煤油液滴高压蒸发特性

采用真实流体模型描述高压下流体热物理性质的非理想性,并采用状态方程（EoS）法计算多组分高压气-液相平衡及环境气体溶解性,在此基础上建立包含亚临界和超临界两种不同机制的瞬态液滴高压蒸发模型。针对中国新一代高压补燃液氧/煤油发动机,详细研究了煤油液滴在超临界环境下的高压蒸发特性及各因素影响机理。结果表明：高压环境会显著加快液滴温升速率,但弱超临界环境下仍然为相平衡控制的亚临界蒸发状态;只有强超临界环境下才较容易发生扩散控制的超临界蒸发状态。在高压、高温环境下,忽略气相溶解性将导致液滴蒸发速率明显偏小。针对弱超临界环境,温度升高会使液滴蒸发速率单调增加;压力升高则在低温下降低蒸发速率,而在高温下加快蒸发速率。针对强超临界环境,温度升高只提升初始亚临界蒸发阶段的蒸发速率,而超临界蒸发阶段的蒸发速率与环境温度无关;压力升高则同样会提升初始亚临界蒸发阶段的蒸发速率,但会降低超临界蒸发阶段的蒸发速率,此时的总蒸发寿命随压力升高小幅下降。     

压力振荡对气液同轴离心式喷嘴自激振荡的影响

为了研究供应系统振荡对气液同轴离心式喷嘴自激振荡的影响,采用水和空气作为模拟介质,开展了室压条件下冷态喷雾试验。通过试验分析了供应系统有/无振荡两种情况下离心式喷嘴的喷雾形态,以及供应系统有/无振荡两种情况下气液同轴离心式喷嘴自激振荡的喷雾形态。发现当离心式喷嘴供应系统振荡时,离心式喷嘴产生的锥形液膜也周期性地振荡,同时出现Klystron效应。液膜周期性振荡以及Klystron效应出现的频率与供应系统振荡频率一致。Klystron效应的出现使得喷雾锥角突然减小,锥形液膜发生折叠。供应系统振荡对自激振荡喷雾形态也有显著影响。供应系统振荡引起的Klystron效应使得液膜锥角减小,从而造成"圣诞树"型自激振荡喷雾上的"树枝"增多,同时自激振荡频率增加。这是因为当速度大的液膜追上速度小的液膜时,就会产生Klystron效应并使液膜速度增加。而液膜运动速度越大自激振荡频率也就越大。虽然在供应系统中施加激励没有发生"锁频"现象,但是自激振荡的强度在一定程度上减弱,并且伴随着自激振荡的"分频"现象,即自激振荡频率从一个主频向两侧分化为两个主频。     

一种低速风洞大流量进气道试验系统研制

为了提高FL-8风洞进气道试验能力,结合该风洞特点,在不破坏原有进气道试验系统前提下,研制了一路大流量进气道试验系统,采用直线形式布置在风洞中心,引射混合气体扩压减速后排入风洞扩散段内。该系统可实现进气道流场模拟、性能测量、流量控制与测量。为了验证该系统性能,在FL-8风洞进行试验验证了引射器的引射能力,排气对风洞流场的影响以及流量的控制与测量精度。该系统测量精度高,流量测量精度达到0.3%以上引射能力强,排气对风洞流场影响小,可模拟单路流量2.8kg/s,较原FL-8进气道试验能力提高50%以上,并且与原FL-8进气道试验系统结合使用,可实现三路进气道同时模拟。     

双馈异步风力发电机气隙偏心故障诊断研究现状与发展

双馈异步风力发电机(DFIG)机械故障在实际运行中尤其不可忽略,不论是转子刚度不足还是轴承磨损或安装误差,都会导致气隙偏心,严重时甚至会烧毁电机,因此对风机进行准确高效的气隙偏心故障诊断至关重要。简单介绍DFIG产生气隙偏心的故障机理,再对当前已有的相关故障诊断方法做重点归类阐述,最后展望未来的DFIG气隙偏心故障诊断方法的发展趋势和方向。     

Measurement of mass diffusion coefficients of O_2 in aviation fuel through digital holographic interferometry

The experimental apparatus to measure the mass diffusion coefficients of O2 in aviation fuel was constructed based on the digital holographic interferometry method. The theory of mass diffusion coefficient and interference image processing were introduced in detail. The accuracy of the experiment was verified by measuring the mass diffusion coefficient of 0.33 mol/L KCl in aqueous solution at 298.15 K. The mass diffusion coefficients of O_2 in RP3 and RP5 aviation fuels were measured at temperature from 278.15 K to 333.15 K, and the Arrhenius equation was employed to fit the experimental data. In terms of the Stokes-Einstein equation, the viscosities of these two aviation fuels were tested to estimate the correlation among mass diffusion coefficient, viscosity and temperature. A uniform polynomial calculation correlation was proposed to predict the mass diffusion coefficients of O_2 in both RP3 and RP5 aviation fuels, and its accuracy is considerably higher than that of the Stokes-Einstein equation.     

