铝合金壳体阳极化膜颜色异常分析

铝合金壳体在阳极化处理后表面阳极化膜存在颜色异常(发黑)现象。本文通过对壳体阳极化膜表面及基体形貌观察、金相分析和成分分析对发黑的原因进行了分析。结果表明壳体阳极化膜发黑的原因是由于该区域存在成分偏析(合金含量高),导致该区域的晶粒尺度比正常区域小、耐蚀性比正常区域差,膜层微观结构与正常区域存在差异,膜层内部化合物较多,致使该区域膜层呈现黑色。     

热障涂层在涡轮叶片应用中的热防护有效性

建立了含热障涂层的涡轮叶片简化传热模型,通过理论推导建立了热障涂层的有效性判据,并基于此进行了热防护有效性分析。理论分析与数值实验表明:由热障涂层带来的复合传热表面传热系数的变化会显著影响热障涂层的热防护效果;在发动机典型工况下,对于处于高温区的高压涡轮叶片前缘处,热障涂层引起的复合传热表面传热系数变化率最大值的范围为1.25%~10.83%以满足热防护有效性要求。在工程中应特别注意由于热障涂层的应用带来的复合传热表面传热系数的变化,否则会导致热防护失效,甚至产生反效果。      

Numerical investigation on flow and heat transfer characteristics of supercritical RP-3 in inclined pipe

Numerical simulations of flow and heat transfer to supercritical RP-3 through the inclined tubes have been performed using LS k–e model embedded in Fluent. The physical properties of RP-3 were obtained using the generalized corresponding state laws based on the fourcomponent surrogate model. Mass flow rate is 0.3 g/s, system pressure is 3 MPa, inlet temperature is 373 K. Inclination of the inclined pipe varied from -90° to 90°, with heat flux varied from 300 k W/m~2 to 400 kW/m~2. Comparison between the calculated result and the experimental data indicates the range of error reasonable. The results of ±45° show that temperature inhomogeneity in inclined pipe produce the secondary flow in its cross section due to the buoyancy force. Depending on the strength of the temperature inhomogeneity, there will be two different forms of secondary flow and both contribute to the convective heat transfer in the pipe. The secondary flow intensity decreases when the inhomogeneity alleviates and thermal acceleration will play a leading role. It will have a greater impact on the turbulent flow to affect the convective heat transfer in the pipe. When changing the inclination, it affects the magnitude of the buoyant component in flow direction. The angle increases, the buoyancy component decreases. And the peak temperature of wall dominated by the secondary flow will move forward and increase in height.     

基于通用无线电外设的北斗信号仿真系统

研究了基于通用软件无线电外设(USRP)的北斗信号仿真系统。给出了北斗卫星电文的生成方式,使用Matlab读取星历信息并定义编码产生北斗卫星信号,并利用USRP实现北斗卫星电文的调制发射,利用接收机对该信号进行捕获接收,并对信号附加的多普勒频移进行仿真。最后通过接收机对仿真系统产生的信号进行接收验证。通过此仿真系统可更直观地研究北斗卫星信号,对研究北斗卫星导航系统具有一定的参考意义。     

基于调平回路的LESO抗干扰方法研究

针对平台台体转位过程中方位角速度对水平通道调平回路的干扰问题,提出了惯导平台调平回路抗干扰方法.将线性扩张状态观测器(LESO)应用于调平回路中,对干扰进行估计并实时补偿.基于调平回路模型,对LESO进行设计及仿真分析.仿真结果表明,LESO能准确估计干扰且动态补偿效果好,较原系统具有更强的抑制干扰能力.     

