Digital Aircraft Sheet Metal Part Manufacturing System and Its Key Technology

The architecture of digital sheet metal manufacturing system is proposed based on the classification of sheet metal manufacturing information.The essence of digital manufacturing is the definition,management and transfer of information,and the key technologies are brought forward and described.It is pointed out that knowledge-based manufacturing elements design is necessary to make digital technology efficient.The management of all kinds of sheet metal manufacturing element information is to build single source of manufacturing data.Multi-state model-based digital transfer and coordination method is designed to provide a foundation for digital manufacturing of aircraft sheet metal part.The application of digital sheet metal manufacturing is exemplified with an aircraft sheet metal part.The application result is compared to that of the traditional analog transfer technology.It is shown that the developed technology can improve part quality,shorten manufacturing time and lower manufacturing cost.     

Implementation of a novel matrix converter PMSM drive

This paper proposes a neural-network current-regulated switching strategy and an intelligent controller for a matrix converter permanent magnet synchronous motor (PMSM) drive system. By using this new switching strategy, the current harmonics of the system are effectively reduced. In addition, by using the intelligent controller, position control of the drive system can be achieved and an adjustable speed range from 1 r/min to 1500 r/min can be obtained. All the current-loop, speed-loop, and position-loop control algorithms are implemented by a 32-bit TMS320C40 digital signal processor. Several experimental results are shown to validate the theoretical analysis     

Power anomaly effects and costs in low-voltage mobile power systems

Electric power anomalies or disturbances can disrupt the normal operation of equipment, accelerate aging, or even cause outright failures thus resulting in increased costs of maintenance and reduced system reliability. Past research on the effects caused by power anomalies has been mostly focused on industrial, commercial, or residential systems, or on power distribution equipment. A literature survey reveals that there is no comprehensive review related to low-voltage (LV) power systems and utilization equipment applicable to military combat vehicles, such as aircraft and ships. This paper summarizes the results of a new literature survey that focused on the causes, effects, and mitigation methods for power anomalies typical of LV mobile power systems. Electric power anomaly cost data collected from the literature are also presented, from which the costs of anomalies to the national defense are estimated using some simple rationales.     

光学中心偏测量仪软件研制

文章介绍了北京空间机电研究所自行研制的光学中心偏测量仪的软件设计思路、工作原理 ,并对一些关键技术进行了讨论。     

EUROCAT－X系统故障的诊断和分析

NESACC项目是我国空管史上规模最大的空管建设项目。该项目总投资近20亿人民币,分别在北京、上海、广州兴建三大区域管制中心,使用Thales公司研制的欧洲猫(EUROCAT-X)空管自动化系统,配备先进的自动化设备,使空管工作更为科学、直观、安全。EUROCAT-X系统自运行以来,运行情况基     

如何做好雷达管制下航空器的飞行动态监控

一、前言在雷达管制空域,只要管制员发出“radar contact”或“radaridentified”这样的指令,就担负起了对该航空器的一切动态过程的监控责任。如果对该机的飞行动态监控不到位,造成的一切不安全后果,雷达管制员都将难辞其咎。近来在全国范围内发生的几起不安全事件,多是由于管     

加速器切线照相技术研究

根据工作实践研究了固体发动机切线照相无损检测中黑度分布、散射线防治、象质计使用、检测概率计算、脱粘临界值确定等技术问题.     

关于平面空穴流动的截断误差减小方法(英文)

提出了一种新的截断误差减小方法。该方法是利用在粗网格 ( 2 h)上估算截断误差进而减小在原始网格( h)上的误差的迭代过程 ,最终目的是利用粗网格得出更精确的结果以及发展一种新的粗网格直接数值模拟方法     

均布压力作用各向异性矩形薄板大挠度问题

基于冯·卡门模型，选择中心挠度为摄动参数，利用摄动方法将正交异性矩形薄板大挠问题的非线性偏微分方程组逐级线性化，导出了各级摄动对应的几个线性偏微分方程组，然后再借助变分法求解，得到了均布载荷作用下正交异性矩形薄板的载荷-挠度曲线。     

一个飞机结构优化设计软件

本文根据有限元分析基础,研究薄壁结构在应力、位移、最小尺寸约束下结构最轻重量的优化设计问题。用Kuhn-Tucker(库恩-塔克)必要条件将多个位移约束简化为单一位移约束(称为最临界位移约束),建立位移约束下的优化设计准则.从而避免大批拉格朗日乘子的计算,并结合满应力优化设计准则,形成了在有效约束界面逐步逼近最优设计点的方法——包络法。用某型飞机后机身一段优化设计作为本文的实际应用,得到令人满意的结果。