飞行器红外隐身效能工程评价方法

 针对飞行器的红外隐身问题,推导出红外辐射对比度与作用距离的理论关系,采用指数拟合获得大气透过率与作用距离的近似关系表达式,简化了对作用距离的计算,并通过实际算例考察了目标表面温度、目标发射率和飞行速度对红外辐射对比度及作用距离的影响。结果表明：对比度和作用距离随目标表面温度、发射率及飞行速度的下降趋势基本一致;在一定条件下,对比度可代替作用距离作为评价目标红外隐身效果的简单、快速的参数,对比度越小目标的红外隐身效果越好。对比度的计算快速、准确、灵活性强和适用范围广,为今后进一步对飞行器的红外隐身研究提供一定的理论参考。     

An improved real-time cycle slip correction algorithm based on Doppler-aided signals for BDS triple-frequency measurements

Doppler, which is an instantaneous GNSS observable signal, has been proven effective in determining velocity and acceleration due to its high availability and accuracy. We propose a real-time triple-frequency cycle slip correction (CSC) method based on Doppler-aided signals because Doppler shift is time-independent and immune to cycle slips. When the sampling interval is less than 1 s, cycle slips on triple-frequency can be detected and repaired using pure Doppler data with high reliability; however, this method cannot be used when the sampling interval exceeds 1 s because the integral cumulative error of Doppler increases significantly. For such cases, a modified triple-frequency CSC approach has been developed based on the raw phase and smoothed code data that was refined using the Doppler signal. To suppress the effect of the integral Doppler error, a balance factor is introduced to adjust the contributions of the raw code and Doppler observables. After the refinement of the GNSS data, three independent combinations need be selected to detect and repair cycle slips with triple-frequency observations. Four constrained criteria have been proposed to select optimal combinations that can reduce the residual ionospheric delay (RID) and measurement noise to a low level. Finally, experiments were carried out to test the performance of the new method using real triple-frequency BDS observations (GPST: 3:15:00–5:55:00, March 23, 2018). The results show that pure Doppler can detect and repair cycle slips effectively with small intervals, and modified Hatch-Melbourne-Wübbena (HMW) method based on Doppler-aided signals can achieve 99.7% success rate in cycle slip correction with large intervals (up to 30 s).     

Comparison of RO tropopause height based on different tropopause determination methods

The tropopause is an important boundary in the Earth’s atmosphere, and has been the subject of close attention from atmosphere and climate researchers. To monitor the global tropopause using radio occultation (RO) data, there are two primary methods, one is the widely used temperature lapse rate method, and the other is the bending angle covariance transform method which is unique to RO data. We use FengYun3-C (FY3C) and Meteorological Operational Satellite Program (MetOp) RO data and European Centre for Medium-Range Weather Forecasts (ECMWF) operational analysis data to determine differences in RO tropopause height calculated by these two methods. We compute biases of the RO lapse rate tropopause height (LRTH) and the RO bending angle tropopause height (BATH) relative to the ECMWF LRTH. The dependences of the tropopause height biases on tropopause height (TPH) retrieval method, latitude, season and RO mission are investigated. The results indicate that BATH show a consistent 0.8–1.2 km positive bias over the tropics and high latitude regions compared with LRTH, however, over 25° to 40° latitude in both hemisphere, BATH results are less stable. Furthermore, the mean bias between BATH and LRTH displayed a different symmetrical characteristic from 2017.12 to 2018.2 (DJF) compared to 2018.6–2018.8 (JJA). However, except for some bias over Antarctica, the mean value of both LRTH and BATH show a similar tropopause variation, indicating the consistency of both methods.     

The attitude inversion method of geostationary satellites based on unscented particle filter

The attitude information of geostationary satellites is difficult to be obtained since they are presented in non-resolved images on the ground observation equipment in space object surveillance. In this paper, an attitude inversion method for geostationary satellite based on Unscented Particle Filter (UPF) and ground photometric data is presented. The inversion algorithm based on UPF is proposed aiming at the strong non-linear feature in the photometric data inversion for satellite attitude, which combines the advantage of Unscented Kalman Filter (UKF) and Particle Filter (PF). This update method improves the particle selection based on the idea of UKF to redesign the importance density function. Moreover, it uses the RMS-UKF to partially correct the prediction covariance matrix, which improves the applicability of the attitude inversion method in view of UKF and the particle degradation and dilution of the attitude inversion method based on PF. This paper describes the main principles and steps of algorithm in detail, correctness, accuracy, stability and applicability of the method are verified by simulation experiment and scaling experiment in the end. The results show that the proposed method can effectively solve the problem of particle degradation and depletion in the attitude inversion method on account of PF, and the problem that UKF is not suitable for the strong non-linear attitude inversion. However, the inversion accuracy is obviously superior to UKF and PF, in addition, in the case of the inversion with large attitude error that can inverse the attitude with small particles and high precision.     

基于位姿测量不确定度的飞机对接质量评估

针对基于位姿的数字化测量辅助飞机大部件对接技术的发展与应用,对位姿测量不确定度以及基于不确定度的质量评价方法进行了研究.给出了数字化对接环境下大部件位姿的数学表达形式及意义.提出了基于协方差矩阵的位姿测量不确定度解析算法,并通过仿真算例与蒙特卡洛仿真法进行了对比,验证了该算法的有效性.给出了飞机大部件对接过程数字化测量工艺能力指数的概念,用于对测量结果的可信性进行评价;通过构建位姿测量不确定度与对接质量评估指标间的映射关系,提出了一种基于位姿测量不确定度的大部件对接质量评估方法,并以机翼-机身对接过程为案例,对方法的可行性、算法的有效性进行了验证.     

嵌入式系统在电气控制中的尝试

本文综述了嵌入式系统及其发展和在工业控制中的应用 ,提出在电气控制中应用的设想     

基于神经网络实现的遥测帧码数字相关检测器

本文提出了一种利用帧同步码（以下简称帧码）符合度特征，采用多比特观测窗口技术的数字相关检测模型，基于上述模型，采用神经网络实现了这种数字相关检测器。实验结果表明：该数字相关检测器对帧码出现的误码和码元滑动的情况均有较高的检测率。     

CAPP中工艺装备选择系统

介绍了CAPP中工艺装备选择系统的设计思想、功能结构和信息模型，论述了工艺装备选择的方法与过程．     

三牙轮钻头工艺图自动生成系统

介绍了三牙轮钻头工艺图自动生成系统的结构和功能，论述了工艺图信息模型和工艺图自动生成的的工作原理，提出了综合参数化特征组合和样板图尺寸置换２种方法自动生成工艺图的方法。