Influence of TiB2 particles on machinability and machining parameter optimization of TiB2/Al MMCs

In situ formed TiB₂ particle reinforced aluminum matrix composites (TiB₂/Al MMCs) have some extraordinary properties which make them be a promising material for high performance aero-engine blade. Due to the influence of TiB₂ particles, the machinability is still a problem which restricts the application of TiB₂/Al MMCs. In order to meet the industrial requirements, the influence of TiB₂ particles on the machinability of TiB₂/Al MMCs was investigated experimentally. Moreover, the optimal machining conditions for this kind of MMCs were investigated in this study. The major conclusions are: (1) the machining force of TiB₂/Al MMCs is bigger than that of non-reinforced alloy and mainly controlled by feed rate; (2) the residual stress of TiB₂/Al MMCs is compressive while that of non-reinforced alloy is nearly neutral; (3) the surface roughness of TiB₂/Al MMCs is smaller than that of non-reinforced alloy under the same cutting speed, but reverse result was observed when the feed rate increased; (4) a multi-objective optimization model for surface roughness and material removal rate (MRR) was established, and a set of optimal parameter combinations of the machining was obtained. The results show a great difference from SiC particle reinforced MMCs and provide a useful guide for a better control of machining process of this material.     

试飞员能力模型研究

在飞行器研制和人类飞行探索中,试飞员的能力至关重要。针对以往对试飞员能力的评价基本停留在"客观、正确、诚信、能力以及尊重他人"等主观、感性层面,分析了试飞员在飞行器研制试验与鉴定中的作用和任务,给出了试飞员能力模型和"百分制"对试飞员的计划、飞行、评价、报告和建议等基本能力的量化分配。将试飞员能力显性化,有利于试飞员能力的客观评价。     

数字全息测量超高速撞击碎片云实验研究

在中国空气动力研究与发展中心(CARDC)超高速碰撞中心(HIRC)7.6 mm超高速碰撞设备的基础上，搭建纳秒级脉冲激光数字全息系统。提出滤波片和衰减片组合布置，减弱超高速碰撞等离子体自发光、提高信噪比的方法。实验获得了2.25 mm铝球弹丸以4.0 km/s的速度撞击0.5 mm厚铝板形成碎片云的全息图。采用小波变换算法对碎片云全息图进行重建，得到超高速撞击碎片云的三维结构和碎片大小。碎片云的轮廓呈椭球型，分为碎片云的前端、核心和外壳，碎片主要分布在弹丸破碎形成的碎片云核心，存在大碎片，且分布较集中，对后板的损伤也严重     

基于LMS Virtual. Lab的系留气球仿真与优化

系留气球在近地面收放过程中存在俯仰角过大的问题，为了更全面地了解收放过程中不同因素对球体俯仰角的影响，采用LMS Virtua1. Lab建立了带滑轮索具系统的系留气球三维动力学模型进行仿真分析，结果表明，仿真结果与理论计算、测量数据都有较高的符合度。进而运用试验设计( DOE)方法，探索典型风速下球体俯仰角的响应区间。最后基于响应面模型的优化技术，对滑轮索具系统设计进行优化，有效改善了球体在收放过程中俯仰角过大的问题。仿真模型对系留气球系统设计及收放控制有一定的指导作用。     

黄渤海晴空像元下雾霾识别的机器学习算法

为实时有效地识别和监测雾霾，选取2013年10月4日与10月5日的两景MODIS遥感图像，利用不同类型像元的光谱差异，基于神经网络模型，建立海上雾霾的遥感识别机器学习算法。经检验表明，在晴空条件下，机器学习算法反演精度相对较高，已超过98%，利用算法可以实现对中国近海上空雾霾的监测。     

基于ANSYS Workbench的行星滚柱丝杠动态特性分析

通过Pro/Engineer建立行星滚柱丝杠三维模型，基于ANSYS Workbench有限元分析技术进行模态与谐响应分析，得到前六阶固有频率与各阶模态振型，确定共振频率，掌握对应频率下的位移峰值响应，并研究螺母处于不同工作位置时对固有频率的影响，为基于行星滚柱丝杠传动的舵系统抗振设计提供数据支撑。     

EPDM包覆层热解状态下的力学行为及本构模型

为了准确描述固体火箭发动机三元乙丙(EPDM)包覆层在不同热解状态下的力学特性,通过热重分析的方法得到EPDM的热解温度范围,并采用准静态单轴拉伸实验的方法获得EPDM在不同热解温度下的应力-应变曲线。以Ogden(n=2)模型为基础,分别对不同热解状态下的力学曲线进行建模,并通过对实验数据的拟合获得模型参数。结果表明,在初始热解状态下,材料只发生了少量的失水和气体的逃逸,其力学行为可通过粘超弹本构模型进行描述;随着材料热解程度增加,基体材料和填充纤维均遭到破坏,其力学行为表现为超弹脆性材料特性。     

基于改进WKNN的位置指纹室内定位算法

位置指纹算法是目前解决室内定位问题的主要方法,指纹特征和匹配算法为影响算法精度的两大因素.针对室内复杂环境下Wi-Fi信号强度波动较大的现象,提出了基于方差的加权距离以改进WKNN算法.在离线特征提取阶段,选择了均值和方差两个特征值,既反映该采样点的RSS幅值,也反映该点RSS的波动情况;在线阶段,根据方差提出了加权距离进行相似度的计算,查找距离最近的K近邻点,并以实际环境下采集的数据验证了改进WKNN算法在RSS波动大的情况下对定位效果的改善,在综合考虑了AP组合的影响后,实现了误差均值为1.456m的定位效果.     

基于层次评估理论的弹道导弹末段突防制导律研究

针对弹道导弹末段突防问题,应用层次性能评估体系,对弹道导弹末段典型突防制导律进行对比分析.并通过对弹道导弹制导精度、弹道导弹最大过载、弹道飞行时间和反导导弹脱靶量以及它们的均值、均方差的重要性和需求性分析,合理设置评估体系的指标及其权值,应用随机仿真分析方法,对比仿真经典比例导引、修正比例导引和变结构比例导引三种突防制导律的性能.仿真结果证明,层次评估理论可以用于弹道导弹末段突防制导律的评估及优选.     

New constitutive relation for eddy viscosity models

A new turbulent constitutive relation was directly derived from Boussinesq's hypothesis and mixing length theory, and then implemented in the standard k-ε model. The performance of this constitutive relation was validated in zero pressure gradient flat-plate boundary layer flow, fully-developed turbulent channel flow and separated flow in a plane asymmetric diffuser. The investigation demonstrated that, this new constitutive relation gave very accurate results in the former two basic cases and provided significant improvement in prediction of separated and reattachment points in the plane asymmetric diffuser. Separation and reattachment points at x/H=7.5 and 29 were calculated accurately in comparison to experimental results, and the static pressure coefficient of 0.82 was very close to large eddy simulation calculation. These results are very encouraging but further verification and extensive application of the new constitutive relation to other two-equation eddy viscosity model are needed.