三级轴向旋流燃烧室流场结构研究

为深入了解燃烧室内流场,研究不同来流状态对燃烧室流场结构的影响,基于粒子成像速度仪(PIV)技术,对采用三级轴向旋流器的航空发动机燃烧室进行流场测量,分别在Case 1常温低压(0.49MPa)、Case 2常温中压(0.98MPa)、Case 3常温高压(1.64MPa)、Case 4全状态(高温813K高压2.78MPa)来流条件下进行。研究结果表明,同一燃烧室模型在不同速度、温度和压力来流下有基本相同的流场结构,但在中心回流区尺寸、角落回流区尺寸、主燃孔和掺混孔射流等细节方面仍有明显差异,来流压力较高的流场中心回流区向下游扩展更深入,角落回流区被压缩,主燃孔和掺混孔射流速度增加且进气比例增大。     

Space Weather Service for Chinese Space Science Satellites

Strategic Priority Research Program on Space Science has gained remarkable achievements. Space Environment Prediction Center (SEPC) affiliated with the National Space Science Center (NSSC) has been providing space weather services and helps secure space missions. Presently, SEPC is capable to offer a variety of space weather services covering many phases of space science missions including planning, design, launch, and orbital operation. The service packages consist of space weather forecasts, warnings, and effect analysis that can be utilized to avoid potential space weather hazard or reduce the damage caused by space storms, space radiation exposure for example. Extensive solar storms that occurred over Chinese Ghost Festival (CGF) in September 2017 led to a large enhancement of the solar energetic particle flux at 1 AU, which affected the near Earth radiation environment and brought great threat to orbiting satellites. Based on the space weather service by SEPC, satellite ground support groups collaborating with the space Tracking, Telemetering and Command system (TT&C) team were able to take immediate measures to react to the CGF solar storm event.      

Modeling and experimental validation of sawing based lander anchoring and sampling methods for asteroid exploration

This paper presents a novel lander anchoring system based on sawing method for asteroid exploration. The system is composed of three robotic arms, three cutting discs, and a control system. The discs mounted at the end of the arms are able to penetrate into the rock surface of asteroids. After the discs cut into the rock surface, the self-locking function of the arms provides forces to fix the lander on the surface. Modeling, trajectory planning, simulations, mechanism design, and prototype fabrication of the anchoring system are discussed, respectively. The performances of the system are tested on different kinds of rocks, at different sawing angles, locations, and speeds. Results show that the system can cut 15?mm deep into granite rock in 180?s at sawing angle of 60°, with the average power of 58.41?W, and the “weight on bit” (WOB) of 8.637?N. The 7.8?kg anchoring system is capable of providing omni-directional anchoring forces, at least 225?N normal and 157?N tangent to the surface of the rock. The system has the advantages of low-weight, low energy consumption and balance forces, high anchoring efficiency and reliability, and could enable the lander to move and sample or assist astronauts and robots in walking and sampling on asteroids.     

考虑磨损后含间隙指向机构运动特性

为了提高空间指向机构磨损寿命的预测精度,克服传统静态磨损寿命预测的缺陷,计及间隙、摩擦磨损耦合因素,以实现机构关节动态磨损的精确预测,并对综合考虑间隙、摩擦磨损等因素的空间二维指向机构动力学问题和磨损问题进行了研究。采用牛顿 欧拉法,将间隙变量嵌入动力学模型,构建含间隙二维指向机构的动力学模型。基于Archards磨损模型,找到运动副接触面不同位置处的磨损深度,重构运动副表面形貌,并对磨损前后含间隙指向机构的动态特性进行分析,得到了关节处接触碰撞力和切向摩擦力的变化规律;采用动态拟合变量法和离散处理法分别对含间隙运动副内部间隙与接触力间、运行时间与相对滑移速度间的对应关系进行拟合,并建立了动态磨损数学模型;进一步预测了二维指向机构在跟踪模式、调姿模式下的运行时间分别为1259192h、76444h。研究工作为二维指向机构的本体设计、制造与应用奠定基础。     

Method for designing constant thrust power schedule

In order to make the power level angle (PLA) have the same bijection relationship with the thrust when the environment changes before operational limit exceedance, and ensure the pilots ability of unrestricted throttle movement as well as the safety of the engine, a method used to design a constant thrust power schedule was proposed. The research was based on a simulink turbofan engine model and the results were organized as look-up tables in different structures with limitations. Simulation was done to confirm the validity and demonstrate the effectiveness of the schedule obtained with the approach. The constant thrust takeoff schedule, constant thrust idle schedule and constant thrust part power schedule with the present constant thrust control (CTC) method were proved to be valid. The results can be applied to this specific engine but the method can be applied to any areoengine and can be even extended to the unmanned plane.      

一种小型化宽频带微带阵列天线设计

介绍一种小型化宽频带微带阵列天线设计,采用矩形渐变切角结构和E 型开槽结构,实现微带天线 的宽带化和小型化。馈电网络采用多级并联式T 型功分网络,保证宽频带馈电形式。基于项目需求设计、加 工了一套4×6 单元的微带阵列天线,测试结果表明,该天线在10% 的频带内反射系数优于-10dB,增益大于 20dBi。     

轴向间距对压气机通道堵塞及总性能的影响

为了研究转静子叶片排之间的轴向间距对压气机内部流动堵塞及气动性能的影响,选取某单级轴流压气机为研究对象,采用多通道非定常数值计算方法对其5种不同轴向间距下的内部流场进行了全三维数值模拟。结果表明:在每一种轴向间距下,当压气机节流至某一工况之后,压气机通道内的流动堵塞区主要集中在转子叶顶间隙区域和动叶吸力面尾缘附近以及静叶吸力面轮毂角区内;在同一流量下,随着轴向间距的减小,转子叶根吸力面尾缘处的流动堵塞区有所扩大,但转子叶顶间隙区域及静叶吸力面轮毂角区内的流动堵塞区体积却不断减小,压气机通道内回流区的总体积也随之减小,其结果是压气机的静压升能力和流动稳定性增强且效率增大。通过进一步研究发现:在同一流量下,当轴向间距减小时,转子叶顶间隙区域内的主流轴向动量增大且泄漏流的轴向动量减小,其结果是转子叶顶间隙区域内流动堵塞区的体积减小。