optical device mounted on a movable carrier vehicle is considered. The nonlinear Lagrange equations of motion for a four-axis gimbal suspension are derived. Requirements on design and parameters for the passive line-of-sight shock absorption system of the optoelectronic payload are worked out.     

Route optimization of the aircraft flight

A method of finding the aircraft optimal route by means of task-oriented replacement of the functional being optimized is proposed.     

Weight effects on the periodic ambiguity function

CW radar signals and processors are discussed. The use of the periodic ambiguity function (PAF) to analyze the delay-Doppler performance of CW signals and their corresponding correlation receivers, is extended to include weight function effects. This work provides tools which can predict the delay-Doppler response of almost any phase-coded CW radar. Examples demonstrate that a combination of CW signals having perfect periodic autocorrelation, a matched reference signal with a large number of modulation periods and a smooth weight function, can create a delay-Doppler response with extremely low sidelobes, strongly resembling the response of a coherent pulse train     

An efficient SAR parallel processor

A parallel architecture especially designed for a synthetic-aperture-radar (SAR) processing algorithm based on an appropriate two-dimensional fast Fourier transform (FFT) code is presented. The algorithm is briefly summarized, and the FFT code is given for the one-dimensional case, although all results can be immediately generalized to the double FFT. The computer architecture, which consists of a toroidal net with transputers on each node, is described. Parametric expressions for the computational time of the net versus the number of nodes are derived. The architecture allows drastic reduction of the processing time, preserving elaboration accuracy and flexibility     

Mathematical modeling of response of ecosystems with different structure to external impact.

A mathematical model was used to study the response of ecosystems of different structures to external impact. The response was measured as a sensitivity coefficient: the magnitude of the system's response vs. the change of the factor in the inflow. The formula has been obtained to calculate the sensitivity coefficient for ecosystems containing different numbers of trophic links. The derived sensitivity coefficients demonstrate that the degree of compensation for the external impact can differ depending on the type of system regulation and the length of the trophic chain. E. g. the sensitivity coefficient decreases with complexity of trophic links in an ecosystem for top-down controlled systems and impact of degree of openness on sensitivity e.g. closed ecosystems show higher sensitivity then fully open ecosystem to impacts also bottom-up control system show less sensitivity then top-down. Grant numbers: N99-04-96017, N25.     

Thermal fatigue in structural components of flying vehicles engines

The paper deals with the problems of deformation and damage of the materials of structural components of complex shape subjected to cyclic loading by convective thermal flows which induces in them non-uniform temperature and thermal-stress fields. A new testing technique is proposed employing the use of models of different shape and, in particular, those of wedge-shape prism type. Variation of the level of thermal stresses and temperatures, as well as of the degree of non-uniformity of temperature and stress fields, is effected by changing the models dimensions under the given thermal loading conditions. It is shown that in simultaneous testing of a great number of models of different size it is possible to obtain information sufficient for deriving the equations of the material state under complex thermo-mechanical loading in aggressive gas flows. Examples are presented of practical application of the technique proposed.