DSP的数学原理及在实时系统的应用

制造系统里所用的微处理器中，单片机只能做逻辑处理和简单数学计算，而数字信号处理器（DSP）可进行相当复杂的数学处理。本文概述DSP的数学原理及其技术特点，介绍了基于DSP智能控制器在制造业中实时测控系统的应用实例。     

俯仰振荡三角翼在非定常自由流中运动的实验

在南京航空航天大学已建成的国内首座非定常风洞内,研制了一套单自由度俯仰振荡实验装置,设计开发了一套对模型姿态和来流风速进行联合控制的软件。对一60°后掠三角翼模型进行了单独俯仰振荡运动和俯仰振荡与自由来流耦合运动的实验。实验结果表明:模型做单独俯仰振荡时,振动频率和振动幅值的影响只有在迟滞环出现后才起作用,而迟滞环的出现是由于翼面上的不同流态对外界扰动的反应时间不同造成的。非定常自由流对做俯仰振荡的三角翼气动特性有很大的影响,模型上仰过程中来流的减速,进一步提高了最大升力系数,推迟了失速迎角;模型下俯过程中来流的加速,则更进一步推迟了升力系数恢复到静态时的值。当翼面上产生破碎涡流时,非定常自由流的作用表现得更为明显。     

太阳微波爆发频谱事件

国家天文台1.0-2.0GHz,2.6-3.8GHz太阳射电频谱仪从1994年1月和1996年9月投入观测至2000年4月10日记录到太阳射电爆发分别为297个和316个，取得了高质量的高时间分辨率，高频率分辨率的动态谱资料，为研究耀斑各种尺度的时间及空间演化过程提供了丰富的信息，1998年4月15日的共同事件在时间和频率上显示了丰富的幅度和结构的变化。     

模拟月壤研制的初步设想

模拟月壤是月球样品的地球化学复制品，作者总结世界上已有的5种模拟月壤JSC-1，MLS．1，MLS-2，MKS-1和FJS-1的研制过程、方法与基本理化性质，认为系列化模拟月壤研制对中国首次月球探测有重要意义，在此基础上，作者提出系列化模拟月壤研制的基本思路．     

线阵CCD平场校正及FPGA实现的研究

为了消除由于照明光源的非均匀性、镜头渐晕及CCD传感器噪声对图像质量造成的不良影响,首先从理论上分析了线阵CCD固定模式噪声和像素光电响应非均匀性的数学模型和产生的原因;对像素光电响应非均匀性这一主要影响因素,根据其光电响应模型提出了CCD像素光电响应非均匀性的两点校正方法,即求解出各个像素光电响应不均匀性的校正因子和暗偏置量系数,进而用以计算各个像素的校正量,实现逐点校正;针对校正算法大数据量、实时计算的要求,设计了基于现场可编程逻辑门阵列FPGA快速实现校正算法的硬件处理结构。最后,通过仿真和实验表明,两点校正方法可以有效地减小CCD像素光电响应不均匀性的图像噪声,提高图像质量,以便做后续精确处理。     

Multi-mode optimal fuzzy active vibration control of composite beams laminated with photostrictive actuators

Firstly, a multi-field coupling finite element formulation of composited beam laminated with the photostrictive actuators is developed in this paper. Moreover, an optimal fuzzy active control algorithm is also proposed on the basis of the combination of optimal control and fuzzy one.This method opens a new avenue to resolve the contradiction between the linear system control method and nonlinear actuating characteristics of photostrictive actuators. The desired control for suppressing multi-modal vibration of photoelectric laminated beam is firstly obtained through optimal control and then the fuzzy control is used to approach the desired mechanical strain induced by photostrictive actuators. Thus, the multi-mode vibration control of beam is realized.In the design process of optimal fuzzy controller, the design of fuzzy control is independent of optimal control. The simulation results demonstrate that the proposed control method can effectively realize multi-modal vibration control of photoelectric laminated beams, and the control effect of optimal fuzzy control is better than that of optimal state feedback control.     

