飞行控制律对体自由度颤振特性影响试验

飞翼飞机易发生刚体短周期模态与机翼低阶弯曲模态耦合所致的体自由度颤振。飞行控制系统对飞机的短周期模态特性影响很大,因此考虑飞行控制系统的闭环体自由度颤振特性值得进一步研究。针对自主设计的颤振模型开发了相应的俯仰姿态保持控制律,综合运用风洞试验和仿真计算开展了相关研究,获得了不同刚体自由边界条件下的开环/闭环体自由度颤振特性,研究了闭环增益对体自由度颤振特性的影响规律,简要分析了影响机理。试验和仿真计算结果共同表明：俯仰姿态保持控制律明显地改变了俯仰模态阻尼的原有走势,闭环后的体自由度颤振特性变化明显。以开环颤振速度为基准,采用较小的比例回路增益K_P或较大的微分回路增益K_D,飞行控制律能增加飞行器俯仰阻尼,提高体自由度颤振速度,反之飞行控制律将导致颤振速度降低。就本文控制律而言,当K_P<0.07或K_D>0.2时俯仰姿态保持控制律能起到抑制体自由度颤振的作用。     

机载液冷源系统热特性仿真实验研究

大功率的航空机载电子设备会存在超温问题,相比于风冷,采用液冷源对设备进行冷却具有更好的散热效果,因此需要对液冷源系统进行热特性仿真计算。以某型机载液冷源为例,建立其主要部件（包括储液箱、齿轮泵、散热器等）的传热理论数值计算模型,仿真分析-40~40 ℃温度工况下的系统热特性,并通过状态机编程实现超温情况下的温控仿真。结果表明：该型机载液冷源系统在典型工况下温度指标基本满足冷板进口温度（5~30 ℃）的技术指标要求;在系统温度上下偏值较大的情况下,采取提高风机转速或打开冲压空气口的控制方法,可明显改善该问题且冷板温度基本控制在 5~15 ℃范围内。     

可压缩多介质流动问题的高精度数值模拟方法

在可压缩流动问题的数值模拟领域,激波的高分辨率计算已取得重要进展.但是包含物质界面的可压缩多介质流动的数值模拟还存在诸多数值挑战,主要表现为界面处数值耗散过大和非物理振荡等问题.界面处流体性质的不连续性是造成可压缩多介质流动问题物理建模与数值方法困难的主要原因.为了建立一套高效的可压缩多介质流动问题的高精度数值模拟方案...     

铝合金回填式搅拌摩擦点焊工艺及组织特征分析

对2219+5A06铝合金进行了回填式搅拌摩擦点焊试验,研究了搅拌头旋转速度,下压-回抽速度和压入量等工艺参数对点焊接头力学性能的影响。对不同参数焊接的点焊接头进行了剪切拉伸抗力试验。结果表明：搅拌头旋转速度和下压-回抽速度对点焊接头的力学性能影响较大,而压入量对力学性能的影响较小。对点焊接头的微观组织分析表明,焊点接头可分为焊核区、竖直面热机影响区和水平面热机影响区三个部分。焊核区及水平面热机影响区为细小的等轴晶粒,水平面热机影响区形成与板材平行的结合面,竖直面热机影响区及焊点根部的hook缺陷是焊点力学性能的薄弱区域。     

热处理对高Co-Ni超高强度钢冲击断口的影响

研究了不同固溶及回火温度对高Co-Ni超高强度钢23Co 14Ni12Cr3Mo的Charpy V型缺口试样冲击功AKV和硬度HRC的影响,并用扫描电镜观察分析不同处理状态下的冲击断口形貌,用透射电镜对未溶碳化物进行了分析.结果表明,在850～930 ℃范围内固溶,随温度的提高,冲击功升高,硬度先升高后降低;在454～510 ℃范围内回火,随温度的提高,冲击功也增加,硬度降低.断口形貌观察结果表明,试验用钢冲击断口形貌均呈韧窝状,为韧性穿晶断裂,随固溶温度升高韧窝变大变深.韧窝中发现M23C6型碳化物颗粒,随固溶温度的升高而逐渐减少,提高固溶温度对改善试验用材料综合性能有利.     

Nonlinear Dynamics Behaviors of a Rotor Roller Bearing System with Radial Clearances and Waviness Considered

A rotor system supported by roller beatings displays very complicated nonlinear behaviors due to nonlinear Hertzian contact forces, radial clearances and bearing waviness. This paper presents nonlinear bearing forces of a roller bearing under four-dimensional loads and establishes 4-DOF dynamics equations of a rotor roller bearing system. The methods of Newmark-β and of Newton-Laphson are used to solve the nonlinear equations. The dynamics behaviors of a rigid rotor system are studied through the bifurcation, the Poincar è maps, the spectrum diagrams and the axis orbit of responses of the system. The results show that the system is liable to undergo instability caused by the quasi-periodic bifurcation, the periodic-doubling bifurcation and chaos routes as the rotational speed increases. Clearances, outer race waviness, inner race waviness, roller waviness, damping, radial forces and unbalanced forces-all these bring a significant influence to bear on the system stability. As the clearance increases, the dynamics behaviors become complicated with the number and the scale of instable regions becoming larger. The vibration frequencies induced by the roller bearing waviness and the orders of the waviness might cause severe vibrations. The system is able to eliminate non-periodic vibration by reasonable choice and optimization of the parameters.     

基于价值工程方法的武器装备价值分析

运用价值工程(VE)方法对武器装备进行了价值分析。给出了武器装备全寿命费用的分解结构和计算方法,同时分析了武器装备的效能结构并对其效能进行了量化。在此基础上建立了武器装备价值分析的理论及实践模型。     

D-最优试验设计在动力调谐陀螺测试中的应用

 为了提高动力调谐陀螺的静态漂移误差测试精度,针对简化静态漂移误差模型,并且考虑陀螺安装角误差的影响,依据D-最优试验设计理论以及正交设计的均匀分散性试验设计思路,设计了一种满足D-最优性质的正交八位置试验方案,并在整个正交空间内采用全局搜索的方法验证了其D-最优性。在相同试验环境下,采用力反馈位置试验法,以全正交空间预测误差平方和最小为评价准则,对该八位置试验方案和国军标GJB1183—91中的八位置试验方案进行比较与评价,试验结果表明该八位置试验方案优于国军标GJB1183—91中八位置试验方案。     

孔间距和前倾角对进出口扩张形气膜孔流量系数的影响(英文)

Discharge coefficients of 3-in-1 hole of three inclination angles and three spacing between holes are presented which described the discharge behavior of a row of holes. The inlet and outlet of the 3-in-1 hole both have a 15° lateral expansion. The flow conditions considered are mainstream turbulence intensities and density ratios of secondary flow to mainstream. The momentum flux ratios varied in the range from 1 to 4. The comparison is made of the discharge coefficients of three shaped holes to find an optimal hole with low flow loss. The results show that the discharge coefficients of 3-in- 1 hole are highest in three shaped holes and therefore this article is focused on the measurements of discharge coefficients of 3-in-1 hole for various geometries and aerodynamic parameters. The measured results of 3-in-1 hole indicate that turbulence intensities, density ratios and momentum flux ratios have weak influence on discharge coefficients for inclination angle of 20°. The high turbulence intensity yields the small discharge coefficients for inclination angle of 45° and 90°. The increased both momentum flux ratios and density ratios lead to the increased discharge coefficients for inclination angle of 45° and 90°. The increased inclination angle causes the rapidly increased discharge coefficients. There is a weak dependence of discharge coefficients on hole pitches.