小展弦比飞机非线性气动特性风洞与飞行相关性研究

在较大迎角范围，如何由风洞试验数据预计全尺寸小展弦比飞机的非线性气动特性，并与飞行值相关，始终是国际航空界致力解决的重大问题，本项研究采用风洞试验与工程计算相结合的方法，对支架，洞壁、进气，喷流，雷诺数及静弹性等影响相关性的诸因素予以修正，并计及配平影响，从而比较准确地预计出全尺寸收音机的非线性气动特性，预计值与试飞值相比较结果验证了本项研究的可靠性和实用性。     

机床实体模型复模态空间动位移显示技术的研究

介绍了用实体模型在复模态空间显示机床整机动位移的原理和方法。并在VC++6.0开发平台上用OpenGL语言开发了相应软件。解决了以往同类软件动画效果不能真实地表现实际机床整机的动态位移情况的难题。     

Designing space vehicle shields for meteoroid protection: A new analysis

Dual-layer meteroid shields consisting of sacrificial bumper plates spaced some distance outboard from the vehicle hull are the most effective structures yet conceived for protecting space vehicles from supervelocity meteroid impacts. This paper presents a new analysis for designing dual-layer shields. The analysis is based upon energy and momentum conservation, fundamental electromagnetic radiation physics, and observation of results from extensive experimental impact investigations conducted at relatively low velocities (near 7 km/s). One important conclusion is that most of the kinetic energy of a meteoroid striking a dual-layer shield is expended as radiation at the stagnation zone on the face plate of the underlying structure. The analysis includes systematic procedures to evaluate the response of shield designs for a given impact threat. Similar applications of the analysis can be used to support a mathematically rigorous procedure for optimum shield design. The research described here supported the Halley Intercept Mission Project at the Jet Propulsion Laboratory, C.I.T., under Contract No. NAS 7–100, sponsored by the National Aeronautics and Space Administration.     

Telerobotics: problems and research needs

With major emphasis on simulation, a university laboratory telerobotics facility permits problems to be approached by groups of graduate students. Helmet-mounded displays provide realism; the slaving of the display to the human operator's viewpoint gives a sense of `telepresence' that may be useful for prolonged tasks. Using top-down 3-D model control of distant images allows distant images to be reduced to a few parameters to update the model used for display to the human operator in a preview model to circumvent, in part, the communication delay. Also, the model can be used as a format for supervisory control and permit short-term local autonomous operations. Image processing algorithms can be made simpler and faster without trying to construct sensible images from the bottom. Control studies of telerobots lead to preferential manual control modes and, in this university environment, to basic paradigms for human motion and thence, perhaps, to redesign of robotic control, trajectory path planning, and rehabilitation prosthetics. Speculation as to future industrial drives for this telerobotic field suggests efficient roles for government agencies such as NASA     

两凸平面相贯立体的隐藏线消去法

本文介绍了一种消去两相贯凸平面立体的隐藏线算法。首先利用外法线法单体消隐,然后用线与面比较法作组合消隐计算,逐一确定各个单体上可见棱线在组合体上的可见线段,最后显示或绘制所有的可见棱线段和两体的可见交线,得到消隐后的立体图。本法信息输入量较小,功能较强,不但适用于两相贯的凸平面立体的消隐,而且也适用于两迭加的凸平面立体的消隐。本程序还适用于两体具有共面的情况。     

Recurrent isolation of hydrogen peroxide-resistant spores of Bacillus pumilus from a spacecraft assembly facility

