Concept of monitoring for thermostressed state and service life of aircraft gas turbine engine blades

A concept of monitoring for material properties with residual life estimation of rotor blades for gas turbine engines is proposed. The structure of on-board control and conditionmonitoring system based on the intelligent pyrometer module with the algorithm for calculating the residual life of turbine rotor blades is described.     

Analysis of a beam with a crack under irregular cyclic load

This paper considers a beam with a technological longitudinal section on the level of the gravity center of the cross section that is loaded by a vertical concentrated force. We study the structure durability depending on the load amplitude and the initial crack length.     

Improvement of gas-dynamic efficiency of GTE gas turbine stages at the design stage

Methods to control flow have been considered in order to reduce end losses in blade rows of GTE gas turbines by means of measures taken at the design stage.     

Dynamics and de-spin control of massive target by single tethered space tug

This paper investigates the dynamics and de-spin control of a massive target by a single tethered space tug in the post-capture phase. The dynamic model of the tethered system is derived and simplified to a dimensionless form. Further, a decoupled PD controller is proposed, and the local stability of the controller is analyzed by linearization technique. Parametric studies of the dynamics and de-spin control of a massive target are conducted to characterize the dynamic process of de-spin with the proposed control law. It is shown that the massive target can be de-span by a single and small space tug with limited thrust within finite time. The thrust tangent with the tether de-spins the target while the thrust normal to the tether prevents the tether from winding up the target. The tether length has a positive contribution to the de-spin of a target. The longer tether leads to a faster de-spin process.     

An evolutionary computational framework for capacity-safety trade-off in an air transportation network

Airspace safety and airport capacity are two key challenges to sustain the growth in Air Transportation. In this paper, we model the Air Transportation Network as two sub-networks of airspace and airports, such that the safety and capacity of the overall Air Transportation network emerge from the interaction between the two. We propose a safety-capacity trade-off approach,using a computational framework, where the two networks can inter-act and the trade-off between capacity and safety in an Air Transport Network can be established. The framework comprise of an evolutionary computation based air traffic scenario generation using a flow capacity estimation module(for capacity), Collision risk estimation module(for safety) and an air traffic simulation module(for evaluation). The proposed methodology to evolve air traffic scenarios such that it minimizes collision risk for given capacity estimation was tested on two different air transport network topologies(random and small-world) with the same number of airports. Experimental results indicate that though airspace collision risk increases almost linearly with the increasing flow(flow intensity) in the corresponding airport network, the critical flow depend on the underlying network configuration. It was also found that, in general, the capacity upper bound depends not only on the connectivity among airports and their individual performances but also the configuration of waypoints and mid-air interactions among conflicts. Results also show that airport network can accommodate more traffic in terms of capacity but the corresponding airspace network cannot accommodate the resulting traffic flow due to the bounds on collision risk.     

低排放燃烧室NO_x排放试验及预测方法研究

为了研究中心分级贫油低排放燃烧室的排放特性和排放预测方法,针对一个低排放头部方案,在单头部燃烧室试验件上,在不同的温度、压力、油气比、供油模式和分级比条件下,测量其排放性能。以Lefebvre排放经验预测公式为基础,采用经验分析方法拟合排放试验数据,归纳出适用于本头部方案的排放预测公式。表征预测好坏的判定系数R2在小工况下和大工况下分别为0.95和0.93,表明预测结果与试验结果符合度较好。小工况和大工况排放特性不同,对仅预燃级喷油的小工况工作模式,NO_x排放主要受化学恰当燃烧温度和预燃级局部当量比的影响;对预燃级和主燃级同时喷油的大工况工作模式,NO_x排放主要受燃烧区温度和主燃级燃油比例的影响。