Variations of the magnetic fields in large solar flares

We present preliminary results from high resolution observations obtained with the Michelson Doppler Imager (MDI) instrument on the SOHO of two large solar flares of 14 July 2000 and 24 November 2000. We show that rapid variations of the line-of-sight magnetic field occured on a time scale of a few minutes during the flare explosions. The reversibility/irreversibility of the magnetic field of both active regions is a very good tool for understanding how the magnetic energy is released in these flares. The observed sharp increase of the magnetic energy density at the time of maximum of the solar flare could involve an unknown component which deposited supplementary energy into the system. This revised version was published online in August 2006 with corrections to the Cover Date.     

Investigation of natural and artificial stimulation of the ionospheric Alfvén resonator at high latitude

A brief review is provided of recent progress in understanding the ionospheric Alfvén resonator (IAR) at high latitude. Firstly, naturally occurring resonances of the IAR as detected by pulsation magnetometers in the auroral zone at Sodankylä and in the polar cap at Barentsburg are considered. The characteristics of the IAR in the two regions are broadly similar, although the effects of solar illumination are less clear at the higher latitudes. Secondly we review recent attempts to stimulate the IAR through high-power radio frequency experiments both in the auroral zone at Tromsø with the European Incoherent SCATter (EISCAT) heater, and within the polar cap at Longyearbyen with the Space Plasma Exploration by Active Radar (SPEAR) facility. In the auroral zone at, Tromsø the stimulated IAR has been observed by ground-based magnetometers, and through electron acceleration observed on the FAST spacecraft. At SPEAR in the polar cap, the stimulated IAR has been investigated, with ground magnetometers, with the first results indicative of a positive detection.     

Maximum Likelihood Elevation Angle Estimates of Radar Targets Using Subapertures

The maximum likelihood estimates of the elevation angles of two closely spaced targets within the beamwidth is considered. For an array divided into three subapertures, a simple, closed form solution is found whose accuracy compares favorably to the maximum likelihood estimate which uses all the individual elements. Simulation results are presented for the case of a radar target located over a smooth reflecting surface.     

Susceptibility of DS/FH,M, Binary DPSK to Partial and Full Band Barrage Jamming

Spread spectrum signaling schemes have been proposed to counter unfriendly, electrical jamming threats. In order to establish their effectiveness, such schemes must be analyzed. This work takes a step in this direction by developing the susceptibility equation, or equivalently, the probability of error, of a direct sequence/frequency hopped (DS/FH), binary differential phase-shift keying (DPSK) system when subjected to a barrage jamming signal. Specific system models are established for the receiving system as well as for the jamming signal and the spread spectrum techniques. Both partial and full band jamming strategies are considered. Graphical results are presented with the conclusions summarizing the spread spectrum effectiveness and the deficiencies of the FH processing gain definition.     

Monitoring the thermal condition of permanent-magnet synchronousmotors

This paper describes a novel approach to monitoring the condition of small permanent-magnet synchronous motors (PMSM) operating under thermal stress. The approach begins with the estimation of temperature-dependent motor parameters from measurements of line voltages and currents. The parameters are then used to derive estimates of motor temperatures. Next, the electrically estimated temperatures are combined with a surface measurement of motor temperature and a dynamic thermal model of the motor to yield an observer that is a Kalman filter. The temperatures estimated by the observer are used for failure prevention. Finally, by modifying the observer, it is tuned to use the geometric properties of its innovation for failure detection. The innovation, that is, the difference between the thermally and electrically estimated temperatures, is monitored and compared against appropriate thresholds to detect failures. Failure detection is demonstrated experimentally, and shown to be capable of distinguishing the conditions of normal operation, and operation with obstructed cooling     

TC-1和Geotail对亚暴过程中近地等离子体片磁扰动的联合观测

以2004年9月28日02:53:20 UT的亚暴为例, 通过TC-1在磁尾约12.5 R_e 和Geotail卫星在近地磁尾等离子体片约8～9 R_e的联合观测, 研究亚暴触发过程中近地磁尾等离子体片中等离子体波动特征. 结果表明, 亚暴触发区是近地磁尾中心等离子体片中较小的一个区域, 在亚暴触发区中低混杂不稳定性在近地磁尾等离子体片中存在, 准垂直传播的低混杂波发生在亚暴触发过程中, 而亚暴触发过程中近地磁尾等离子体片外边界区内的磁场偶极化信号和扰动都非常微弱. 在亚暴触发和亚暴膨胀相过程中出现了多次具有不同特征的磁场偶极化现象.     

Performance Analysis of the Modulation Cancellation Altimeter

The performance of the modulation cancellation altimeter is investigated. Several sources of error are considered, specifically: 1) terrain averaging error; 2) output noise fluctuations; 3) errors due to phase shifts; and 4) acquisition ambiguities. The predominant parameters affecting these errors are investigated with a view towards optimizing the performance of the altimeter.     

Prototype design and testing of a Venus long duration,high altitude balloon

This paper describes the design, fabrication and testing of a full scale prototype balloon intended for long duration flight in the upper atmosphere of Venus. The balloon is 5.5 m in diameter and is designed to carry a 45 kg payload at an altitude of 55 km. The balloon material is a 180 g/m² multi-component laminate comprised of the following layers bonded together from outside to inside: aluminized Teflon film, aluminized Mylar film, Vectran fabric and a polyurethane coating. This construction provides the required balloon functional characteristics of low gas permeability, sulfuric acid resistance and high strength for superpressure operation. The design burst superpressure is 39,200 Pa which is predicted to be 3.3 times the worst case value expected during flight at the highest solar irradiance in the mission profile. The prototype is constructed from 16 gores with bi-taped seams employing a sulfuric acid resistant adhesive on the outside. Material coupon tests were performed to evaluate the optical and mechanical characteristics of the laminate. These were followed by full prototype tests for inflation, leakage and sulfuric acid tolerance. The results confirmed the suitability of this balloon design for use at Venus in a long duration mission. The various data are presented and the implications for mission design and operation are discussed.