先进的短距起飞垂直降落(ASTOVL)升力风扇飞机的动态逆控制

研究了推力矢量喷管、升力风扇以及气动舵面共同作用下 ASTOVL升力风扇飞机的飞控问题 ,采用非线性动态逆理论进行控制系统的设计。针对 ASTOVL升力风扇飞机的俯仰控制设计了动态逆控制律 ,并将所设计的控制律进行了仿真。结果表明 ,该方法能够满足控制系统性能的要求 ,具有工程应用前景。     

场协同原理在高超声速化学非平衡流动中的推广

应用理论分析与数值模拟方法,将对流传热的场协同原理从不可压缩流动推广至高超声速化学非平衡流动中。结果表明,高超声速化学非平衡层流与湍流的热流密度取决于流动的当地单位体积的动量与单位质量总焓梯度的协同。用当地单位体积的动量与单位质量总焓梯度的协同研究高超声速化学非平衡流动的壁面传热问题,对层流流动下的对流传热,不但计及了高超声速化学非平衡流的密度变化对热流密度的影响,而且包括了静焓梯度、压力梯度、边界层内的分子黏性剪切效应对热流密度的作用;对湍流问题,除了上述层流流动各项对热流密度的影响外,还计及了雷诺剪切应力对热流密度的作用。考虑到高超声速化学非平衡流静焓的定义,高超声速化学非平衡层流及湍流的场协同同时计及所有组分的平动能、转动能、振动能及电子能等梯度的贡献。     

基于混杂非对称复合材料的自适应对日定向器

提出并设计了一种基于混杂非对称复合材料层合板的新型自适应对日定向器。该对日定向器采用混杂非对称复合材料层合板作为驱动元件,利用在轨光照条件的变化引起复合材料层合板温度变化,进而使其产生热变形并驱动太阳翼发生偏转。提出的自适应对日定向器结合传统的单自由度对日定向机构,能够实现太阳能帆板的双自由度对日定向。介绍了自适应对日定向器的基本原理,并结合地球静止轨道的光照条件进行了具体设计。利用能量变分原理建立了混杂非对称复合材料的热变形模型,分析其热变形特点,并利用有限元方法对定向器在地球静止轨道上的温度场特性、热变形及对日定向转动角度进行分析。有限元分析结果表明,通过合理设计,自适应对日定向器的转角能够随太阳光入射角变化呈线性变化,定向精度可达±1°。     

A New D-GCL for Unidirectional Motion with Large Displacement

Numerical simulations of unsteady flow problems with moving boundaries commonly require the use of geometric conservation law(GCL).However,in cases of unidirectional large mesh deformation,the cumulative error caused by the discrete procedure in GCL can significantly increase,and a direct consequence is that the calculated cell volume may become negative.To control the cumulative error,a new discrete GCL(D-GCL)is proposed.Unlike the original D-GCL,the proposed method uses the control volume analytically evaluated according to the grid motion at the time level n,instead of using the calculated value from the D-GCL itself.Error analysis indicates that the truncation error of the numerical scheme is guaranteed to be the same order as that obtained from the original D-GCL,while the accumulated error is greatly reduced.For validation,two challenging large deformation cases including a rotating circular cylinder case and a descending GAW-(1)two-element airfoil case are selected to be investigated.Good agreements are found between the calculated results and some other literature data,demonstrating the feasibility of the proposed D-GCL for unidirectional motions with large displacements.     

