一种开关磁阻电机无位置传感器控制效率优化策略

针对开关磁阻电机(SRM)的简化磁链法只能实现单相导通运行且导通区间固定的缺点,提出了一种结合固定关断角和自适应调节开通角的无位置传感器控制技术。利用曲线拟合关断位置磁链取代传统存储数据表,通过对比实时计算的动态磁链和曲线拟合的静态磁链,确定关断位置信号并估计转速和其他位置。考虑电机阻抗和电感的非线性特点,优化电感最小区域的开通角自调节模型确定导通区间。仿真结果验证了该方案的可行性和正确性,能够实现转子位置的间接检测,电机的运行效率得到进一步优化。     

Deformation behavior of non-rigid airships in wind tunnel tests

Deformation behavior of non-rigid airships in wind tunnel tests is studied by considering three factors, including internal pressure, flow velocity and angle of attack. Fiber Bragg grating strain sensors are used to measure the deformation of non-rigid airships. Wind tunnel tests in the case of different flow velocities and angles of attack are conducted. The measurement results reveal that the airship deformation is in proportion to internal pressure. For the tensile region,the airship deformation is in proportion to flow velocity. Effects of angle of attack on structural deformation are more complicated and there is no clear relationship existing between airship deformation and angle of attack.     

Fault diagnosis based on measurement reconstruction of HPT exit pressure for turbofan engine

Aero-engine gas path health monitoring plays a critical role in Engine Health Management(EHM). To achieve unbiased estimation, traditional filtering methods have strict requirements on measurement parameters which sometimes cannot be measured in engineering. The most typical one is the High-Pressure Turbine(HPT) exit pressure, which is vital to distinguishing failure modes between different turbines. For the case of an abrupt failure occurring in a single turbine component, a model-based sensor measurement reconstruction method is proposed in this paper. First,to estimate the missing measurements, the forward algorithm and the backward algorithm are developed based on corresponding component models according to the failure hypotheses. Then,a new fault diagnosis logic is designed and the traditional nonlinear filter is improved by adding the measurement estimation module and the health parameter correction module, which uses the reconstructed measurement to complete the health parameters estimation. Simulation results show that the proposed method can well restore the desired measurement and the estimated measurement can be used in the turbofan engine gas path diagnosis. Compared with the diagnosis under the condition of missing sensors, this method can distinguish between different failure modes, quantify the variations of health parameters, and achieve good performance at multiple operating points in the flight envelope.     

高速进气道出口快速撤锥再起动特性研究

为了探寻出口快速撤锥过程对高速进气道起动性能的影响,对二元高速进气道出口快速撤锥过程开展了非定常数值仿真研究。对比了进气道在一个喘振周期中从不同状态点处进行快速撤锥所表现出的起动性能的差异。研究表明,当来流马赫数低于进气道的加速自起动马赫数时,对于高速进气道因出口堵锥节流所引起的不起动流态(喘振),从不同喘振状态开始撤锥,进气道表现出不同的起动特性,而进气道最终能否顺利建立起动流态与快速撤锥时机的选取有关。     

一种引射增强型二次喉道新方案的数值模拟

为提高大型超声速风洞的运行经济性,设计了一种通过引射低总压冷介质提高扩压性能的新型二次喉道扩压器,其结构特征是在扩压器收敛段前方增加侧壁凹槽,在凹槽前沿位置引入低总压常温空气作为冷介质,通过引射扩散作用在扩压器壁面形成气膜,调节二次喉道实际流通直径,较大程度上增强二次喉道的静压恢复能力,同时又降低二次喉道壁面热负荷,冷却壁面。数值验证结果表明,所设计新型二次喉道方案可通过调节引射气量自适应较宽范围的运行条件,有效隔离扩压器壁面直接接触高温燃气,同时提高了扩压能力,节省后段接力引射器的主动流流量近30%,对风洞运行经济性提升十分明显。     

含硅芳炔树脂改性氰酸酯树脂的性能

将双酚E型氰酸酯(BEDCy)与含硅芳炔树脂(PSA)用溶液共混的方法制备了共混树脂(BEDCy/PSA);通过DSC和原位红外研究了共混树脂的固化反应,使用TGA和DMA表征了树脂的耐热性能;还考察了共混树脂的介电性能和力学性能.结果表明,PSA树脂能够降低BEDCy树脂的固化温度;随着PSA树脂的添加,氮气和空气氛...     

考虑外圈局部缺陷的滚动轴承非线性动力特性

 建立了考虑滚动轴承外圈局部缺陷、非线性轴承力和径向游隙等非线性因素的滚动轴承系统动力学微分方程,并用Runge-Kutta-Felhberg算法对其求解。利用分岔图、Poincaré映射图、频谱图以及均方值、峰值因子、峭度等时域参数,分析了滚动轴承的响应、分岔和混沌等非线性动力特性。结果表明：考虑外圈局部缺陷的滚动轴承系统存在多种周期、拟周期和混沌响应;滚动轴承系统进入混沌的主要途径是倍周期分叉;峰值因子比率在中、低速,峭度比率在低速时可以很好地识别外圈局部缺陷。均方值比率除了在与轴承动力特性有关的个别转速外,可以在较大的转速范围识别外圈局部缺陷。     

台风多发区复杂场地设计风荷载参数比较

确定长大、高耸柔性结构设计风速是抗风设计的首要内容。对于我国东南沿海椒江入海口复杂场地条件,由周边气象站历史风速风向资料统计分析表明,利用规范建议的极值分布概型预测重现期设计风速存在不合理性,台风登陆衰减效应导致临近工程场地多个气象站极值风速预测结果差别较大,采用线性回归方法加权换算工程场地设计风速可以较为合理地定义结构设计基本风速。参考长三角地区Monte-Carlo台风随机模拟结果,进一步有针对性地分析了不同气候模式风环境参数取值对于结构风荷载取值的影响。     

离心式同向双旋流器空气雾化喷嘴雾化特性研究

对一种组合式的离心式同向双旋流器空气雾化喷嘴喷雾特性进行研究.双旋流器采用旋向相同的径向开孔式设计,在常温常压下试验,研究不同空气压力降和喷嘴供油压力工况下液雾的索太尔平均直径及分布指数.试验中以航空煤油为介质测试其雾化性能,采用马尔文激光测雾仪测量喷嘴下游50 mm处的液雾分布.结果表明:随着空气压力降和喷嘴供油压力的增大,索太尔平均直径减小,分布指数增大,推导了在空气压力降Δp/p＞3%和Δp/p＜3%两种工况下索太尔平均直径计算模型.      

颗粒阻尼对直升机旋翼桨叶减振效果的试验

 为探索直升机减振技术的新方法,研究颗粒阻尼技术在直升机旋翼桨叶减振中的应用,设计了直升机旋翼桨叶模型及其相应的颗粒阻尼器形式,利用试验方法研究了颗粒阻尼对非旋转及旋转桨叶模型的阻尼减振效果。试验结果表明：颗粒阻尼可以有效提高非旋转桨叶模型的前3阶阻尼水平,尤其可使桨叶第3阶模态阻尼比提高一个数量级甚至更多;在较低的转速范围内,颗粒阻尼还可以克服离心力作用,使旋转桨叶模型的挥舞和摆振加速度响应水平均得到有效削减,充分表明了颗粒阻尼作为一种振动控制手段应用于直升机旋翼桨叶的可行性。