利用地磁场给飞轮卸载的新方法

通过对圆轨道地磁场强度的变化规律分析 ,将卫星磁力矩器产生的磁矩按傅立叶级数展开 ,根据卫星所需卸载角动量大小 ,按照最优控制理论求出三轴磁矩取值 ,得出飞轮卸载控制律。最后文章给出飞轮卸载稳定性分析和仿真结果 ,表明这种飞轮卸载方法简单而且省能量。     

海洋监视卫星无源被动定位精度分析

分析了利用三星编队卫星对海上目标进行无源侦察、监视的原理,建立了利用时差定位法进行定位的精度模型,在此基础上推导了卫星对目标的定位精度与卫星编队构型、轨道高度、与目标的相对位置及卫星定轨精度和测量误差的关系。对模型进行了仿真计算和分析,仿真结果表明:合理增加卫星间的基线长度,保持卫星编队构型及其与目标间相对位置的均匀性可以有效提高卫星对目标的定位精度。     

分布式卫星精确构形保持变结构控制

分布式卫星构形精确保持是实现分布式卫星任务的关键技术。在控制模型不精确和摄动力不确定的条件下,经典控制方法在鲁棒性、动态品质和静态指标的权衡等方面存在不足。本文利用变结构控制方法,设计了分布式卫星精确构形保持的控制器,使控制方法对摄动干扰、模型不确定等具有鲁棒性,因而使构形保持方法在参考轨道存在小偏心率、摄动力存在等非理想情况下仍然可以正常进行。利用高精度动力学仿真环境,对方法的先进性进行了检验。     

重力梯度稳定小卫星的最优主动磁控和动量轮控制

为了提高小卫星定点精度,姿态控制系统采用俯仰轴动量轮控制和三轴磁力矩控制。用四元数方法建立起卫星动力学方程和运动学方程。以响应时间和响应时间内欧拉角误差和角速率误差的平方和这两个单目标作为目标函数,以三轴的位置增益、速率增益和卸载增益为设计变量,以三轴欧极子矩不超过要求值,俯仰轴的轮动量矩不超过要求值,以及末尾响应时间内应保证欧拉角和角速率逼近控制值为约束条件,建立起卫星最优控制模型。最后,作为例子应用到小卫星姿态控制中,结果证实最优控制算法是可行有效的。与传统PD控制相比,优化后的姿态控制性能也大大提高。     

模糊评价法在分散实习成绩评定中的应用

分散实习中，当某些学生工地偏远，指导老师监管困难时，其成绩评定只能依赖实习成果成绩与答辩成绩，这是一个多因素综合评价问题，采用模糊评价法能避免评价过程中主观性因素对结果的影响，研究提出了分散实习模糊评价体系，给出了综合评判义性失效时的解决办法，讨论了模糊评价方法的可行性。     

SOI工艺抗辐照SRAM型FPGA设计与实现

为提升SRAM型FPGA电路块存储器和配置存储器抗单粒子翻转性能，本文提出一种脉冲屏蔽SRAM单元结构。该结构通过在标准的六管单元中加入延迟结构,增大单元对单粒子事件响应时间，实现对粒子入射产生的脉冲电流屏蔽作用。以64k SRAM作为验证电路进行单粒子翻转性能对比，电路的抗单粒子翻转阈值由采用标准六管单元的抗单粒子翻转阈值大于25 MeV·cm 2·mg -1 提升至大于45 MeV·cm 2·mg -1 ，加固单元面积较标准六管单元增大约21.3%。30万门级抗辐照FPGA电路通过脉冲屏蔽单元结合抗辐照SOI工艺实现，其抗辐照指标分别为：抗单粒子翻转阈值大于37.3 MeV·cm 2·mg -1 ，抗单粒子锁定阈值大于99.8 MeV·cm 2·mg -1 ，抗电离总剂量能力大于200 krad(Si)。     

基于修正面元法的机翼焦点位置变化研究

针对静气动弹性问题中机翼焦点位置求解精度与效率的矛盾,提出采用分段斜率修正面元法来计算气动力,该方法以刚体机翼在不同迎角下的CFD数据作为修正基础,对弹性变形后的机翼下洗采用分段修正,克服了传统面元法无法考虑非线性因素的缺点。通过M6机翼气动焦点位置的计算表明:相对于CFD方法,该方法保持了较高的准确度并且计算效率较高;相对于传统面元法,该方法能够准确地计算焦点位置和弹性机翼焦点位置变化量,适用于工程设计。     

Robust control for constant thrust rendezvous under thrust failure

A robust constant thrust rendezvous approach under thrust failure is proposed based on the relative motion dynamic model. Firstly, the design problem is cast into a convex optimization problem by introducing a Lyapunov function subject to linear matrix inequalities. Secondly, the robust controllers satisfying the requirements can be designed by solving this optimization problem.Then, a new algorithm of constant thrust fitting is proposed through the impulse compensation and the fuel consumption under the theoretical continuous thrust and the actual constant thrust is calculated and compared by using the method proposed in this paper. Finally, the proposed method having the advantage of saving fuel is proved and the actual constant thrust switch control laws are obtained through the isochronous interpolation method, meanwhile, an illustrative example is provided to show the effectiveness of the proposed control design method.     

Study of amplification coefficient in a water-cooling Gardon-type heat power measuring apparatus

A new water-cooling Gardon-type heat power measuring apparatus is designed to meet the need of heat power source management and distribution. The steady state measurement mathematic model of the apparatus is built up in theory and the system amplification coefficient is defined as the ratio of the heat power to the temperature difference of the device, with which the value of the measured source power can be calculated easily with the corresponding temperature difference. In order to obtain an optimal heat power measuring system, the coefficients that can influence the relationship between the amplification coefficient, the temperature difference, and the heat power are analyzed. On the basis of these analyses, a set of experimental device is constructed and a number of experiments are carried on. Compared with the input heat power sample data, the error of the experimental measuring results is less than ±2%, and the experimental measuring values are in good agreement with the calculated theoretical ones. The heat power measuring apparatus can be applied in heat flux or heat power measurement in other fields due to its simple structure and high accuracy.