飞机铆接件隐藏缺陷的远场涡流检测探头优化与试验

远场涡流检测技术因检测深度深和检测结果可靠性高等诸多优点适合飞机多层金属铆接构件的快速检测。针对飞机铆接件铆钉孔沿边隐藏裂纹的原位检测，建立了多层金属铆接构件隐藏缺陷平面远场涡流检测有限元模型，对激励线圈内径、磁路结构以及屏蔽阻尼进行了仿真优化，研制了激励线圈和检测线圈均带组合屏蔽结构的传感器，采用激励-检测线圈环绕铆钉旋转扫描的方式，研究多层金属铆接构件铆钉孔沿边隐藏裂纹信号特征。仿真与试验结果表明：罐形磁芯聚磁效果是柱形磁芯的1.85倍，采用铝+铜组合屏蔽罩能够将远场区提前10 mm，检测线圈位于缺陷正上方时，检测信号的幅值和相位存在极大值，且极大值随着缺陷埋深的增加逐渐下降，研究成果可望用于指导飞机多层金属铆接构件的工程检测实践。     

Near real-time BDS GEO satellite orbit determination and maneuver analysis with reversed point positioning

The Geostationary Earth Orbit (GEO) satellite is a crucial part of the BeiDou Navigation Satellite System (BDS) constellation. However, due to various perturbation forces acting on the GEO satellite, it drifts gradually over time. Thus, frequent orbit maneuvers are required to maintain the satellite at its designed position. During the orbit maneuver and recovery periods, the orbit quality of the maneuvered satellite computed with broadcast navigation ephemeris will be significantly degraded. Furthermore, the conventional dynamic Precise Orbit Determination (POD) approach may not work well, because of a lack of publicly available satellite information for modeling the thrust forces. In this paper, a near real-time approach free of thrust forces modeling is proposed for BDS GEO satellite orbit determination and maneuver analysis based on the Reversed Point Positioning (RPP). First, the station coordinates and receiver clock offsets are estimated by GPS/BDS combined Single Point Positioning (SPP) with single-frequency phase-smoothed pseudorange observations. Then, with the fixed station coordinates and receiver clock offsets, the RPP method can be conducted to determine the GEO satellite orbits. When no orbit maneuvers occur, the proposed method can obtain orbit accuracies of 0.92, 2.74, and 8.30?m in the radial, along-track, and cross-track directions, respectively. The average orbit-only Signal-In-Space Range Error (SISRE) is 1.23?m, which is slightly poorer than that of the broadcast navigation ephemeris. Using four days of GEO maneuvered datasets, it is further demonstrated that the derived orbits can be employed to characterize the behaviors of GEO satellite maneuvers, such as the time span of the maneuver as well as the satellite thrusting accelerations. These results prove the efficiency of the proposed method for near real-time GEO satellite orbit determination during maneuvers.     

Ground-based and satellite DC-ULF electric field anomalies around Wenchuan M8.0 earthquake

The ground-based and satellite DC-ULF electric field data were analyzed around Wenchuan M8.0 earthquake on May 12, 2008 in China. The results show that ground electric field anomalies occurred at 3 stations located to the north and south of the epicenter with the amplitude of 3–100 mV/km. The change shapes and their amplitude of ground electric field anomalies are different largely due to their individual underground layer conductivity, water level and so on. The analysis of long time series illustrates that the abnormal geoelectric field started since March 2008. Onboard the DEMETER satellite, the ULF waveforms of electric field were collected and processed by wavelet transform method. The disturbances in the ionosphere were about 3–5 mV/m at a frequency band lower than 0.5 Hz. When the ground and space electric field anomalies were compared, their occurrence time and spatial distribution points are consistent with each other, including the long time anomalies from March 2008 and the short term ones 1–2 days before the Wenchuan earthquake. Finally, the coupling mechanism was discussed.     

