Solar UV irradiance variation during cycles 22 and 23

The Solar Ultraviolet Spectral Irradiance Monitor (SUSIM) aboard the Upper Atmosphere Research Satellite (UARS) has been measuring solar UV irradiances since October 1991, a period which includes the decline of solar cycle 22 followed by the rise of cycle 23. Daily solar measurements include scans over the wavelength range 115–410 nm at 1.1 nm resolution. As expected, the measured time series of UV irradiances exhibit strong periodicities in solar cycle and solar rotation. For all wavelengths, the UV irradiance time series are similar to that of the Mg II core-to-wing ratio. During solar cycle 22, the irradiance of the strong Ly- line varied by more than a factor of two. The peak-to-peak irradiance variation declined with increasing wavelength, reaching 10% just below the Al edge at 208 nm. Between the Al edge and 250 nm the variation was 6–7%. Above 250 nm, the variation declines further until none is observed above 290 nm. Preliminary results for the first portion of cycle 23 indicate that the far UV below the Al edge is rising at about the same rate as the Mg II index while the irradiances in the Ly- emission line and for wavelengths longer than the Al edge are rising more slowly — even after accounting for the lower level of activity of cycle 23.     

Design and characteristics of a multiband communication satelliteantenna system

Feasibility studies on a multiband communication satellite antenna system and the key technologies involved in devising this system are described. The proposed multiband communication satellite utilizes four frequency bands: Ka (30/20 GHz), Ku (14/12 GHz), C (6/4 GHz), and S (2.6/2.5 GHz). It has six beam configurations, three multibeam and three shaped-beam. The following key technologies are presented: (1) a low-loss frequency selective subreflector (FSR) for compact feeds, (2) a low-loss and broadband frequency selective surface (FSS), and (3) a highly accurate and reliable mesh reflector     

High-Speed Homopolar Inductor Alternators of Minimum Leakage Reactance

The leakage reactance of the machine is expressed as an equation involving slot leakage, end-connection leakage, differential leakage, stator-halves leakage, and tooth-top leakage reactance. This leakage reactance equation, or objective function, is then minimized under suitable constraints. Geometric programming is used to carry through the optimization procedure. A computer program is developed and applied to find the optimum leakage reactance for a 95 kVA, 208 V, wye-connected, 40 800 r/min aerospace alternator, using 8-, 10-, and 12-pole machines.     

Attitude Determination Via Nonlinear Filtering

The theory of nonlinear filtering has been applied to the problem of the attitude determination of a satellite. Two approximation methods have been studied with a view to practical implementation. Computer simulation results are included.     

Aerodynamic Design Method of Integrated Aircraft with Submerged Intake Devices and Power Plant Included into Airframe Carrying System

This paper presents a theoretically and practically grounded architecture of design methods combination. A possibility and completeness of developing integral design solutions and intensifying the design process are provided by redistribution of emphases of numerical and natural experiments.     

The Electric Antennas for the STEREO/WAVES Experiment

The STEREO/WAVES experiment is designed to measure the electric component of radio emission from interplanetary radio bursts and in situ plasma waves and fluctuations in the solar wind. Interplanetary radio bursts are generated from electron beams at interplanetary shocks and solar flares and are observed from near the Sun to 1 AU, corresponding to frequencies of approximately 16 MHz to 10 kHz. In situ plasma waves occur in a range of wavelengths larger than the Debye length in the solar wind plasma λ _D ≈10 m and appear Doppler-shifted into the frequency regime down to a fraction of a Hertz. These phenomena are measured by STEREO/WAVES with a set of three orthogonal electric monopole antennas. This paper describes the electrical and mechanical design of the antenna system and discusses efforts to model the antenna pattern and response and methods for in-flight calibration.     

Notes on SCPC-FM System Design and Performance

In many domestic satellite communication systems single-channel per-carrier FM (SCPC-FM) has become the accepted transmission method for thin route communication. The SCPC-FM modem operates over a wide range of carrier frequencies and is designed to use satellite power and bandwidth efficiently. It incorporates elements which make the signal transfer complex, so the system behavior is not immediately obvious. This article investigates the signal processes and analyzes the performance of a companded and preemphasized SCPC-FM system and it furnishes insight into the choice of crucial system parameters.     

风洞模拟建筑物对大气污染物扩散影响的若干问题讨论

通过相似性分析,得到了大气污染建筑物影响风洞试验应满足的基本相似条件.由一个实例研究了利用常规风洞模拟装置和测试仪器进行大气污染建筑物影响风洞试验在技术上的可行性.结果显示:由于模拟装置和仪器条件的限制,在大多数风洞试验中存在大气边界层不完全模拟和仪器响应过慢等问题,但通过合理模拟来流的主要湍流特征和改进采样方法,可以在风洞中较真实地模拟建筑物对大气扩散的影响.     

Automated air defense system using knowledge-based system

The proposed KAAD (knowledge-based automated air defense) system demonstrates a man-machine environment for airspace defense systems. When the unknown aircraft is hostile, a threat rating and response methods are generated by the system. It serves as a double-check decision-making system for a war control center. In addition to this application, the KAAD system can also be a useful tool as a training program for the war controller. The capabilities of the system are limited due to the shortage of knowledge resources. It requires communications among war controllers and air fighter pilots to organize a practical knowledge base. It is shown that the KAAD system can be combined with an automated ATC (air traffic control) system to become a practical system for air defense applications     

Optimum gain control for A/D conversion using digitized I/Q data inquadrature sampling

Calculation of optimum gain for minimum distortion due to A/D (analog-to-digital) conversion requires the estimation of the input signal strength. To use a common AGC (automatic gain control) for both the I/Q (in-phase and quadrature) signals, it is efficient to estimate the input signal strength using the quantized A/D output from both channels. Assuming a Gaussian input, the relationship between σ of the input of the A/D converter and E(|x|+|y|) and E(max(|x|,|y|)+1/2 min (|x|,|y|)) for t quantized I/Q output x and y is derived. Numerical results obtained using the derived expression and the statistical data obtained through simulation show excellent agreement. It is concluded that, because of its simplicity, the cubic equation obtained by fitting the numerical results should be useful