基于单应性矩阵的模型迎角单目视频测量方法

风洞试验中模型迎角的精准测量是降低阻力系数误差的重要途径之一,为此,提出了基于单应性矩阵的模型迎角单目视频测量方法。该方法通过两个单应性矩阵,获取试验过程中相机实时位姿和标记点物方空间位置坐标,应用坐标旋转关系,完成试验模型的迎角测量。数值仿真试验结果表明：迎角测量误差与待测标记点到风洞壁板间的距离偏差近似为线性关系,因此,当标记点不满足共面条件时,可根据该特点进行测量误差修正。静态标定和风洞迎角测量试验结果表明：修正系统误差后,迎角实测数据的测量准度在0.01°以内,精度不超过0.012°。本文方法易于实施,工程实用价值强。     

超高速干气密封扰流效应及抑扰机制

干气密封在高速时优异的动压性能使其应用范围从传统的压缩机、离心机等中高速设备逐渐扩大到航空发动机、（微型）燃气轮机等超高速设备中。基于实际超高速工况特点,对转速范围为10 000~120 000 r/min时的干气密封性能进行了系统性仿真计算,结果发现：在一定几何参数和工况参数下,类似于气浮轴承的微振动现象,干气密封会出现疑似受气体压力波动流影响的开启力、泄漏量与转速非正相关变化的扰流现象,尤其在高压、大膜厚、小槽深时的扰流效应愈加显著;在转速持续增大过程中,干气密封微尺度流场会出现二次拐点现象,且一次拐点发生转速与设计参数有关,而二次拐点发生转速基本约为90 000 r/min。同时结合导流织构的设计思路,进一步研究了超高速下干气密封槽底导流织构的驱动导流效应,结果表明：加设导流织构后,承载效果明显提高,拐点发生工况延后且压力波动区域被压缩。表明导流织构具有良好的抑制扰流、维持开启力与转速持续正相关的作用,在此基础上,进一步阐释了导流织构的抑扰机制,以期为突破干气密封在超高速工况下的应用壁垒提供新思路。     

基于定子电阻自适应辨识的感应电机死区补偿

电压源型逆变器由于死区效应,导致输出发生非标准化、畸变化,影响感应电机的控制精确度,特别是无速度传感器矢量控制,同时造成电网侧能量的流失。为了减小死区效应产生的影响,列出误差计算公式,求得总延时时间。另外,对定子电阻进行自适应辨识,增加所求延时时间精确度的同时可以运用到电机矢量控制中。经过补偿误差电压,提高了控制性能,降低了对控制系统的影响。结果表明所提补偿策略对电流波形、总谐波失真具有改善作用。     

一种开关磁阻电机无位置传感器控制效率优化策略

针对开关磁阻电机(SRM)的简化磁链法只能实现单相导通运行且导通区间固定的缺点,提出了一种结合固定关断角和自适应调节开通角的无位置传感器控制技术。利用曲线拟合关断位置磁链取代传统存储数据表,通过对比实时计算的动态磁链和曲线拟合的静态磁链,确定关断位置信号并估计转速和其他位置。考虑电机阻抗和电感的非线性特点,优化电感最小区域的开通角自调节模型确定导通区间。仿真结果验证了该方案的可行性和正确性,能够实现转子位置的间接检测,电机的运行效率得到进一步优化。     

Deformation behavior of non-rigid airships in wind tunnel tests

Deformation behavior of non-rigid airships in wind tunnel tests is studied by considering three factors, including internal pressure, flow velocity and angle of attack. Fiber Bragg grating strain sensors are used to measure the deformation of non-rigid airships. Wind tunnel tests in the case of different flow velocities and angles of attack are conducted. The measurement results reveal that the airship deformation is in proportion to internal pressure. For the tensile region,the airship deformation is in proportion to flow velocity. Effects of angle of attack on structural deformation are more complicated and there is no clear relationship existing between airship deformation and angle of attack.     

Fault diagnosis based on measurement reconstruction of HPT exit pressure for turbofan engine

Aero-engine gas path health monitoring plays a critical role in Engine Health Management(EHM). To achieve unbiased estimation, traditional filtering methods have strict requirements on measurement parameters which sometimes cannot be measured in engineering. The most typical one is the High-Pressure Turbine(HPT) exit pressure, which is vital to distinguishing failure modes between different turbines. For the case of an abrupt failure occurring in a single turbine component, a model-based sensor measurement reconstruction method is proposed in this paper. First,to estimate the missing measurements, the forward algorithm and the backward algorithm are developed based on corresponding component models according to the failure hypotheses. Then,a new fault diagnosis logic is designed and the traditional nonlinear filter is improved by adding the measurement estimation module and the health parameter correction module, which uses the reconstructed measurement to complete the health parameters estimation. Simulation results show that the proposed method can well restore the desired measurement and the estimated measurement can be used in the turbofan engine gas path diagnosis. Compared with the diagnosis under the condition of missing sensors, this method can distinguish between different failure modes, quantify the variations of health parameters, and achieve good performance at multiple operating points in the flight envelope.     

高速进气道出口快速撤锥再起动特性研究

为了探寻出口快速撤锥过程对高速进气道起动性能的影响,对二元高速进气道出口快速撤锥过程开展了非定常数值仿真研究。对比了进气道在一个喘振周期中从不同状态点处进行快速撤锥所表现出的起动性能的差异。研究表明,当来流马赫数低于进气道的加速自起动马赫数时,对于高速进气道因出口堵锥节流所引起的不起动流态(喘振),从不同喘振状态开始撤锥,进气道表现出不同的起动特性,而进气道最终能否顺利建立起动流态与快速撤锥时机的选取有关。     

一种引射增强型二次喉道新方案的数值模拟

为提高大型超声速风洞的运行经济性,设计了一种通过引射低总压冷介质提高扩压性能的新型二次喉道扩压器,其结构特征是在扩压器收敛段前方增加侧壁凹槽,在凹槽前沿位置引入低总压常温空气作为冷介质,通过引射扩散作用在扩压器壁面形成气膜,调节二次喉道实际流通直径,较大程度上增强二次喉道的静压恢复能力,同时又降低二次喉道壁面热负荷,冷却壁面。数值验证结果表明,所设计新型二次喉道方案可通过调节引射气量自适应较宽范围的运行条件,有效隔离扩压器壁面直接接触高温燃气,同时提高了扩压能力,节省后段接力引射器的主动流流量近30%,对风洞运行经济性提升十分明显。     

含硅芳炔树脂改性氰酸酯树脂的性能

将双酚E型氰酸酯(BEDCy)与含硅芳炔树脂(PSA)用溶液共混的方法制备了共混树脂(BEDCy/PSA);通过DSC和原位红外研究了共混树脂的固化反应,使用TGA和DMA表征了树脂的耐热性能;还考察了共混树脂的介电性能和力学性能.结果表明,PSA树脂能够降低BEDCy树脂的固化温度;随着PSA树脂的添加,氮气和空气氛...     

微型燃气轮机乙醇燃烧室点火与熄火试验

对应用于微型燃气轮机上的可再生生物质燃料乙醇燃烧室开展了试验研究,包括4种不同的供油方式,获得了常温常压进口条件下乙醇燃烧室的点火与熄火特性.研究结果表明:常温常压下采用旋流器的乙醇燃烧室的贫油点火和贫油熄火当量比的值均随空气流量的增加而减小,其点火与熄火性能优于预蒸发预混管燃烧室.