全文获取类型
收费全文 | 677篇 |
免费 | 267篇 |
国内免费 | 99篇 |
专业分类
航空 | 634篇 |
航天技术 | 131篇 |
综合类 | 43篇 |
航天 | 235篇 |
出版年
2024年 | 6篇 |
2023年 | 27篇 |
2022年 | 55篇 |
2021年 | 53篇 |
2020年 | 52篇 |
2019年 | 42篇 |
2018年 | 44篇 |
2017年 | 55篇 |
2016年 | 51篇 |
2015年 | 57篇 |
2014年 | 52篇 |
2013年 | 49篇 |
2012年 | 54篇 |
2011年 | 69篇 |
2010年 | 46篇 |
2009年 | 43篇 |
2008年 | 52篇 |
2007年 | 62篇 |
2006年 | 44篇 |
2005年 | 29篇 |
2004年 | 20篇 |
2003年 | 23篇 |
2002年 | 23篇 |
2001年 | 16篇 |
2000年 | 11篇 |
1999年 | 8篇 |
排序方式: 共有1043条查询结果,搜索用时 31 毫秒
921.
922.
JIA Ming YANG Gongliu School of Instrumentation Science Opto-electronics Engineering Beihang University Beijing China 《中国航空学报》2011,24(5):640-647
Optical fiber coil winding model is used to guide proper and high precision coil winding for fiber optic gyroscope (FOG) application. Based on the large-deformation theory of elasticity, stress analysis of optical fiber free end has been made and balance equation of infinitesimal fiber is deduced, then deformation equation is derived by substituting terminal conditions. On condition that only axial tensile force exists, approximate curve equation has been built in small angle deformation scope. The comparison of tangent point longitudinal coordinate result between theory and approximation gives constant of integration, and expression with tangent point as origin of coordinate is readjusted. Analyzing the winding parameters of an example, it is clear that the horizontal distance from the highest point of wheel to fiber tangent point has millimeter order of magnitude and significant difference with fiber tension variation, and maintains invariant when wheel radius changes. The height of tension and accurate position of tangent point are defined for proper fiber guide. For application to fiber optic gyroscope, spiral-disc winding method and nonideal deformation of straddle section are analyzed, and then spiral-disc quadrupole pattern winding method has been introduced and realized by winding system. The winding results approve that the winding model is applicable. 相似文献
923.
924.
针对Kevlar层合板在超高速撞击条件下的力学特性的复杂性及参数不准确对数值仿真的不利影响,提出一种使用正交各向异性本构模型,Chang-Chang复合材料失效模型和有限元方法对Kevlar层合板的超高速撞击力学特性进行建模并运用连续响应面技术对材料失效模型参数进行识别的方法.然后使用该方法建立了与现有文献中的试验工况相对应的数值模型,并把Kevlar层合板材料失效模型的4个参数作为优化变量,以仿真结果与试验结果的二乘残差最小作为优化目标,使用连续响应面技术建立参数优化模型,由此识别这些参数.结果表明,该建模方法能正确描述Kevlar层合板的超高速撞击力学特性,采用识别后的参数进行仿真计算可以显著提高数值模型的仿真精度. 相似文献
925.
为了满足TBCC超级燃烧室的各工作模式下的低阻高效混合,设计了两种采用方形波瓣混合器和结构可调的导流片相结合的强化掺混方案。方案A由上下扩张角不等的波瓣混合器和处于波谷上方的离散状导流片组成,波瓣混合器正对于分流环;方案B由全环形导流片和上下等扩张角的波瓣混合器组成,波瓣混合器的中径小于分流环直径。通过数值研究对比分析了两种混合方案的流动特征发现,两种方案都未出现倒流和流动分离现象;除冲压模态时的波峰截面方案B的流线分布较为理想外,其它工作状态下方案A波峰和波谷截面流线分布均优越方案B。通过对总压恢复系数、热混合效率及动量混合系数的对比发现,混合方案A在飞行Ma03的各工作状态下的总压恢复系数均高于方案B最多高3.5%且能在较短的掺混距离内使内外涵气流的温度和速度混合均匀。考虑到兼顾飞行Ma03范围内的低阻高效混合要求,方案A具有良好的强化掺混特性。 相似文献
926.
针对一种以方形硅膜片为一次敏感元件、硅梁谐振子为二次敏感元件 ;采用电阻热激励、压敏电阻拾振的压力微传感器 ,分析了其工作机理 ;依幅值、相位条件讨论了该谐振式微传感器的闭环自激系统 ;建立了微传感器的温度场模型和热应力模型 ,并进行了仿真计算与分析 相似文献
927.
焊接构件低温疲劳P-S-N曲线的研究 总被引:3,自引:0,他引:3
焊接构件的低温 P-S-N曲线是冬季构件抗疲劳设计的基础.在PLG-300 kN高频疲劳试验机上,测定了在-25℃环境下4种应力水平对应的焊接构件的疲劳寿命,并得出了其中值S-N曲线.采用小样本实验的单侧容限分析方法,利用对数疲劳寿命变异系数的经验取值,得出了焊接构件的低温P-S-N曲线.这种方法既简便又经济,但需要由进一步的实验来完善. 相似文献
928.
929.
介绍了相移调制全桥ZVS-PWM拓扑的工作原理,分析了零电压开关的条件,给出了关键参数的计算公式,讨论了优缺点. 相似文献
930.