亚声速叶片与跨声速叶片的气动阻尼比较

为了研究叶轮机中叶片与流场流固耦合作用情况下的气动阻尼,分别以亚声速和跨声速转子叶片为例计算气动阻尼。根据对非定常气动力的分析,提出了一种与结构等效粘滞阻尼比对应的模态气动等效粘滞阻尼比的定义。采用弱耦合分域求解的算法,在线性范围内,计算并比较了跨声速叶片和亚声速叶片模态和振幅对模态气动阻尼比的影响,根据分布气动阻尼比研究压缩波对模态气动阻尼比的影响。研究结果表明这两类叶片的气动阻尼特性基本一致,所提参数对两类叶片的气动阻尼的影响基本相同。     

Study on dynamic stiffness of supporting structure and its influence on vibration of rotors

The dynamic response of the rotor depends on not only itself but also the dynamical characteristics of the structures that support it. In this paper, the coupling vibration characteristics of the rotor and supporting structure are studied using one simple rotor-supports model firstly, and then the dynamic stiffness of the typical supporting structure of an aero-engine is investigated in use of both numerical and experimental methods. While, one simulation strategy is developed to include dynamic...     

Energy-optimal trajectory planning for solar-powered aircraft using soft actor-critic

High-Altitude Long-Endurance(HALE) solar-powered Unmanned Aircraft Vehicles(UAVs) can utilize solar energy as power source and maintain extremely long cruise endurance,which has attracted extensive attentions from researchers. Trajectory optimization is a promising way to achieve superior flight time because of the finite solar energy absorbed in a day. In this work,a method of trajectory optimization and guidance for HALE solar-powered aircraft based on a Reinforcement Learning(RL) framework is...     

《诗经》中女性生命价值的解读

中国的伦理文化中,对母性的塑造一方面是对"女色"的危害进行严惩,另一方面是对女性进行引导,使她们能够按照指定的方向行进,最终使所有的女性都安于贤妻良母的价值规范。透过《诗经》及后世对《诗经》的解读即可看出男性对女性的价值期待。     

我的名字叫“玉兔”——记中国首辆月球车征名始末

全民参与的征名 月球车征名活动于2013年9月25日开始，为使中国第一辆月球车的名称能够充分体现全国人民乃至全球华人的意愿，富有时代性、民族性、群众性的特色，活动通过新华网、腾讯网等方式向全国以及全球华人发出邀请。活动开始后，作品将经过提交、初评入围、网上投票、终审评审、上报批准五个阶段。月球车征名活动的原定投票时间为6天，     

Fabrication of Diamond-like Carbon Films by Ion Assisted Middle Frequency Unbalanced Magnetron Sputtering

Diamond-like carbon （DLC） films are deposited by the Hall ion source assisted by the mid-frequency unbalanced magnetron sputtering technique. The effects of the substrate voltage bias, the substrate temperature, the Hall discharging current and the argon/nitrogen ratio on the DLC film＇s performance were studied. The experimental results show that the film＇s surface roughness, the hardness and the Young＇s modulus increase firstly and then decrease with the bias voltage incrementally increases. Also when the substrate temperature rises, the surface roughness of the film varies slightly, but its hardness and Young＇s modulus firstly increase followed by a sharp decrease when the temperature surpassing 120 ℃. With the Hall discharging current incrementally rising, the hardness and Young＇s modulus of the film decrease and the surface roughness of the film on 316L stainless steel firstly decreased and then remains constant.     

Observations of TEC Depletion,Periodic Structure of TEC,ROTI and Scintillation Associated with ESF Irregularities over South China

The observations of Global Positioning System (GPS) scintillation, Total Electron Content (TEC) depletion, the periodic structure of TEC and Rate of TEC Index (ROTI) over south China were presented. Data were collected from GPS observations at stations of Shenzhen and Guangzhou from 2011 to 2012. This study reported that the ratio of simultaneous occurrences of TEC depletions with strong scintillations was higher than that of TEC depletions with weak scintillations in vernal and autumnal equinoxes of 2011 over South China. The number of the periodic structures of TEC with depletion contained was greater than that with no depletion contained corresponding to strong scintillations. The structure of the slab of plasma irregularities could be responsible for the simultaneous occurrences of TEC depletion with strong scintillations and ROTI. Before and during the occurrences of strong scintillation, there was Large-Scale Wave Structure (LSWS) which provided the seed ionization perturbation to trigger ESF irregularities and contributed to the periodic structure of TEC.      

飞机部件智能柔性精加工技术研究

为保证飞机部件在对接面处接头及外形的协调准确度,在传统的部件精加工工艺中,广泛采用了产品数据→标准样件→专用刚性精加工型架的传递体系,其协调路线长、环节多、协调关系复杂、工装无通用性、工装制造周期长的特点,不能适应产品的批量小、品种多、更新快的形势。通过对比分析各种精加工技术,提出在精加工技术中的数字化、智能化应用研究,可满足结构尺寸在一定范围内所有飞机部件的精加工需求。