钛合金表面镍包石墨喷涂层的耐磨性能

为了提高钛合金的表面耐磨性,利用氧乙炔热喷涂枪,在TC4合金表面上制备出镍包石墨涂层。采用MXP-2000型销盘式摩擦磨损实验机,进行钛合金及其镍包石墨涂层的干摩擦磨损实验,并利用扫描电镜对磨损表面进行观察和分析。实验结果发现,镍包石墨涂层的摩擦系数只有钛合金的一半左右,前者磨损量为后者的1/6,说明镍包石墨涂层可以大大提高钛合金的表面耐磨性能。TC4合金的磨损机制以黏着磨损为主,喷涂层的磨损机制以磨粒磨损为主,喷涂层中的石墨润滑相是其耐磨性高的主要原因。     

空载固体发动机计算与试验模态相关性分析

为了预测空载状态固体火箭发动机动态特性,对其进行了模态试验,并应用MSC.Marc进行了模态计算,然后对比两者的结果,进行了相关性分析和评估。计算得到了发动机250Hz以内的一阶弯曲模态和五阶呼吸模态。试验测得了发动机的三阶呼吸模态和一阶弯曲模态。比较试验测试模态和与之对应的计算模态:固有频率相对误差均在5%以内;振型相关图上的点大都分布在斜率为1(或 1)的直线周围;MAC(模态置信判据)值在0 9左右。说明计算与试验模态有较好的相关性,有限元计算模型比较准确的反映了实际情况。     

An innovative study on low surface energy micronano coatings with multilevel structures for laminar flow design

Laminar flow design is one of the most effective ways to reduce the drag of a commercial aircraft by expanding the laminar flow region on the surface of the aircraft. As material science develops, the emergence of new materials such as low surface energy materials has offered new choices for laminar flow design of commercial aircraft. Different types of low surface energy micro-nano coatings are prepared to verify the effects on the boundary layer transition position and the drag of the airfoil through wind tunnel tests. The infrared thermal imaging technology is adopted for measuring the boundary layer transition, while the momentum integral approach is employed to measure the drag coefficient through a wake rake. Infrared thermal imaging results indicate that the coatings are capable of moving backward the boundary layer transition position at both a low velocity of Mach number 0.15 and a high velocity of Mach number 0.785. Results of the momentum integral approach demonstrate that the drag coefficients are reduced obviously within the cruising angle of attack range from 1° and 5° by introducing the low surface energy micro-nano coating technology.     

A general calculation method to specify center-of-buoyancy for the stratospheric airship with multiple gas cells

As the lighter-than-air (LTA) flight vehicle, the stratospheric airship is a desirable platform to provide communication and surveillance services. During the ascent from sea-level to the mission altitude, the volume of the lifting gas may change significantly, which will result in the change of the center-of-buoyancy (CB). A general calculation method is developed to specify CB for the stratospheric airship with a double-ellipsoid hull and an arbitrary number of the gas cells. The cross-section-integral (CSI) method is used as a basic calculation scenario to specify CB. Considering the complexity in determining the boundary between the helium and air in the gas cell, a searching algorithm is put forward and the specification of CB can be conducted by the iterative calculation. As an important application, the stable condition of the pitch angle is analyzed when the change of CB is involved. Under different initial configurations, the stable pitch angle of the stratospheric airship during the ascent is specified and compared, which shows the advantages of the multi-gas-cell configuration. The results of this paper may provide an important reference for the engineering application of the stratospheric airship.     

Structure and kinetic properties of slow-mode shocks associated with magnetic reconnection in the near-Earth magnetotail

We study the structure and kinetic properties of slow-mode shocks near the plasma sheet boundary layer (PSBL) associated with magnetic reconnection by Cluster observation. The presence of slow-mode shocks is confirmed by traditional Rankine–Hugoniot (RH) analysis and Monte-Carlo shock fitting method. The Walén analysis, applied to the tailward flow associated with slow-mode shocks, also supports that plasma was accelerated across a Petschek-type slow-mode shock connected to the diffusion region. Back-streaming ions were observed on the shock layer, and cold ions were accelerated and heated by slow-mode shocks. In addition, whistler and electrostatic solitary waves were observed around the slow-mode shocks. These waves might be excited by the observed field-aligned electron beams near the shocks.     

专用瞄准设备自动检定系统

介绍了专用瞄准设备自动检定系统的系统配置、工作原理及软件设计，并对系统的测量不确定度进行了分析和评定。     

高精度温度控制方式述评

对高精度温度控制系统中常用的模拟控制方式、数字控制方式和模拟/数字控制方式作了比较,目的在于找到既能满足计量检定恒温装置所需的技术指标、又方便实用的控制方式.     

遥感卫星扰振对TDICCD相机图像影响的仿真与分析

随着传输型遥感卫星结构的扩大化及灵活性的增强,对图像品质产生影响的扰振越来越受到重视。当遥感卫星在轨进行成像时,相机的图像品质会由于星上活动部件的运动的影响而下降。文章从调制传递函数（Modulation Transfen Function,MTF）角度出发,对不同工况下太阳翼转动驱动机构（BAPTA）和动量轮对图像品质的影响进行了仿真和评估。同时,针对高分辨率相机成像品质影响,从动力学仿真方面对星体扰振的幅值和频率进行了有限元分析,确定了扰振源的频率和幅值。最后,根据仿真分析结果,提出了星上扰振控制方案建议。