带有闭式布雷顿循环的预冷发动机特性研究

为获取带有闭式布雷顿循环的预冷发动机的飞行包线及性能,同时提高发动机工程实现的可行性,基于带有闭式布雷顿循环的预冷发动机基础循环及现有部件技术水平,构建了一种适度预冷发动机方案.对该方案下发动机沿着SABRE3飞行轨迹下的性能和部件匹配规律进行了分析.然后通过对发动机的高度、速度、调节特性进行研究,得到了该方案下发动机...     

厘米-分米波段Ⅲ型爆发的统计分析

统计分析了太阳第23周期间(2000年7月至2004年9月)在625~1500,MHz,2600~3800,MHz和5200~7600,MHz范围频谱仪观测到的Ⅲ型射电爆发. 给出了Ⅲ型爆发的分布、寿命、频率漂移率、偏振度和频率带宽. 结果显示, 频率漂移率和频率带宽的平均值随频率的增加而增大, 寿命和偏振度的平均值既不是常数也不是在宽频延伸上保持均匀不变的.最多的Ⅲ型爆发分布在625~3800,MHz范围内, 且随频率的增加而增多. 分析表明, 电子加速和能量释放地点主要是在分米波范围内, 这个频率范围的特征可能与分米波段上的磁位形有关, 并且与主耀斑地点附近磁重联区中的电子加速有关. 然而, 还有相当数量的Ⅲ型爆发发生在5200~7600,MHz范围内, 这个特征表明电子加速的地点是在一个日冕的宽范围中. 关于厘米relax-relax 分米波段Ⅲ型爆发的辐射机制最可能包含相干的等离子体辐射或电子回旋脉泽辐射过程.     

太阳活动与全球气候变化

太阳不断向地球辐射电磁波和粒子, 太阳辐射是地球气候系统最主要的能量来源. 地球气候系统对太阳活动的响应是一个复杂的过程, 包括辐射过程、动力学过程以及微观物理过程等. 根据太阳辐射的卫星观测结果和重建结果, 例举了古气候、温度、大气环流和云量等方面太阳影响气候的观测证据, 论述了太阳影响气候的三种可能机制, 即太阳总辐射变化可以影响地表温度, 并通过海-气耦合改变大气环流; 太阳紫外辐射通过调制平流层的温度和风场影响下面的对流层; 太阳通过行星际磁场调制银河宇宙线, 而银河宇宙线通过电离大气影响云量, 进而改变地球的能量收支.     

面向北斗导航电文认证的符号级欺骗方法研究

针对目前的月面定位技术中成本高、观测时间长以及缺少可用定位信息的问题,开展了基于长期演进（LTE）基站的月面定位技术的研究,并引入了LTE技术,通过在月面布设基站为月面巡视器的实时定位提供了可行基础。提出了一种基于因子图优化的月面定位方法,通过融合月面基站的正交频分复用（OFDM）测距信息和巡视器自身的惯性导航信息,利用有限的月面基础设施,在较低成本的硬件条件下实现了月面巡视器的准确定位。仿真实验结果显示,该月面定位方法具有良好的准确性和鲁棒性。     

基于加工误差仿真的半球谐振子优化设计

针对半球谐振陀螺谐振子制造过程中存在的加工误差,采用有限元仿真,分析了半球谐振子结构参数、尺寸公差和形位公差变化对其工作模态频率和临近模态频率的影响,研究了半球谐振子形位公差变化对频率裂解和品质因数的影响。通过仿真分析可知,半球谐振子结构参数壁厚、半球中心半径及内倒角半径都会影响模态频率;半球谐振子形位公差中的内外球心距离误差对其工作模态影响较大,中心轴平行误差对频率裂解和品质因数影响较大;半球谐振子壁厚、内倒角半径、小柱半径及内外球心距离误差变化会使工作模态频率与相邻模态间存在干扰。在此基础上,提出了半球谐振子结构参数及形位公差优化设计建议,并通过半球谐振子品质因数Q值和频率裂解测量对该建议进行了验证。     

Multi-mode optimal fuzzy active vibration control of composite beams laminated with photostrictive actuators

Firstly, a multi-field coupling finite element formulation of composited beam laminated with the photostrictive actuators is developed in this paper. Moreover, an optimal fuzzy active control algorithm is also proposed on the basis of the combination of optimal control and fuzzy one.This method opens a new avenue to resolve the contradiction between the linear system control method and nonlinear actuating characteristics of photostrictive actuators. The desired control for suppressing multi-modal vibration of photoelectric laminated beam is firstly obtained through optimal control and then the fuzzy control is used to approach the desired mechanical strain induced by photostrictive actuators. Thus, the multi-mode vibration control of beam is realized.In the design process of optimal fuzzy controller, the design of fuzzy control is independent of optimal control. The simulation results demonstrate that the proposed control method can effectively realize multi-modal vibration control of photoelectric laminated beams, and the control effect of optimal fuzzy control is better than that of optimal state feedback control.     

