CBERS-1卫星IRMSS数据在城市绿地系统规划的应用

文章以CBERS -1卫星长沙幅IRMSS数据作为基础资料 ,利用PCI遥感图像处理软件对数据进行了预处理和应用实验。实验证明CBERS -1卫星的IRMSS数据图像信息丰富 ,可解译程度较高 ,能满足大中城市中等比例尺城市绿地系统规划遥感调查的要求     

等质量异形粒子超高速撞击侵蚀

用数值方法模拟双锥，圆柱，椭球、圆锥和倒圆锥五类等质量异形铝粒子五种高宽比共２５种粒子对半无限铝靶的超高速撞击侵蚀，撞击速度为４ｋｍ／ｓ，给出了坑深、坑径、坑形参数和坑体积随粒子形状及高宽比的变化曲线。结果与非圆球异形粒子超高速撞击侵蚀计算有重要参考价值。     

备件配置方法研究

针对电路板件故障数据记录的实际,运用可靠性理论,提出了没有故障数据板件的备件数量计算方法;对有故障统计数据的板件引用了经验模型来确定备件配置。     

用于高压动态校准的快开阀装置

介绍一种高压快开阀装置。它可产生３７０ＭＰａ上升时间小于２０μｓ的阶跃压力，用于对高压传感器进行动态校准。     

一种新的六端口测量系统自校准方法

提出了一种新的六端口自校准方法.本方法从六端口相对功率理论出发,导出了六端口系统常数的自校准方程,给出了求解系统常数初值的方法,并利用梯度法对方程组求解,仿真结果表明用一个匹配负载、四个失配负载就可以解出系统常数.     

Digital Aircraft Sheet Metal Part Manufacturing System and Its Key Technology

The architecture of digital sheet metal manufacturing system is proposed based on the classification of sheet metal manufacturing information.The essence of digital manufacturing is the definition,management and transfer of information,and the key technologies are brought forward and described.It is pointed out that knowledge-based manufacturing elements design is necessary to make digital technology efficient.The management of all kinds of sheet metal manufacturing element information is to build single source of manufacturing data.Multi-state model-based digital transfer and coordination method is designed to provide a foundation for digital manufacturing of aircraft sheet metal part.The application of digital sheet metal manufacturing is exemplified with an aircraft sheet metal part.The application result is compared to that of the traditional analog transfer technology.It is shown that the developed technology can improve part quality,shorten manufacturing time and lower manufacturing cost.     

Implementation of a novel matrix converter PMSM drive

This paper proposes a neural-network current-regulated switching strategy and an intelligent controller for a matrix converter permanent magnet synchronous motor (PMSM) drive system. By using this new switching strategy, the current harmonics of the system are effectively reduced. In addition, by using the intelligent controller, position control of the drive system can be achieved and an adjustable speed range from 1 r/min to 1500 r/min can be obtained. All the current-loop, speed-loop, and position-loop control algorithms are implemented by a 32-bit TMS320C40 digital signal processor. Several experimental results are shown to validate the theoretical analysis     

Power anomaly effects and costs in low-voltage mobile power systems

Electric power anomalies or disturbances can disrupt the normal operation of equipment, accelerate aging, or even cause outright failures thus resulting in increased costs of maintenance and reduced system reliability. Past research on the effects caused by power anomalies has been mostly focused on industrial, commercial, or residential systems, or on power distribution equipment. A literature survey reveals that there is no comprehensive review related to low-voltage (LV) power systems and utilization equipment applicable to military combat vehicles, such as aircraft and ships. This paper summarizes the results of a new literature survey that focused on the causes, effects, and mitigation methods for power anomalies typical of LV mobile power systems. Electric power anomaly cost data collected from the literature are also presented, from which the costs of anomalies to the national defense are estimated using some simple rationales.     

CBERS-1卫星红外多光谱扫描仪扫描子系统

文章介绍了CBERS -1卫星红外多光谱扫描仪(IRMSS)关键部件扫描子系统研制与应用情况。     

基于PCI总线的石英晶体元件电参数测试仪

首先介绍PCI总线控制专用芯片S5920的组成,Mailboxs、FIFO、Pass-Thru的基本概念、性能和使用方法。其次介绍测量石英晶体元件参数的阻抗计法和π网络法。对基于PCI总线控制器S5920为核心的π网络法石英晶体元件电参数测试仪的设计和实现作了说明。该方法测量的频率可达2005MHz。利用GPs高精度的授时信号作为频率校准信号校准信号源的精度。