电子束表面造型对液冷冷板散热性能影响研究

为了获得电子束表面造型对液冷冷板散热性能的影响规律,对带有柱状表面造型的液冷冷板进行数值模拟。结果表明,当冷却液通道中存在柱状表面造型时,可有效提高冷板的散热性能,其中造型高度对冷板的散热性能影响最大,造型流向间距的影响其次,造型直径的影响最小;当柱状造型直径1mm、高度6mm且相邻造型的流向间距为4mm时,冷却液与模拟发热芯片的温差为46.08℃,该冷板的散热性能与空白试样对比可提升23.23%。之后根据模拟结果,制备了具有不同表面造型特征的液冷冷板试样,散热性能测试结果表明,通道内制备柱状造型可提高冷板散热性能达13%以上;但当柱状造型高度4mm,且造型数量较少时,改变柱状造型特征对提升冷板散热性能的影响较小。     

Crystal orientation and morphology of a lamellae in wrought titanium alloys: On the role of microstructure evolution in b processing

To obtain high-quality aviation forgings of titanium alloys, b forging is an essential processing step which must be considered throughout a production process. In this work, the effect of b forging on the crystal orientation and morphology of lamellar a was experimentally investigated in a two-phase titanium alloy. Strong dynamic recovery during b working resulted in the formation of low-angle grain boundary(LAGBb) inside b grains. The lamellar a can penetrate through the LAGBb, leading to similar intra a LAGBs on subgrain boundaries. Deformation banding occurs at high strain rates, and both diffusive and sharp boundaries of deformation bands can be observed.A continuous change of the b orientation in diffusive boundaries results in the formation of fine and disordered a lamellae without intra-lamellar boundary to hold the Burgers orientation relationship(OR). On sharp boundaries, it is prone to producing continuous grain boundary a(aGB) with a highly similar orientation along the boundaries. Meanwhile, there may exist several lower-angle boundaries within the grain boundary a for a smoother orientation change on the b grain boundary.     

Multi-level virtual prototyping of electromechanical actuation system for more electric aircraft

Electromechanical actuators (EMAs) are becoming increasingly attractive in the field of more electric aircraft because of their outstanding benefits, which include reduced fuel burn and maintenance cost, enhanced system flexibility, and improved management of fault detection and isolation. However, electromechanical actuation raises specific issues when being used for safety-critical aerospace applications like flight controls: huge reflected inertia to load, jamming-type failure, and increase of backlash with service due to wear and local dissipation of heat losses for thermal balance. This study proposes an incremental approach for virtual prototyping of EMAs. It is driven by a model-based system engineering process in order to enable simulation-aided design. Best practices supported by Bond graph formalism are suggested to develop a model’s structure efficiently and to make the model ready for use (or extension) by addressing the above mentioned issues. Physical effects are progressively introduced, and the realism of lumped-parameter models is increased step-by-step. In particular, multi-level component models are architected to ensure continuity between engineering activities. The models are implemented in the AMESim simulation environment, and simulation responses are given to illustrate how they can be used for preliminary sizing, control design, thermal balance verification, and faults to failure analysis. The proposed best practices intend to provide engineers with fast, reusable, and efficient means to assess performance virtually and enhance maturity, performance, and robustness.     

基于LMS Virtual. Lab的系留气球仿真与优化

系留气球在近地面收放过程中存在俯仰角过大的问题，为了更全面地了解收放过程中不同因素对球体俯仰角的影响，采用LMS Virtua1. Lab建立了带滑轮索具系统的系留气球三维动力学模型进行仿真分析，结果表明，仿真结果与理论计算、测量数据都有较高的符合度。进而运用试验设计( DOE)方法，探索典型风速下球体俯仰角的响应区间。最后基于响应面模型的优化技术，对滑轮索具系统设计进行优化，有效改善了球体在收放过程中俯仰角过大的问题。仿真模型对系留气球系统设计及收放控制有一定的指导作用。