Inertial aided BDS triple-frequency integer ambiguity rounding method

The integer ambiguity resolution (AR) of carrier phase is significant for Global Navigation Satellite System (GNSS) precise positioning. However, in kinematic case, single-epoch AR methods based on alone GNSS are usually not reliable due to the instable pseudorange accuracy. Moreover, the computation of classical AR method Least Squares Ambiguity Decorrelation Adjustment (LAMBDA) is large. Thus, the inertial measurement unit (IMU) is introduced, a new inertial-aided AR method that directly rounds the float ambiguity of BeiDou triple-frequency combined observations, which is characterized by long wavelength, low carrier-phase noise and ionospheric delay, is proposed. The mathematical model of the new method is derived first. Then the impacts of the carrier-phase noise, ionospheric delay and inertial navigation system (INS) position error on the AR success ratio of combined observation are analyzed through probabilistic approach. Based on above investigation, the combinations (0, ?1, 1), (1, 4, ?5) and (4, ?2, ?3) are selected to resolve the original ambiguity. A vehicular integrated navigation test is performed to demonstrate the proposed method. The results show that the average AR success ratios of the three selected combinations, whose float ambiguity errors are 0.041, 0.146, 0.279 cycle respectively, are above 97.25% without regard to low-elevation C05. With respect to positioning accuracy based on our AR method when compared with IE software, the east, north, up error RMS of position are 0.042, 0.024, 0.069 m, respectively. In terms of the AR recover after the BeiDou signals outage, as long as 62 s BeiDou signal complete outage, all the ambiguities of all satellites could be re-fixed immediately. Besides, during the 90 s signals partial outage, the AR is not influenced by the position error, since the float ambiguity errors are all below half-cycle. The research of this contribution demonstrates the effectiveness of the proposed new method, which indicates it is applicable to kinematic positioning, even in BDS degraded and denied environments.     

展成法加工的弧齿锥齿轮仿切几何建模方法

提出了一种针对展成法加工的弧齿锥齿轮几何建模方法.该方法有两个步骤:(1)通过模仿弧齿锥齿轮加工中的切齿建立参考模型;(2)从参考模型上选择数据点,将这些数据点拟合为NURBS曲面,从而建立最终的实体模型.该方法中,通过模仿切削可以避免深奥的数学理论和复杂的方法,方便地在齿轮制造出来之前(设计阶段)得到复杂齿面上的数据点,并有效提高实体模型的精度.另外,最终得到的模型齿面统一由NURBS曲面函数表示,NURBS曲面连续和光滑,可为CAD/CAE广泛使用.实验表明,通过该方法能够精确建立一对弧齿锥齿轮模型,为CAD/CAE建模提供了一种可行有效的思路.     

航天器入轨段测轨数据误差特性及定轨结果分析

分析了航天器发射任务入轨段各类测轨数据的误差特性及入轨段各类测轨数据的常用定轨方法的定轨精度,提出了解决定轨结果一致性差、优选困难的方法,并用仿真计算结果和实战任务数据计算结果予以验证.     

可变参数AWGN深空信道模型特性分析及其仿真

文章在研究深空通信信道的统计特性的基础上,建立了可变参数AWGN（VPAWGN）模型来模拟深空通信信道,主要考虑噪声功率、多普勒频移和路径损耗等参数对信道特征的影响。进一步在Visual C＋＋环境下搭建VPWAGN模型,并对各参数对信道的影响进行验证。     

电桥期间核查方法的探讨

定期做好实验室仪器设备的期间核查是保证检测或校准实验室质量的重要手段,本文通过分析交流、直流电桥的区别,介绍了电桥期间核查的方法,并通过具体实例进行验证,结果表明这种方法不仅能够满足电桥期间核查的需要,而且可以实现两电桥的互查。     

焊接视觉传感及自动跟踪技术的现状与发展

航空航天制造领域的焊接在材料、结构、焊接工艺方法等方面都有其特征,对焊缝自动识别与跟踪的准确性、实时性和适应性也有专门要求。基于结构光法焊缝视觉跟踪技术已经得到实际应用。焊接视觉技术未来的发展应更关注和利用工件焊接区域光学特征。探索多传感信息融合的视觉跟踪方法是航空航天制造焊接自动化的重要研究方向。