Si3 N4 粉体的分散及表面改性

研究了以聚丙烯酸铵为分散剂的Si3N4悬浮体的分散特性,以及酸洗和热氧化两种表面改性方法对Si3N4悬浮体的分散性和流变特性的影响.结果表明:分散剂聚丙烯酸铵的最佳酸碱环境为pH=9,最佳使用含量为0.2wt％,酸洗可有效去除粉料中的金属杂质,使Si3N4粉体在悬浮体中粒径分布更集中且粒径主峰值向小粒径移动,同时可使悬浮体的黏度降低.热氧化处理可大幅度降低Si3N4悬浮体的黏度,提高其流变特性.     

民用飞机后机身结构静力试验方案设计

针对某民用飞机后机身结构特点和受载形式,设计了相应的静力试验方案。该方案合理模拟了后机身结构的支持和边界条件,同时对后机身严重载荷情况进行分析处理,实现了飞行载荷和惯性载荷在后机身结构上的施加,顺利完成了大部段复杂结构的静强度试验。试验结果表明,后机身结构能够承受极限载荷,其刚度和强度满足设计要求。     

Adaptive path planning for unmanned aerial vehicles based on bi-level programming and variable planning time interval

This paper presents an adaptive path planner for unmanned aerial vehicles (UAVs) to adapt a real-time path search procedure to variations and fluctuations of UAVs’ relevant performances, with respect to sensory capability, maneuverability, and flight velocity limit. On the basis of a novel adaptability-involved problem statement, bi-level programming (BLP) and variable planning step techniques are introduced to model the necessary path planning components and then an adaptive path planner is developed for the purpose of adaptation and optimization. Additionally, both probabilistic-risk-based obstacle avoidance and performance limits are described as path search constraints to guarantee path safety and navigability. A discrete-search-based path planning solution, embedded with four optimization strategies, is especially designed for the planner to efficiently generate optimal flight paths in complex operational spaces, within which different surface-to-air missiles (SAMs) are deployed. Simulation results in challenging and stochastic scenarios firstly demonstrate the effectiveness and efficiency of the proposed planner, and then verify its great adaptability and relative stability when planning optimal paths for a UAV with changing or fluctuating performances.     

Relay selection based on MAP estimation for cooperative communication with outdated channel state information

In this paper, we consider an amplify-and-forward (AF) cooperative communication system when the channel state information (CSI) used in relay selection differs from that during data transmission, i.e., the CSI used in relay selection is outdated. The selected relay may not be actually the best for data transmission and the outage performance of the cooperative system will deteriorate. To improve its performance, we propose a relay selection strategy based on maximum a posteriori (MAP) estimation, where relay is selected based on predicted signal-to-noise ratio (SNR). To reduce the computation complexity, we approximate the a posteriori probability density of SNR and obtain a closed-form predicted SNR, and a relay selection strategy based on the approximate MAP estimation (RS-AMAP) is proposed. The simulation results show that this approximation leads to trivial performance loss from the perspective of outage probability. Compared with relay selection strategies given in the literature, the outage probability is reduced largely through RS-AMAP for medium-to-large transmitting powers and medium-to-high channel correlation coefficients.     

Environmental stress level evaluation approach based on physical model and interval grey association degree

 Associating environmental stresses (ESs) with built-in test (BIT) output is an important means to help diagnose intermittent faults (IFs). Aiming at low efficiency in association of traditional time stress measurement device (TSMD), an association model is built. Thereafter, a novel approach is given to evaluate the integrated environmental stress (IES) level. Firstly, the selection principle and approach of main environmental stresses (MESs) and key characteristic parameters (KCPs) are presented based on fault mode, mechanism, and ESs analysis (FMMEA). Secondly, reference stress events (RSEs) are constructed by dividing IES into three stress levels according to its impact on faults; and then the association model between integrated environmental stress event (IESE) and BIT output is built. Thirdly, an interval grey association approach to evaluate IES level is proposed due to the interval number of IES value. Consequently, the association output can be obtained as well. Finally, a case study is presented to demonstrate the proposed approach. Results show the proposed model and approach are effective and feasible. This approach can be used to guide ESs measure, record, and association. It is well suited for on-line assistant diagnosis of faults, especially IFs.     

Passive inter-modulation scattering analysis of reflector considering contact nonlinearity

 Passive inter-modulation (PIM) is a form of nonlinear distortion caused by the inherent nonlinearities of the passive devices and components in RF/microwave system. It will degenerate the performance of communication system with broad-band channel and high-sensitivity receiver. Therefore, it is necessary to construct a model to simulate this process in order to predict the level of PIM. This paper is aimed at constructing some plate models with one-dimensional and two-dimensional contact nonlinearity sections illuminated by two-tone waves, and calculating the scattered field at a fixed-point in space using time-domain physical optics method. By taking fast Fourier transform (FFT), we get the spectrum of the scattered field and then analyze the generated PIM products. At the end of this paper, some numerical examples are presented to show the influence rules of the relative factors on PIM. The results indicate the variation of the level of PIM with the number of the nonlinear regions, the nonlinear spacing, and the incident power levels.     

技术成熟度评价方法及其在交会对接任务中的应用

介绍了技术成熟度等级和评价的概念,简述了技术成熟度评价在国外航天工程中的应用情况,提出了航天工程技术成熟度评价标准,包括开展技术成熟度评价的目的、技术成熟度的详细定义及其内涵,并以技术成熟度等级五级为例,给出了具有可操作性的评价细则以及实施要点,通过交会对接任务中运载火箭评价应用实例对技术成熟度评价的应用进行了说明。     

大型客机后缘襟翼滑轨整流罩气动外形设计方法

大型客机后缘襟翼机构伸出机翼下表面会带来气动损失,必须设计相应整流罩。整流罩的外形尺寸对气动力影响较大,会直接影响飞机的气动特性。设计整流罩时应该遵循整流罩外形设计要求,使其引起的高速巡航阻力尽可能小。在查阅相关文献、对比研究大量整流罩图片、分析研究计算机辅助设计(CAD)中NURBS曲面曲线描述方法的基础上,建立了一套详细的大型客机后缘襟翼滑轨整流罩外形设计方法,该方法在满足整流罩包裹住机构、减小气动损失等基本要求的同时,缩短了整流罩设计周期。     

民用飞机应急处理分析流程研究

民用飞机在飞行过程中必然会遇到一些难以预料的情况,如何使空中和地面的工作人员能快速有效地处理飞机在飞行过程中出现的突发事件,已成为世界各国航空运输业关注的重点。为了在突发事件发生后能最大限度地保障乘客和飞机的安全,介绍了空乘及地面工作人员在突发事件发生后的应急处理流程。     

民用飞机最小离地速度试飞实施方法研究

对民用飞机最小离地速度( VMU )试飞实施方法进行了研究,主要包含了条款的理解、试验准备、试验分工、模拟器工作准备、试飞技术和数据处理等内容,为民用飞机最小离地速度试飞提供指导。同时作为国内新兴的职业---试飞工程师( FTE),也对其在试飞过程中的分工和职责进行了阐述。