Assessment on critical technologies for conceptual design of blended-wing-body civil aircraft

Civil aviation faces great challenges because of its robust projected future growth and potential adverse environmental effects. The classical Tube-And-Wing(TAW) configuration following the Cayley's design principles has been optimized to the architecture's limit, which can hardly satisfy the further requirements on green aviation. By past decades' investigations the BlendedWing-Body(BWB) concept has emerged as a potential solution, which can simultaneously fulfill metrics of noise, emission and fuel burn. The purpose of the present work is to analyze the developments of critical technologies for BWB conceptual design from a historical perspective of technology progress. It was found that the high aerodynamic efficiency of BWB aircraft can be well scaled by the mean aerodynamic chord and wetted aspect ratio, and should be realized with the trade-offs among stability and control and low-speed performance. The structure concepts of non-cylinder pressurized cabin are of high risks on weight prediction and weight penalty. A static stability criterion is recommended and further clear and adequate criteria are required by the evaluations of flying and handling qualities. The difficulties of propulsion and airframe integration are analyzed. The energy to revenue work ratios of well-developed BWB configurations are compared,which are 31.5% and 40% better than that of TAW, using state-of-art engine technology and future engine technology, respectively. Finally, further study aspects are advocated.     

Numerical investigation on flow and heat transfer characteristics of supercritical RP-3 in inclined pipe

Numerical simulations of flow and heat transfer to supercritical RP-3 through the inclined tubes have been performed using LS k–e model embedded in Fluent. The physical properties of RP-3 were obtained using the generalized corresponding state laws based on the fourcomponent surrogate model. Mass flow rate is 0.3 g/s, system pressure is 3 MPa, inlet temperature is 373 K. Inclination of the inclined pipe varied from -90° to 90°, with heat flux varied from 300 k W/m~2 to 400 kW/m~2. Comparison between the calculated result and the experimental data indicates the range of error reasonable. The results of ±45° show that temperature inhomogeneity in inclined pipe produce the secondary flow in its cross section due to the buoyancy force. Depending on the strength of the temperature inhomogeneity, there will be two different forms of secondary flow and both contribute to the convective heat transfer in the pipe. The secondary flow intensity decreases when the inhomogeneity alleviates and thermal acceleration will play a leading role. It will have a greater impact on the turbulent flow to affect the convective heat transfer in the pipe. When changing the inclination, it affects the magnitude of the buoyant component in flow direction. The angle increases, the buoyancy component decreases. And the peak temperature of wall dominated by the secondary flow will move forward and increase in height.     

涡桨飞机螺旋桨滑流气动干扰效应及流动机理

螺旋桨滑流对飞机各气动部件的干扰是涡桨飞机气动设计中面临的难点之一。以某双发涡桨支线客机为对象,采用数值模拟手段分析了滑流对机翼、平尾、垂尾的影响及其流动机理。计算采用基于动态面搭接网格技术的非定常方法,气动力与表面压力分布的计算结果均与实验值吻合良好。研究结果表明：在滑流影响下,全机升力和阻力有所增加,升阻比和纵向静稳定度有所降低,并在无侧滑状态下产生了滚转力矩和偏航力矩;在不同展向位置,滑流对机翼表面流动分离的影响存在显著的差异。在螺旋桨下行运动一侧,滑流的旋转减小了当地迎角,同时桨后气流速度较高,翼面流动分离被有效抑制。在螺旋桨上行运动一侧,滑流的旋转增大了当地迎角,而且桨后气流速度较低,因而翼面流动分离并未得到明显改善;在中小迎角下,滑流对背景飞机平尾当地的动压没有产生影响,但增加了下洗角变化率,进而导致平尾效率降低;垂尾的侧力与偏航力矩是由滑流的侧洗引起的,而滑流的侧洗又与左右两侧机翼升力分布的不对称性有关。     

基于动力学边界的结冰飞机安全预警方法

结冰严重破坏飞机的动力学特性,使飞机的非线性和动力学耦合特性表现明显,导致传统的安全预警方法无法准确有效地评估飞行存在的潜在风险,易引发飞行事故。为解决此问题,提出了一种基于动力学边界的新型安全预警方法,该方法可综合考虑飞机的动力学耦合特性,可为结冰飞机的实时安全预警系统的构建提供有力的理论支撑。首先,基于微分流形理论确定结冰飞机精确的动力学边界,并详细分析了飞机结冰对动力学边界的影响;其次,利用动力学边界相对距离对飞行风险进行量化,结合动力学边界的特性确定了安全预警的方法;最后,搭建了飞行仿真训练系统,并以着陆为训练科目,通过与传统迎角安全预警方法对比,得到基于动力学边界安全预警方法的优越性。研究结果表明,相比于传统迎角限制方法,动力学边界安全预警方法可提前发现飞行中存在的潜在风险,且基于此方法的飞行训练系统可对驾驶员进行结冰安全操纵训练可提高结冰飞机的飞行安全。     

常规闭口风洞相阵列气动声学试验

传统气动声学研究观点认为,精确的声学测量要求风洞背景噪声和洞壁反射足够低,传声器测量结果有足够高的信噪比,这是大多数风洞无法达到的要求.近些年,基于声纳和雷达技术发展起来的麦克风相阵列技术可以通过增加阵列的传声器数目从而大幅提高声学测量的信噪比,具有噪声源研究和定位能力,并被成功地应用于非声学固壁风洞噪声源测量和噪声物理机制研究.作者基于相阵列波束生成频域算法研制出常规闭口风洞相阵列系统及相关技术,在FD-09风洞尝试进行了相阵列校准试验和某民机噪声测量试验.结果表明:相阵列技术能够准确捕捉到真实的校准声源,并从技术上验证了相阵列系统在常规闭口风洞测量气动噪声是有效的.