全文获取类型
收费全文 | 1198篇 |
免费 | 242篇 |
国内免费 | 264篇 |
专业分类
航空 | 800篇 |
航天技术 | 287篇 |
综合类 | 204篇 |
航天 | 413篇 |
出版年
2024年 | 2篇 |
2023年 | 8篇 |
2022年 | 21篇 |
2021年 | 29篇 |
2020年 | 36篇 |
2019年 | 27篇 |
2018年 | 25篇 |
2017年 | 15篇 |
2016年 | 31篇 |
2015年 | 43篇 |
2014年 | 66篇 |
2013年 | 73篇 |
2012年 | 70篇 |
2011年 | 94篇 |
2010年 | 96篇 |
2009年 | 101篇 |
2008年 | 78篇 |
2007年 | 72篇 |
2006年 | 69篇 |
2005年 | 45篇 |
2004年 | 37篇 |
2003年 | 54篇 |
2002年 | 78篇 |
2001年 | 72篇 |
2000年 | 39篇 |
1999年 | 65篇 |
1998年 | 62篇 |
1997年 | 51篇 |
1996年 | 45篇 |
1995年 | 33篇 |
1994年 | 37篇 |
1993年 | 27篇 |
1992年 | 14篇 |
1991年 | 15篇 |
1990年 | 26篇 |
1989年 | 18篇 |
1988年 | 8篇 |
1987年 | 10篇 |
1986年 | 7篇 |
1985年 | 1篇 |
1984年 | 2篇 |
1981年 | 1篇 |
1965年 | 1篇 |
排序方式: 共有1704条查询结果,搜索用时 156 毫秒
991.
本文应用弹塑性有限元数值计算及参数化设计方法,对飞行器典型连接件结构的有限元计算进行了参数化设计,并基于ANSYS平台开发了参数化的连接件结构有限元仿真系统,借助通用有限元软件ANSYS的参数化设计语言APDL与界面设计语言UIDL,完成参数化建模的宏文件设计与参数输入的界面设计及参数传递,初步实现了有限元建模、计算和后处理的全程参数化;实现了对ANSYS的二次开发;利用有限元的子模型技术,在计算开销相对较小的情况下保证了计算精度,从而形成专业化、参数化、高效率的连接件有限元仿真设计系统。文中给出了采用该系统与传统方法比较的算例,可以看出结果有较好的吻合。 相似文献
992.
993.
994.
研究了基于机匣测点信号进行航空发动机滚动轴承故障诊断的灵敏性问题.首先利用两个带机匣的航空发动机转子试验器进行了冲击响应试验,比较了滚动轴承处冲击激励引起的轴承座测点响应和机匣测点响应的差别;然后利用这两个带机匣的转子试验器进行了滚动轴承故障模拟试验,详细对比分析了轴承座测点信号和机匣测点信号的时域波形、频谱和小波包络谱.结果表明:当滚动轴承和机匣的连接刚度较小时,故障滚动轴承的振动信号传递到机匣上时会产生很大的衰减,然而利用传统的基于小波包变换的包络解调方法仍然可以很好地诊断出外圈故障和内圈故障,对于滚动体故障的诊断效果略差.研究结果对于实际中基于机匣测点信号进行航空发动机滚动轴承故障诊断提供了试验依据. 相似文献
995.
郭亚林%梁国正%丘哲明%刘爱华 《宇航材料工艺》2006,36(5):30-33
研究了一种有机硅改性环氧树脂的固化反应。利用红外光谱法分析了树脂的组成结构,固化剂的选择及其用量的确定,并利用DSC对固化反应动力学进行了研究,计算出了固化反应的动力学常数,对固化反应的机理进行了分析。结果表明:该有机硅改性环氧树脂是由苯基硅树脂与E型环氧树脂相互反应而合成的,可采用聚酰胺在室温下进行固化,固化反应主要发生在环氧基与伯胺之间,反应的表观活化能为67.555 kJ/mol,频率因子为1.48×106s-1。本研究可为该有机硅改性环氧树脂成型工艺的制定提供理论指导。 相似文献
996.
997.
Crashworthiness of a civil airplane fuselage section was studied in this paper. Firstly, the failure criterion of a rivet was studied by test, showing that the ultimate tension and shear failure loads were obviously affected by the loading speed. The relations between the loading speed and the average ultimate shear, tension loads were expressed by two logarithmic functions. Then, a vertical drop test of a civil airplane fuselage section was conducted with an actual impact velocity of6.85 m/s, meanwhile the deformation of cabin frame and the accelerations at typical locations were measured. The finite element model of a main fuselage structure was developed and validated by modal test, and the error between the calculated frequencies and the test ones of the first four modes were less than 5%. Numerical simulation of the drop test was performed by using the LS-DYNA code and the simulation results show a good agreement with that of drop test. Deforming mode of the analysis was the same as the drop test; the maximum average rigid acceleration in test was 8.81 g while the calculated one was 9.17 g, with an error of 4.1%; average maximum test deformation at four points on the front cabin floor was 420 mm, while the calculated one was 406 mm, with an error of 3.2%; the peak value of the calculated acceleration at a typical location was 14.72 g, which is lower than the test result by 5.46%; the calculated rebound velocity result was greater than the test result 17.8% and energy absorption duration was longer than the test result by 5.73%. 相似文献
998.
999.
1000.