轴流压气机吞水后的性能变化研究

为了探究航空发动机吸入雨水后压缩系统的特性变化,针对水滴进入压气机后的湿压缩过程展开研究。基于两相流动的基本原理构建了气液两相的传热传质模型和颗粒运动模型,采用一维逐级叠加的方法计算压气机各级性能,并利用Fortran程序对吞雨后压气机整体性能进行了计算。计算结果表明当吞雨量从3%增加到15%时,压气机压比的下降幅度分别由5.7%增加至15.7%;压气机各级温比的变化特性揭示了液滴在压气机前面级蒸发小、后面级蒸发大的规律;通过对比干、湿压缩条件下的压气机整体特性,可得出吞雨后压气机稳定工作范围变窄的结论。     

惯性器件精密零件微小毛刺去除技术研究

针对惯性器件中的外形复杂类零件、通孔交叉孔类零件、特殊材料类零件等微小毛刺去除需求,分析了现有控制工艺方法不足.通过开展高效率、高质量的零件毛刺去除试验,研究了磨粒流去毛刺、磁力研磨去毛刺、强力超声波去毛刺等精密去毛刺新方法对产品质量的影响,分析了先进去毛刺工艺方法的适用性,探索了惯性器件零件去毛刺技术发展方向.     

An experimental system for release simulation of internal stores in a supersonic wind tunnel

Aerodynamic parameters obtained from separation experiments of internal stores in a wind tunnel are significant in aircraft designs. Accurate wind tunnel tests can help to improve the release stability of the stores and in-flight safety of the aircrafts in supersonic environments.A simulative system for free drop experiments of internal stores based on a practical project is provided in this paper. The system contains a store release mechanism, a control system and an attitude measurement system. The release mechanism adopts a six-bar linkage driven by a cylinder, which ensures the release stability. The structure and initial aerodynamic parameters of the stores are also designed and adjusted. A high speed vision measurement system for high speed rolling targets is utilized to measure the pose parameters of the internal store models and an optimizing method for the coordinates of markers is presented based on a priori model. The experimental results show excellent repeatability of the system, and indicate that the position measurement precision is less than0.13 mm, and the attitude measurement precision for pitch and yaw angles is less than 0.126°, satisfying the requirements of practical wind tunnel tests. A separation experiment for the internal stores is also conducted in the FL-3 wind tunnel of China Aerodynamics Research Institute.     

电网电压不平衡及谐波畸变时基波电压正负序分量分离新方法

针对传统锁相环(PLL)在电网电压不平衡及谐波畸变下利用常规软件锁相环不能准确获取相位的问题,提出了一种新的正负序分量分离新方法。利用了相序解耦谐振控制器能去除高次谐波和延时信号消除(DSC)法可滤除特定谐波的特性,将相序解耦谐振和延时信号消除法结合起来,达到更好的正负序分量分离的效果。最后,采用MATLAB/Simulink软件仿真结果证明了所提出方法的可行性和有效性。     

固体火箭发动机零维两相燃烧室压强计算方法研究

为了更准确地预估含金属燃料固体火箭发动机的燃烧室压强,在压强计算中考虑两相流的影响,从一维两相喷管流动的求解出发,通过两相平衡流模型、两相常滞后模型、两相等温流模型、颗粒定温模型等模型的简化,分别推导不同模型下喷管中两相混合物的流量计算公式,再把流量公式应用到发动机零维内弹道理论中,推导并简化得到零维燃烧室平衡压强的计算公式。把压强公式用于HTPB推进剂固体火箭发动机和铝冰固体火箭发动机的燃烧室压强计算,结果表明,当固体推进剂中金属含量较高时(如铝含量为21%的HTPB推进剂发动机),用传统零维燃烧室压强公式预估的压强与实验误差较大,而使用合适的两相流模型和对应的零维燃烧室压强计算方法,在HTPB发动机中,能把压强预估结果与实验的误差降低到6%以内。如果使用多维内流场计算的方法,燃烧室压强预测结果的误差将下降到2.5%以内。结论发现在含金属固体火箭发动机的燃烧室压强计算中,考虑两相流的影响是必要的,而使用两相流修正后的零维燃烧室压强计算公式能够快速、较准确地预估这些发动机的燃烧室压强。