While the microbial diversity of a spacecraft assembly facility at the Jet Propulsion Laboratory (Pasadena, CA) was being monitored, H2O2-resistant bacterial strains were repeatedly isolated from various surface locations. H2O2 is a possible sterilant for spacecraft hardware because it is a low-temperature process and compatible with various modern-day spacecraft materials, electronics, and components. Both conventional biochemical testing and molecular analyses identified these strains as Bacillus pumilus. This Bacillus species was found in both unclassified (entrance floors, anteroom, and air-lock) and classified (floors, cabinet tops, and air) locations. Both vegetative cells and spores of several B. pumilus isolates were exposed to 5% liquid H2O2 for 60 min. Spores of each strain exhibited higher resistance than their respective vegetative cells to liquid H2O2. Results indicate that the H2O2 resistance observed in both vegetative cells and spores is strain-specific, as certain B. pumilus strains were two to three times more resistant than a standard Bacillus subtilis dosimetry strain. An example of this trend was observed when the type strain of B. pumilus, ATCC 7061, proved sensitive, whereas several environmental strains exhibited varying degrees of resistance, to H2O2. Repeated isolation of H2O2-resistant strains of B. pumilus in a clean-room is a concern because their persistence might potentially compromise life-detection missions, which have very strict cleanliness and sterility requirements for spacecraft hardware.     

Computer Optimization of FM/FM Telemetry Systems

In this correspondence, the threshold carrier power of FM/FM systems and the receiver IF bandwidth are optimized through a computer program. For a typical set of IRIG (inter-range instrumentation group) channels, it is demonstrated that the required carrier signal-to-noise ratio can be as low as 5 dB (much less than the conventional 12 dB value) in order to maintain the subcarrier signal-to-noise ratio at 12 dB, the threshold level. comparison of the optimized and the conventional taper analysis is tabulated.     

火箭发动机基于神经网络非线性辨识的故障检测

应用神经网络方法，提出了一种液体火箭发动机故障实时检测算法。神经网络采用非线性辨识技术贴近发动机的工作过程，并输出包合发动机故障信息的辨识误差信号。若辨识误差变大超过一定阈值，检测逻辑就预报发动机故障。在发动机启动阶段离线训练神经网络，在发动机稳态过程可以采用离线或在线学习算法。实验研究表明神经网络可以成功地应用于大型泵压式液体火箭发动机的故障检测。     

椭圆振动切削加工的同步控制研究

利用椭圆振动切削加工的回转体表面微织构是在机床主轴旋转、平台进给和装置椭圆振动的联合运动下得到的,机床主轴转动与装置位移输出如果不能保持完全的实时同步,会造成微织构加工的偏差。为了解决这一问题,提出了一种新的基于转角的同步控制方法,该方法在主轴的对位基准处实现装置正弦信号的复位,以修正转速漂移造成的加工位置误差,并通过判断主轴角度信号实时输出对应幅值电压来实时同步信号输出和机床旋转运动。基于LabVIEW FPGA搭建同步控制模块,经试验验证,利用该方法加工的矩形阵列微织构轴向排列与中轴线平行,与周向排列的夹角和仿真结果的偏差不超过0.1°,织构深度随转角的不同发生预设的变化,因此,同步控制方法具有实时同步控制椭圆振动切削装置的能力。     

Regolith X-Ray Imaging Spectrometer (REXIS) Aboard the OSIRIS-REx Asteroid Sample Return Mission

The Regolith X-ray Imaging Spectrometer (REXIS) is the student collaboration experiment proposed and built by an MIT-Harvard team, launched aboard NASA’s OSIRIS-REx asteroid sample return mission. REXIS complements the scientific investigations of other OSIRIS-REx instruments by determining the relative abundances of key elements present on the asteroid’s surface by measuring the X-ray fluorescence spectrum (stimulated by the natural solar X-ray flux) over the range of energies 0.5 to 7 keV. REXIS consists of two components: a main imaging spectrometer with a coded aperture mask and a separate solar X-ray monitor to account for the Sun’s variability. In addition to element abundance ratios (relative to Si) pinpointing the asteroid’s most likely meteorite association, REXIS also maps elemental abundance variability across the asteroid’s surface using the asteroid’s rotation as well as the spacecraft’s orbital motion. Image reconstruction at the highest resolution is facilitated by the coded aperture mask. Through this operation, REXIS will be the first application of X-ray coded aperture imaging to planetary surface mapping, making this student-built instrument a pathfinder toward future planetary exploration. To date, 60 students at the undergraduate and graduate levels have been involved with the REXIS project, with the hands-on experience translating to a dozen Master’s and Ph.D. theses and other student publications.