电子束表面造型对液冷冷板散热性能影响研究

为了获得电子束表面造型对液冷冷板散热性能的影响规律,对带有柱状表面造型的液冷冷板进行数值模拟。结果表明,当冷却液通道中存在柱状表面造型时,可有效提高冷板的散热性能,其中造型高度对冷板的散热性能影响最大,造型流向间距的影响其次,造型直径的影响最小;当柱状造型直径1mm、高度6mm且相邻造型的流向间距为4mm时,冷却液与模拟发热芯片的温差为46.08℃,该冷板的散热性能与空白试样对比可提升23.23%。之后根据模拟结果,制备了具有不同表面造型特征的液冷冷板试样,散热性能测试结果表明,通道内制备柱状造型可提高冷板散热性能达13%以上;但当柱状造型高度4mm,且造型数量较少时,改变柱状造型特征对提升冷板散热性能的影响较小。     

Crystal orientation and morphology of a lamellae in wrought titanium alloys: On the role of microstructure evolution in b processing

To obtain high-quality aviation forgings of titanium alloys, b forging is an essential processing step which must be considered throughout a production process. In this work, the effect of b forging on the crystal orientation and morphology of lamellar a was experimentally investigated in a two-phase titanium alloy. Strong dynamic recovery during b working resulted in the formation of low-angle grain boundary(LAGBb) inside b grains. The lamellar a can penetrate through the LAGBb, leading to similar intra a LAGBs on subgrain boundaries. Deformation banding occurs at high strain rates, and both diffusive and sharp boundaries of deformation bands can be observed.A continuous change of the b orientation in diffusive boundaries results in the formation of fine and disordered a lamellae without intra-lamellar boundary to hold the Burgers orientation relationship(OR). On sharp boundaries, it is prone to producing continuous grain boundary a(aGB) with a highly similar orientation along the boundaries. Meanwhile, there may exist several lower-angle boundaries within the grain boundary a for a smoother orientation change on the b grain boundary.     

Multi-level virtual prototyping of electromechanical actuation system for more electric aircraft

Electromechanical actuators (EMAs) are becoming increasingly attractive in the field of more electric aircraft because of their outstanding benefits, which include reduced fuel burn and maintenance cost, enhanced system flexibility, and improved management of fault detection and isolation. However, electromechanical actuation raises specific issues when being used for safety-critical aerospace applications like flight controls: huge reflected inertia to load, jamming-type failure, and increase of backlash with service due to wear and local dissipation of heat losses for thermal balance. This study proposes an incremental approach for virtual prototyping of EMAs. It is driven by a model-based system engineering process in order to enable simulation-aided design. Best practices supported by Bond graph formalism are suggested to develop a model’s structure efficiently and to make the model ready for use (or extension) by addressing the above mentioned issues. Physical effects are progressively introduced, and the realism of lumped-parameter models is increased step-by-step. In particular, multi-level component models are architected to ensure continuity between engineering activities. The models are implemented in the AMESim simulation environment, and simulation responses are given to illustrate how they can be used for preliminary sizing, control design, thermal balance verification, and faults to failure analysis. The proposed best practices intend to provide engineers with fast, reusable, and efficient means to assess performance virtually and enhance maturity, performance, and robustness.     

基于LMS Virtual. Lab的系留气球仿真与优化

系留气球在近地面收放过程中存在俯仰角过大的问题，为了更全面地了解收放过程中不同因素对球体俯仰角的影响，采用LMS Virtua1. Lab建立了带滑轮索具系统的系留气球三维动力学模型进行仿真分析，结果表明，仿真结果与理论计算、测量数据都有较高的符合度。进而运用试验设计( DOE)方法，探索典型风速下球体俯仰角的响应区间。最后基于响应面模型的优化技术，对滑轮索具系统设计进行优化，有效改善了球体在收放过程中俯仰角过大的问题。仿真模型对系留气球系统设计及收放控制有一定的指导作用。