全文获取类型
收费全文 | 2162篇 |
免费 | 594篇 |
国内免费 | 352篇 |
专业分类
航空 | 1832篇 |
航天技术 | 391篇 |
综合类 | 276篇 |
航天 | 609篇 |
出版年
2024年 | 26篇 |
2023年 | 44篇 |
2022年 | 126篇 |
2021年 | 136篇 |
2020年 | 128篇 |
2019年 | 102篇 |
2018年 | 106篇 |
2017年 | 130篇 |
2016年 | 89篇 |
2015年 | 134篇 |
2014年 | 117篇 |
2013年 | 161篇 |
2012年 | 183篇 |
2011年 | 181篇 |
2010年 | 194篇 |
2009年 | 167篇 |
2008年 | 151篇 |
2007年 | 176篇 |
2006年 | 156篇 |
2005年 | 128篇 |
2004年 | 101篇 |
2003年 | 69篇 |
2002年 | 67篇 |
2001年 | 53篇 |
2000年 | 37篇 |
1999年 | 35篇 |
1998年 | 29篇 |
1997年 | 18篇 |
1996年 | 10篇 |
1995年 | 6篇 |
1994年 | 5篇 |
1993年 | 15篇 |
1992年 | 5篇 |
1991年 | 5篇 |
1990年 | 4篇 |
1989年 | 4篇 |
1988年 | 2篇 |
1987年 | 4篇 |
1986年 | 2篇 |
1985年 | 2篇 |
排序方式: 共有3108条查询结果,搜索用时 115 毫秒
301.
为研究超高速碰撞过程中所产生碎片云的特性,在中国空气动力研究与发展中心超高速所碰撞靶上发展了四序列激光阴影照相系统.该系统由YAG激光光源、阴影仪、成像系统和控制系统组成,在采用多光源空间分离、偏振分光、光束角放大、补偿式滤光等技术后,获得了撞击速度v=4. 6km/s时碎片云的四序列阴影照片.笔者对该系统的工作原理、调试情况及试验结果进行了介绍.调试及试验结果表明:(1)该系统可以获得最小间隔为1μs、曝光时间为10ns的4个不同时刻的超高速碰撞碎片云图像,满足碰撞试验中对碎片云照相的要求;(2)该技术可以发展为更多序列激光阴影照相系统,并应用于其它超高速瞬态过程的测量显示. 相似文献
302.
303.
运用弹塑性有限元法,研究了胶粘剂弹性模量对含间隙的铝合金单搭接接头的影响。通过分析胶层和被粘物的应力分布,结果表明:间隙连接对接头端部的应力分布无明显影响,但对间隙附近的应力峰值影响较大;随着胶粘剂弹性模量的增大,间隙附近的应力峰值反而减小;对于高弹性模量胶粘剂接头,间隙对接头的应力峰值无明显影响,在不降低接头名义强度的基础上极大地提高了接头的实际强度;而对于低弹性模量胶粘剂接头,间隙使得接头的应力峰值明显上升,显著地降低了接头的名义强度和实际强度。数值模拟结果与已发表的试验数据大致吻合。 相似文献
304.
New Cutting Force Modeling Approach for Flat End Mill 总被引:1,自引:1,他引:0
WAN Min ZHANG Wei-hong TAN Gang QIN Guo-hua 《中国航空学报》2007,20(3):282-288
A new mechanistic cutting force model for flat end milling using the instantaneous cutting force coefficients is proposed. An in-depth analysis shows that the total cutting forces can be separated into two terms: a nominal component independent of the runout and a perturbation component induced by the runout. The instantaneous value of the nominal component is used to calibrate the cutting force coefficients. With the help of the perturbation component and the cutting force coefficients obtained above, the cutter runout is identified. Based on simulation and experimental results, the validity of the identification approach is demonstrated. The advantage of the proposed method lies in that the calibration performed with data of one cutting test under a specific regime can be applied for a great range of cutting conditions. 相似文献
305.
LUO Cheng LIU Hua YANG Jia-ling LIU Kai-xin 《中国航空学报》2007,20(3):230-235
Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks. 相似文献
306.
壁虎脚的粘着机理对航天机器人脚掌的研制和开发具有重要启发意义.通过单根刚毛与光滑表面黏着力模型与计算、卫星粗糙表面分布模型与接触概率与计算、刚毛阵列与卫星粗糙表面黏着力模型与计算等,分析仿壁虎刚毛阵列对卫星表面的吸附能力,发现在一定条件下仿壁虎刚毛阵能够在太空失重环境中黏着在卫星表面,对航天舱内爬行机器人、管道机器人的... 相似文献
307.
针对低轨(low earth orbit,LEO)Walker星座构型稳定性维持问题,分析了低轨卫星的轨道摄动和星座构型稳定性的影响因素.通过分析低轨Walker星座的轨道摄动和相对漂移特点,提出了两次偏置策略.首先,依据未偏置时星座相对漂移量拟合得出第一次偏置时的偏置量.然后利用第一次偏置后的相对漂移量拟合得出第二次... 相似文献
308.
309.
高轨卫星、深空探测器在工作周期内地影时间较短,储能电池长期处于搁置状态,而在存储过程中由于界面副反应的存在会导致持续的锂离子电池容量衰降,影响储能电池的使用寿命。通过dV/dQ曲线分析、交流阻抗分析和解剖分析发现在存储过程中活性Li损失是导致锂离子电池容量损失的主要原因,在100%SoC状态时还会导致电解液在负极表面的分解加剧,引起正极的界面膜阻抗R_(SEI)和颗粒间接触阻抗R_(CR)出现明显的增加。研究结果表明:深空探测器电源系统在存储期间为了减少过放电风险,并减少不可逆容量损失,应将蓄电池的荷电状态控制在20%SoC左右,并定期进行充电。 相似文献
310.
传感器安装对平板气动热测量精度的影响 总被引:1,自引:0,他引:1
对高超声速飞行器来说,气动热的准确预测是其合理选择防热材料及热结构设计的重要依据,但目前在激波风洞试验中气动热的高精度测量仍较为困难,热流的测量精度受到诸多非理想因素的影响,但传感器安装对热流测量精度的影响却鲜见研究。选取平板模型来研究传感器非理想安装对气动热测量精度的影响,针对不同的传感器安装偏差(凸出或凹入模型表面0.1~0.5 mm),分析不同雷诺数下传感器安装对气动热测量精度的影响规律及机理。研究结果表明:传感器安装对气动热测量精度有较大影响,凸出安装会导致热流测量结果偏大,而凹入安装则会导致测量结果偏小,热流偏差会随着安装偏差的增大而增大,且高来流雷诺数下传感器非理想安装所引起的热流误差更大;以边界层当地厚度对凹凸程度无量纲化,非理想安装带来的测量偏差只与该无量纲参数相关。研究结果能够为气动热测量的实验方案设计及测量误差分析提供一定的理论指导。 相似文献