多星多普勒频率变化率无源定位方法

针对多星时差频差定位系统时/频同步要求高、多星测向定位系统复杂等问题,提出一种多星多普勒频率变化率的无源定位体制,每颗卫星仅需单个接收天线和通道,且多星之间无需高精度时/频同步。针对定位观测量与辐射源位置的高度非线性,提出一种基于多普勒频率的多假设非线性最小二乘(MH-NLS)无源定位算法。理论推导了定位估计的克拉美-罗下限(CRLB),基于定位误差的几何分布(GDOP)分析了多星构型对定位误差的影响。计算机仿真分析表明,基于多普勒频率变化率的MH-NLS算法得到的定位误差能够达到CRLB。     

弧齿锥齿轮齿面拓扑修形及加工参数计算

为了能够实现对齿面啮合性能的灵活控制,针对弧齿锥齿轮小轮提出一种齿面拓扑修形方法,即借助二阶曲面对齿面偏差拓扑的近似表达,将齿面拓扑修形分解为5个方向:螺旋角修正、压力角修正、齿长曲率修正、齿廓曲率修正及齿面挠率修正,通过改变5个方向的修形系数对小轮齿面拓扑结构进行自由控制。在此基础上,建立齿面偏差与机床加工参数之间的修正数学模型,通过构建敏感性矩阵并采用最小二乘法求解,反求出获得修形齿面的小轮加工参数,以便指导加工。以一对弧齿锥齿轮副为例进行修形啮合分析,仿真结果表明:选取齿长曲率修形系数为0.0001,齿廓曲率修形系数为0.0005,齿面挠率修形系数为0.0003,对齿面进行拓扑修形后传动误差幅值为-25.60″,接触迹线倾斜角度变为54.7°,相比原始结果啮合性能得到改善。滚检接触区与理论仿真结果一致,验证了修形方法的有效性。      

Drag derived altitude aided navigation method

The navigation problem of the lifting reentry vehicles has attracted much research interest in the past decade.This paper researches the navigation in the blackout zone during the reentry phase of the aircraft,when the communication signals are attenuated and even interrupted by the blackout zone.However,when calculating altitude,a pure classic inertial navigation algorithm appears imprecise and divergent.In order to obtain a more precise aircraft altitude,this paper applies an integrated navigation method based on inertial navigation algorithms,which uses drag derived altitude to aid the inertial navigation during the blackout zone.This method can overcome the shortcomings of the inertial navigation system and improve the navigation accuracy.To further improve the navigation accuracy,the applicable condition and the main error factors,such as the atmospheric coefficient error and drag coefficient error are analyzed in detail.Then the damping circuit design of the navigation control system and the damping coefficients determination is introduced.The feasibility of the method is verified by the typical reentry trajectory simulation,and the influence of the iterative times on the accuracy is analyzed.Simulation results show that iterative three times achieves the best effect.     

临近空间高超声速目标滑跃式轨迹Sine-AIMM跟踪算法

针对单一的Sine模型算法无法与临近空间高超声速目标滑跃式轨迹准确匹配,现有的交互多模型(IMM)算法跟踪效果也不够理想的问题,提出一种基于多重贝叶斯准则的自适应交互式多Sine模型(Sine-AIMM)临近空间高超声速滑跃式目标跟踪算法.算法采用多个Sine模型对滑跃式轨迹进行匹配,并利用多重贝叶斯准则在线调整各模型...     

空射导弹发射初始弹道数值仿真

导弹从载机上发射时,载机对导弹的流场存在干扰,从而影响导弹在发射初始阶段的姿态和运动轨迹。为了确定导弹的初始弹道参数,本文利用CFD商业软件Fluent6.1计算导弹发射时的非定常流场,并通过该软件的接口嵌入导弹的六自由度弹道方程,同时计算了导弹在载机流场干扰下的非定常气动力和初始弹道。计算结果清晰地表现出导弹与载机的分离过程和载机流场的干扰形式,并可估算出载机的流场干扰范围。     

基于对偶四元数的捷联惯导算法在发射点惯性系下的应用研究

针对导弹类载体在做复杂的高动态机动时,采用传统的捷联惯导算法容易产生圆锥误差与划船误差,从而导致解算精度降低的问题,在发射点惯性系下设计了基于对偶四元数的捷联惯导算法.在建立发射点惯性系下的捷联惯导解算模型的基础上,详细推导了基于对偶四元数的捷联惯导解算算法,通过对比分析其中的速度更新过程与传统算法的差异,说明该算法可...